Rhodium cycle

the countercation of 4.5 and the other anionic species is the hydronium ion, i.e., protonated water. If a ligand such as PPhj is added, it gets converted to HPPhj which acts as the countercation. Second, 4.5 to 4.6 is an oxidative addition reaction, 4.6 to 4.7 is an insertion reaction, and 4.8 to 4.5 is a reductive elimination reaction. Third, although the main product-forming reaction is the reductive elimination step, hydrolysis of 4.8 to 4.9 also gives acetic acid. The complex 4.9 plays an important role in the carbonylation of propanol and other higher alcohols (see Section 4.3). 

---

The key features of both catalytic cycles are similar. Alkene coordination to the metal followed by insertion to yield an alkyl-metal complex and CO insertion to yield an acyl-metal complex are common to both catalytic cycles. The oxidative addition of hydrogen followed by reductive elimination of the aldehyde regenerates the catalyst (Scheme 2 and middle section of Scheme 1). The most distinct departure in the catalytic cycle for cobalt is the alternate possibility of a dinuclear elimination occurring by the in-termolecular reaction of the acylcobalt intermediate with hydridotetracarbonylcobalt to generate the aldehyde and the cobalt(0) dimer.11,12 In the cobalt catalytic cycle, therefore, the valence charges can be from +1 to 0 or +1 to +3, while the valence charges in the rhodium cycles are from +1 to +3. 

A nucleophilic attack by 4.7 on CH3I produces 4.8 and I. Conversion of 4.8 to 4.9 is an example of a carbonyl insertion into a metal alkyl bond. Another CO group adds onto the 16-electron species 4.9 to give 4.10, which in turn reacts with I to eliminate acetyl iodide. Formation of acetic acid and recycling of water occur by reactions already discussed for the rhodium cycle. Apart from these basic reactions there are a few other reactions that lead to product and by-product formations. As shown in Fig. 4.4, both 4.9 and 4.10 react with water to give acetic acid. The hydrido cobalt carbonyl 4.11 produced in these reactions catalyzes Fischer-Tropsch-type reactions and the formation of byproducts. Reactions 4.6 and 4.7 ensure that there is equilibrium between 4.7 and 4.11. 

There are two main differences between cobalt- and rhodium-based catalytic cycles. In the cobalt-catalyzed cycle it is the nucleophilic attack by 4.7 on CH3I rather than the oxidative addition of CH3I on any unsaturated 16-electron species that initiates the catalytic cycle. Second, in the rhodium cycle reductive elimination generates acetyl iodide, whereas in the cobalt cycle it is the attack by I on 4.10 that produces acetyl iodide. Thus oxidative addition and reductive elimination steps are not involved in the cobalt cycle, but play crucial roles in the rhodium cycle. 

There is more to tire Wilkinson hydrogenation mechanism tlian tire cycle itself a number of species in tire cycle are drained away by reaction to fomi species outside tire cycle. Thus, for example, PPh (Ph is phenyl) drains rhodium from tire cycle and tlius it inliibits tire catalytic reaction (slows it down). However, PPh plays anotlier, essential role—it is part of tire catalytically active species and, as an electron-donor ligand, it affects tire reactivities of tire intemiediates in tire cycle in such a way tliat tliey react rapidly and lead to catalysis. Thus, tliere is a tradeoff tliat implies an optimum ratio of PPh to Rli. 

Miscellaneous. Ruthenium dioxide-based thick-film resistors have been used as secondary thermometers below I K (92). Ruthenium dioxide-coated anodes ate the most widely used anode for chlorine production (93). Ruthenium(IV) oxide and other compounds ate used in the electronics industry as resistor material in apphcations where thick-film technology is used to print electrical circuits (94) (see Electronic materials). Ruthenium electroplate has similar properties to those of rhodium, but is much less expensive. Electrolytes used for mthenium electroplating (95) include [Ru2Clg(OH2)2N] Na2[Ru(N02)4(N0)0H] [13859-66-0] and (NH 2P uds(NO)] [13820-58-1], Several photocatalytic cycles that generate... 

Wilkinson Hyd.rogena.tion, One of the best understood catalytic cycles is that for olefin hydrogenation in the presence of phosphine complexes of rhodium, the Wilkinson hydrogenation (14,15). The reactions of a number of olefins, eg, cyclohexene and styrene, are rapid, taking place even at room temperature and atmospheric pressure but the reaction of ethylene is extremely slow. Complexes of a number of transition metals in addition to rhodium are active for the reaction. 

The Wilkinson hydrogenation cycle shown in Figure 3 (16) was worked out in experiments that included isolation and identification of individual rhodium complexes, measurements of equiUbria of individual steps, deterrnination of rates of individual steps under conditions of stoichiometric reaction with certain reactants missing so that the catalytic cycle could not occur, and deterrnination of rates of the overall catalytic reaction. The cycle demonstrates some generally important points about catalysis the predominant species present in the reacting solution and the only ones that are easily observable by spectroscopic methods, eg, RhCl[P(CgH 2]3> 6 5)312 (olefin), and RhCl2[P(CgH )2]4, are outside the cycle, possibly in virtual equiUbrium with... 

The catalytic cycle (Fig. 5) (20) is well estabUshed, although the details of the conversion of the intermediate CH COI and methanol into the product are not well understood the mechanism is not shown for this part of the cycle, but it probably involves rhodium in a catalytic role. The CH I works as a cocatalyst or promoter because it undergoes an oxidative addition with [Rh(CO)2l2]% and the resulting product has the CO ligand bonded cis to the CH ligand these two ligands are then poised for an insertion reaction. 

Cases of the S-coordinated rhodium and iridium are quite scarce. To complete the picture, we next consider the possibilities of S-coordination using complicated derivatives of thiophene. 2,5-[Bis(2-diphenylphosphino)ethyl]thiophene is known to contain three potential donor sites, two phosphorus atoms and the sulfur heteroatom, the latter being a rather nucleophilic center (93IC5652). A more typical situation is coordination via the phosphorus sites. It is also observed in the product of the reaction of 2,5-bis[3-(diphenylphosphino)propyl]thiophene (L) with the species obtained after treatment of [(cod)Rh(acac)] with perchloric acid (95IC365). Carbonylation of [Rh(cod)L][C104]) thus prepared yields 237. Decarbonylation of 237 gives a mixture of 238 and the S-coordinated species 239. Complete decarbonylation gives 240, where the heterocycle is -coordinated. The cycle of carbonylation decarbonylation is reversible. 

As an introductory example we take one of the key reactions in cleaning automotive exhaust, the catalytic oxidation of CO on the surface of noble metals such as platinum, palladium and rhodium. To describe the process, we will assume that the metal surface consists of active sites, denoted as We define them properly later on. The catalytic reaction cycle begins with the adsorption of CO and O2 on the surface of platinum, whereby the O2 molecule dissociates into two O atoms (X indicates that the atom or molecule is adsorbed on the surface, i.e. bound to the site ) ... 

The rhodium loss to the hydrocarbon phase was analyzed by atomic absorption. We found that for a thermomorphic catalyst solution that was cycled three times that the rhodium loss was below the 0.1 ppm detection limit of their instrument. 

Various other transition metal complexes are also useful, including rhodium,195 palladium,196 and molybdenum197 compounds. The catalytic cycle can generally be represented as shown below.198... 

Fig. 10.8. Basic catalytic cycle and energy profile for rhodium-catalyzed carbenoid reactions. Reproduced from J. Am. Chem. Soc., 124, 1014 (2002), by permission of the American Chemical Society.

The hydrogenation of simple alkenes using cationic rhodium precatalysts has been studied by Osborn and Schrock [46-48]. Although kinetic analyses were not performed, their collective studies suggest that both monohydride- and dihydride-based catalytic cycles operate, and may be partitioned by virtue of an acid-base reaction involving deprotonation of a cationic rhodium(III) dihydride to furnish a neutral rhodium(I) monohydride (Eq. 1). This aspect of the mechanism finds precedent in the stoichiometric deprotonation of cationic rhodium(III) dihydrides to furnish neutral rhodium(I) monohydrides (Eq. 2). The net transformation (H2 + M - X - M - H + HX) is equivalent to a formal heterolytic activation of elemental... 

The combined information gathered from kinetic studies,184 in situ high-pressure NMR experiments,184,185,195 and the isolation of intermediates related to catalysis, leads to a common mechanism for all the hydrogenolysis reactions of (102)-(104) and other thiophenes catalyzed by triphos- or SULPHOS-rhodium complexes in conjuction with strong Bronsted bases. This mechanism (Scheme 41) involves the usual steps of C—S insertion, hydrogenation of the C—S inserted thiophene to the corresponding thiolate, and base-assisted reductive elimination of the thiol to complete the cycle.184 185 195-198... 

No catalyst has an infinite lifetime. The accepted view of a catalytic cycle is that it proceeds via a series of reactive species, be they transient transition state type structures or relatively more stable intermediates. Reaction of such intermediates with either excess ligand or substrate can give rise to very stable complexes that are kinetically incompetent of sustaining catalysis. The textbook example of this is triphenylphosphine modified rhodium hydroformylation, where a plot of activity versus ligand metal ratio shows the classical volcano plot whereby activity reaches a peak at a certain ratio but then falls off rapidly in the presence of excess phosphine, see Figure... 

---