Reactors emulsion polymerization

A summary of the nine batch reactor emulsion polymerizations and fifteen tubular reactor emulsion polymerizations are presented in Tables III IV. Also, many tubular reactor pressure drop measurements were performed at different Reynolds numbers using distilled water to determined the laminar-turbulent transitional flow regime. 

Types of Reactor Processes Batch Reactors Semibatch Reactors Continuous Reactors Emulsion Polymerization Kinetics Other Preparation Methods... 

Wicker tube reactor Emulsion polymerization 100-m-length tube, with an inner diameter of 1 cm high cooling capacity residence time distribution comparable with a cascade of 600-1500 continuous stirred-tank reactors 177... 

In a semicontinuous reactor in which monomers, surfactant, initiator, and water may be continuously fed into the reactor, emulsion polymerization does not follow the sequence of events described above. Thus, slow monomer feed and fast surfactant feed may lead to a system composed of polymer particles and micelles (Figure 6.3(a)). The system will contain only monomer-swoDen polymer particles if both monomer and surfactant are fed slowly (Figure 6.3(b)). On the other hand, a fast monomer feed and a low surfactant feed will lead to a system containing monomer droplets and polymer particles (Figure 6.3(c)). 

Figure 11 Variation of -ln(l-c) normalized by the kinematic viscosity V and volume fraction of polymer (j) with the square root of power consumption for the stirred-reactor emulsion polymerization of vinyl chloride-ethyl acrylate mixtures according to Lowry et al. (15) using the data of ref. 17.

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

M ass Process. In the mass (or bulk) (83) ABS process the polymerization is conducted in a monomer medium rather than in water. This process usually consists of a series of two or more continuous reactors. The mbber used in this process is most commonly a solution-polymerized linear polybutadiene (or copolymer containing sytrene), although some mass processes utilize emulsion-polymerized ABS with a high mbber content for the mbber component (84). If a linear mbber is used, a solution of the mbber in the monomers is prepared for feeding to the reactor system. If emulsion ABS is used as the source of mbber, a dispersion of the ABS in the monomers is usually prepared after the water has been removed from the ABS latex. 

Soap-starved recipes have been developed that yield 60 wt % soHds low viscosity polymer emulsions without concentrating. It is possible to make latices for appHcation as membranes and similar products via emulsion polymerization at even higher soHds (79). SoHds levels of 70—80 wt % are possible. The paste-like material is made in batch reactors and extmded as product. 

Fig. 3. Emulsion polymerization plant A, emulsion feed tank B, polymerization reactor C, dmmming tank F, filter M, meter P, pressure gauge and T,...

Emulsion Polymerization. Emulsion and suspension reactions are doubly heterogeneous the polymer is insoluble in the monomer and both are insoluble in water. Suspension reactions are similar in behavior to slurry reactors. Oil-soluble initiators are used, so the monomer—polymer droplet is like a small mass reaction. Emulsion polymerizations are more complex. Because the monomer is insoluble in the polymer particle, the simple Smith-Ewart theory does not apply (34). 

Processes that are essentially modifications of laboratory methods and that allow operation on a larger scale are used for commercial preparation of vinyhdene chloride polymers. The intended use dictates the polymer characteristics and, to some extent, the method of manufacture. Emulsion polymerization and suspension polymerization are the preferred industrial processes. Either process is carried out in a closed, stirred reactor, which should be glass-lined and jacketed for heating and cooling. The reactor must be purged of oxygen, and the water and monomer must be free of metallic impurities to prevent an adverse effect on the thermal stabiUty of the polymer. 

The aqueous emulsion polymerization can be conducted by a batch, semibatch, or continuous process (Fig. 5). In a simple batch process, all the ingredients are charged to the reactor, the temperature is raised, and the polymerization is mn to completion. In a semibatch process, all ingredients are charged except the monomers. The monomers are then added continuously to maintain a constant pressure. Once the desired soflds level of the latex is reached (typically 20—40% soflds) the monomer stream is halted, excess monomer is recovered and the latex is isolated. In a continuous process (37), feeding of the ingredients and removal of the polymer latex is continuous through a pressure control or rehef valve. 

Flexible batch. Both the formula and the processing instructions can change from batch to batch. Emulsion polymerization reactors are a good example of a flexible batch facility. The recipe for each produc t must detail Both the raw materials required and how conditions within the reac tor must be sequenced in order to make the desired product. 

Similarly, it is often impossible, or at least very difficult, to experimentally determine the characteristics of a measurement system under the conditions where it is used. It is certainly possible to fill an emulsion polymerization reactor with water and determine the dynamic-characteristics of the temperature measurement system. However, it is not possible to determine these characteristics when the reactor is filled with the emulsion under polymerization conditions. 

A semi-batch reactor has the same disadvantages as the batch reactor. However, it has the advantages of good temperature control and the capability of minimizing unwanted side reactions by maintaining a low concentration of one of the reactants. Semi-batch reactors are also of value when parallel reactions of different orders occur, where it may be more profitable to use semi-batch rather than batch operations. In many applications semi-batch reactors involve a substantial increase in the volume of reaction mixture during a processing cycle (i.e., emulsion polymerization). 

Figure 3 The schematical representation of a typical laboratory scale stirred reactor system for emulsion polymerization.

Continuous emulsion polymerization systems are studied to elucidate reaction mechanisms and to generate the knowledge necessary for the development of commercial continuous processes. Problems encountered with the development of continuous reactor systems and some of the ways of dealing with these problems will be discussed in this paper. Those interested in more detailed information on chemical mechanisms and theoretical models should consult the review papers by Ugelstad and Hansen (1), (kinetics and mechanisms) and by Poehlein and Dougherty (2, (continuous emulsion polymerization). 

In order to be economically viable, a continuous emulsion polymerization process must be able to produce a latex which satisfies application requirements at high rates without frequent disruptions. Since most latex products are developed in batch equipment, the problems associated with converting to continuous systems can be significant. Making such a change requires an understanding of the differences between batch and continuous reactors and how these differences influence product properties and reactor performance. 

Continuous-Emulsion Polymerization of Styrene in a Tubular Reactor... 

The advantages of continuous tubular reactors are well known. They include the elimination of batch to batch variations, a large heat transfer area and minimal handling of chemical products. Despite these advantages there are no reported commercial instances of emulsion polymerizations done in a tubular reactor instead the continuous emulsion process has been realized in series-connected stirred tank reactors (1, . ... 

A few workers have examined the continuous emulsion polymerization process in a tubular reactor (, 5,, the initial work... 

The work reported here is part of a continuing program on the emulsion polymerization of styrene in a tubular reactor. It is now evident that the reactor construction is of primary importance in avoiding the problem of reactor plugging. The plugging is associated with a wall effect so that both the reactor dimensions and the nature of the wall surface are important. 

There are many variations on this theme. Fed-batch and continuous emulsion polymerizations are common. Continuous polymerization in a CSTR is dynamically unstable when free emulsifier is present. Oscillations with periods of several hours will result, but these can be avoided by feeding the CSTR with seed particles made in a batch or tubular reactor. 

Using copolymerization theory and well known phase equilibrium laws a mathematical model is reported for predicting conversions in an emulsion polymerization reactor. The model is demonstrated to accurately predict conversions from the head space vapor compositions during copolymerization reactions for two commercial products. However, it appears that for products with compositions lower than the azeotropic compositions the model becomes semi-empirical. 

This paper presents the physical mechanism and the structure of a comprehensive dynamic Emulsion Polymerization Model (EPM). EPM combines the theory of coagulative nucleation of homogeneously nucleated precursors with detailed species material and energy balances to calculate the time evolution of the concentration, size, and colloidal characteristics of latex particles, the monomer conversions, the copolymer composition, and molecular weight in an emulsion system. The capabilities of EPM are demonstrated by comparisons of its predictions with experimental data from the literature covering styrene and styrene/methyl methacrylate polymerizations. EPM can successfully simulate continuous and batch reactors over a wide range of initiator and added surfactant concentrations. 

The physical picture of emulsion polymerization is complex due to the presence of multiple phases, multiple monomers, radical species, and other ingredients, an extensive reaction and particle formation mechanism, and the possibility of many modes of reactor operation. 

We begin the discussion of EPM by elaborating on this physical picture. Figure 1 shows a typical emulsion CSTR reactor and polymerization recipe. The magnified portion of the latex shows the various phases and the major species involved. The latex consists of monomers, water, surfactant, initiator, chain transfer agent, and added electrolyte. We used the mechanism for particle formation as described in Feeney et al. (8-9) and Hansen and Ugelstad (2). We have not found it necessary to invoke the micellar entry theory 2, 2/ 6./ 11/ 12/ 14. 

---