Ruthenium dioxide oxidation

Ruthenium—Titanium Oxides. The x-ray diffractioa studies of mthenium—titanium oxide coatiags show that the coatiag components are preseat as the metal dioxides, each ia the mtile form as weU as ia soHd solutioa with each other (13). The developmeat of the crystal stmcture begias to occur at a bake temperature of about 400°C. By foUowiag the diffractioa line for the mtile stmcture, an iacrease ia crystallinity can be seen as temperatures are iacreased to the 600—700°C range. Above these temperatures, the peak begias to separate iato two separate peaks, iadicative of phase separatioa iato iadividual mtile oxides, oae rich ia mthenium and one rich ia titanium. 

Miscellaneous. Ruthenium dioxide-based thick-film resistors have been used as secondary thermometers below I K (92). Ruthenium dioxide-coated anodes ate the most widely used anode for chlorine production (93). Ruthenium(IV) oxide and other compounds ate used in the electronics industry as resistor material in apphcations where thick-film technology is used to print electrical circuits (94) (see Electronic materials). Ruthenium electroplate has similar properties to those of rhodium, but is much less expensive. Electrolytes used for mthenium electroplating (95) include [Ru2Clg(OH2)2N] Na2[Ru(N02)4(N0)0H] [13859-66-0] and (NH 2P uds(NO)] [13820-58-1], Several photocatalytic cycles that generate... 

A high yield ot the resulting perfluorononanoic acid is obtained by the oxidation of (perfluorooctyl)ethylene with a small amount of ruthenium dioxide and an oxidant [41] (equation 33). 

Chloro-2-(3-methyl-4H-1,2,4-triazol-4-yDbenzophenone (Oxidation of 7solution prepared by adding sodium periodate (2 g) to a stirred suspension of ruthenium dioxide (200 mg) in water (35 ml). The mixture became dark. Additional sodium periodate 18 g) was added during the next 15 minutes. The ice-bath was removed and the mixture was stirred for 45 minutes. Additional sodium periodate (4 g) was added and the mixture was stirred at ambient temperature for 18 hours and filtered. The solid was washed with acetone and the combined filtrate was concentrated in vacuo. The residue was suspended in water and extracted with methylene chloride. The extract was dried over anhydrous potassium carbonate and concentrated. The residue was chromatographed on silica... 

Recently it has been shown that the oxides of the platinum metals can have a higher corrosion resistance than the metals themselves , and have sufficient conductivity to be used as coatings for anodes, e.g. with titanium cores. Anodes with a coating of ruthenium dioxide are being developed for use in mercury cells for the electrolysis of brine to produce chlorine , since they are resistant to attack if in contact with the sodium-mercury amalgam. 

At one stage in our project we were surprised to learn that some workers had found difficulties in preparing the tetroxide from the dioxide, until we experienced the same trouble. This problem has now been resolved (3). Ruthenium dioxide is available commercially in both anhydrous and hydrated forms, the former being obtained by direct oxidation of ruthenium metal and the latter by a precipitation process. Only the hydrated form is oxidizable under the mild conditions (2,3) that we use and this form must be specified when purchasing the dioxide. It is noteworthy that the dioxide recovered from carbohydrate oxidations is always easily re-oxidized to the tetroxide. The stoichiometry has been determined of both the oxidation of the dioxide by periodate and reduction of the tetroxide which results on oxidation of an alcohol. 

A novel oxidation of sulphilimines using ruthenium tetroxide (generated in situ from ruthenium dioxide in a two-phase system) for the preparation of sulphoximines has been reported and proceeds in yields greater than 85%185. 

Titanium dioxide is a catalytically inactive but rather corrosion-resistant material. Ruthenium dioxide is one of the few oxides having metal-like conductivity. It is catalytically quite active toward oygen and chlorine evolution. However, its chemical stability is limited, and it dissolves anodically at potentials of 1.50 to 1.55 V (RHE) with appreciable rates. A layer of mixed titanium and ruthenium dioxides containing 1-2 mg/cm of the precious metal has entirely unique properties in terms of its activity and selectivity toward chlorine evolution and in terms of its stability. With a working current density in chlorine evolution of 20 to 50mA/cm, the service life of such anodes is several years (up to eight years). 

The layer of titanium and ruthenium oxides usually is applied to a titanium substrate pyrolytically, by thermal decomposition (at a temperature of about 450°C) of an aqueous or alcoholic solution of the chlorides or of complex compounds of titanium and rathenium. The optimum layer composition corresponds to 25 to 30 atom % of ruthenium. The layer contains some quantity of chlorine its composition can be written as Ruq 2sTio 750(2- c)Cl r At this deposition temperature and Ru-Ti ratio, the layer is a poorly ordered solid solution of the dioxides of ruthenium and titanium. Chlorine is completely eliminated from the layer when this is formed at higher temperatures (up to 800°C), and the solid solution decomposes into two independent phases of titanium dioxide and ruthenium dioxide no longer exhibiting the unique catalytic properties. 

Nitrosyl perchlorate Organic materials Perchloric acid Alcohols Permanganic acid Organic materials Peroxodisulfuric acid Organic liquids Potassium dioxide Ethanol Potassium perchlorate Ethanol Potassium permanganate Ethanol, etc. Ruthenium(VIII) oxide Organic materials Silver perchlorate Aromatic compounds Sodium peroxide Hydroxy compounds Uranium hexafluoride Aromatic hydrocarbons, etc. Uranyl perchlorate Ethanol See v-halomides Alcohols... 

Uniformity of the electrical double layer on oxides plot of -gj vs -ApH master curves for rutile, ruthenium dioxide and hematite. The concentration of KNO3 is indicated. 

Palladium(II) oxide, 4825 Palladium(IV) oxide, 4835 Perchloric acid, 3998 Periodic acid, 4425 Permanganic acid, 4434 Peroxodisulfuric acid, 4482 Peroxodisulfuryl difluoride, 4328 Peroxomonosulfuric acid, 4481 Peroxytrifluoroacetic acid, 0666 Platinum hexafluoride, 4371 Platinum(IV) oxide, 4836 Plutonium hexafluoride, 4372 Potassium bromate, 0255 Potassium chlorate, 4017 Potassium dichromate, 4248 Potassium iodate, 4619 Potassium nitrate, 4650 Potassium nitrite, 4649 Potassium perchlorate, 4018 Potassium periodate, 4620 Potassium permanganate, 4647 Rhenium hexafluoride, 4373 Rubidium fluoroxysulfate, 4309 Ruthenium(VIII) oxide, 4862 Selenium dioxide, 4838 Selenium dioxide, 4838 Silver permanganate, 0021 Sodium chlorate, 4039 Sodium chlorite, 4038 Sodium dichromate, 4250 Sodium iodate, 4624 Sodium nitrate, 4721 Sodium nitrite, 4720... 

J.-M. Zen, A. S. Kumar and J.-C. Chen, Electrochemical Behavior of Lead-Ruthenium Oxide Pyrochlore Catalyst Redox Characteristics in Comparison with that of Ruthenium Dioxide, J. Mol. Catal. A Chem. 165 (2001) 177-188. 

The ruthenium tetroxide dioxide catalytic system is effective for the oxidation of alkanols, although it will also react with any alkene groups or amine substituents that are present. The catalyst can be used in aqueous acetonitrile containing tetra-butylammonium hydroxide with platinum electrodes in an undivided cell Primary alcohols are oxidised to the aldehyde and secondary alcohols to the ketone [30]. Anodic oxidation of ruthenium dioxide generates the tetroxide, which is the effective oxidising agent. 

In another procedure, oxidation is carried out in the presence of chloride ions and ruthenium dioxide [31]. Chlorine is generated at the anode and this oxidises ruthenium to the tetroxide level. The reaction medium is aqueous sodium chloride with an inert solvent for the alkanol. Ruthenium tetroxide dissolves in the organic layer and effects oxidation of the alkanol. An undivided cell is used so that the chlorine generated at the anode reacts with hydroxide generated at the cathode to form hypochlorite. Thus this electrochemical process is equivalent to the oxidation of alkanols by ruthenium dioxide and a stoichiometric amount of sodium hypochlorite. Secondary alcohols are oxidised to ketones in excellent yields. 1,4- and 1,5-Diols with at least one primary alcohol function, are oxidised to lactones while... 

Passage of 1.0 mol of electrons (one faraday, 96,485 A s) will produce 1.0 mol of oxidation or reduction—in this case, 1.0 mol of Cl- converted to 0.5 mol of Cl2, and 1.0 mol of water reduced to 1.0 mol of OH- plus 0.5 mol of H2. Thermodynamically, the electrical potential required to do this is given by the difference in standard electrode potentials (Chapter 15 and Appendix D) for the anode and cathode processes, but there is also an additional voltage or overpotential that originates in kinetic barriers within these multistep gas-evolving electrode processes. The overpotential can be minimized by catalyzing the electrode reactions in the case of chlorine evolution, this can be done by coating the anode with ruthenium dioxide. 

Ruthenium dioxide [12157-25-6] M 133.1. Freed from nitrates by boiling in distilled water and filtering. A more complete purification is based on fusion in a KOH-KNO3 mix to form the soluble ruthenate and perruthenate salts. The melt is dissolved in water, and filtered, then acetone is added to reduce the ruthenates to the insoluble hydrate oxide which, after making a slurry with paper pulp, is filtered and ignited in air to form the anhydrous oxide [Campbell, Ortner and Anderson AC 33 58 1961]. 

Mention may be made, finally, of an unsuccessful attempt, recently described by Berkowitz and Bylander,141 to prepare the still unknown substance glycollic lactone by ruthenium tetroxide oxidation of ethylene oxide in carbon tetrachloride at 0°. Tarry products were obtained, which could have been Canned by ruthenium dioxide-oatalyred polymerisation f thiB highly strained a-lactone. 

---