Polystyrene-based amine polymers

As for the solid support, several polymer-supported amines were tested (Fig. 2). For either the pyrazole and isoxazole synthesis, the best results were given by aniline-functionalized cellulose, which has also the advantage of a relatively low cost. For the 2-aminopyrimidine library, polystyrene-based piperazine and piperidine gave products with a much higher purity compared with other secondary non-cyclic or primary amines, hi both cases, the resins could be reused for up to four times before degradation in their behavior was observed. This reusability could be further enhanced (up to 10 cycles for cellulose-based aniline) when the microwave-assisted protocols were used. 

Polymer-supported triphenylphosphine ditriflate (37) has been prepared by treatment of polymer bound (polystyrene-2% divinylbenzene copolymer resin) triphenylphosphine oxide (36) with triflic anhydride in dichloromethane, the structure being confirmed by gel-phase 31P NMR [54, 55] (Scheme 7.12). This reagent is effective in various dehydration reactions such as ester (from primary and secondary alcohols) and amide formation in the presence of diisopropylethylamine as base, the polymer-supported triphenylphosphine oxide being recovered after the coupling reaction and reused. Interestingly, with amide formation, the reactive acyloxyphosphonium salt was preformed by addition of the carboxylic acid to 37 prior to addition of the corresponding amine. This order of addition ensured that the amine did not react competitively with 37 to form the unreactive polymer-sup-ported aminophosphonium triflate. 

Chemistry Polyurethane is produced by the reaction of a polyol with an diisocyanate (or in some instances a polyisocyanate) in the presence of catalysts. The polyols of choice are poly(propylene glycol), block copolymers of ethylene oxide (10-15%) with propylene oxide, or the newer polymer polyols (based on polymers such as polystyrene or styrene-acrylonitrile copolymer). Polyester diols such as polycaprolactone diol can be used in place of the polyether polyol in this reaction. The isocyanate of choice is a mixture of the 2,4 and 2,6 isomers of tolylene di-isocyanate in the ratio of 80 20, generally referred to as 80 20TDI. Other isocyanates such as diphenylmethane di-isocyanate (MDI), hexamethylene di-isocyanate (HMDI), and isophorone di-isocyanate (IPDI) are also used. A tin-based or amine catalyst is used to promote the reaction. Given the wide choice of reactants available, the reaction can yield foams with a range of different mechanical and thermal characteristics. 

Antistatic polystyrenes have been developed in terms of additives or coatings to minimise primarily dust collecting problems in storage (see Antistatic agents). Large Hsts of commercial antistatic additives have been pubhshed (41). For styrene-based polymers, alkyl and/or aryl amines, amides, quaternary ammonium compounds, anionics, etc, are all used. 

Some commercial durable antistatic finishes have been Hsted in Table 3 (98). Early patents suggest that amino resins (qv) can impart both antisHp and antistatic properties to nylon, acryUc, and polyester fabrics. CycHc polyurethanes, water-soluble amine salts cross-linked with styrene, and water-soluble amine salts of sulfonated polystyrene have been claimed to confer durable antistatic protection. Later patents included dibydroxyethyl sulfone [2580-77-0] hydroxyalkylated cellulose or starch, poly(vinyl alcohol) [9002-86-2] cross-linked with dimethylolethylene urea, chlorotria2ine derivatives, and epoxy-based products. Other patents claim the use of various acryUc polymers and copolymers. Essentially, durable antistats are polyelectrolytes, and the majority of usehil products involve variations of cross-linked polyamines containing polyethoxy segments (92,99—101). 

Secondary amines, such as pyrrolidine, must be alkylated with care too polar a solvent leads to participation of a second nearby polymer-bound alkylant in the formation of a quaternary ammonium salt, along with the desired immobilized trialkyl amine. The exception, as seen above, is diisopropylamine, which refuses to displace tosylate even in the refluxing pure amine, or in hot dimethyl-formamide or other polar solvent, while metal diisopropylamide is notorious as a powerful non-nucleophilic base. However, carboxamide is not difficult to form from (carboxymethyl)polystyrene, again using toluenesulfonyl chloride as condensing agent this can then be reduced to (diisopropyl-ethylaminoethyl)polystyrene, which is of interest as a polymer-bound non-nucleophilic base. ... 

In a related application, polyelectrolyte microgels based on crosslinked cationic poly(allyl amine) and anionic polyfmethacrylic acid-co-epoxypropyl methacrylate) were studied by potentiometry, conductometry and turbidimetry [349]. In their neutralized (salt) form, the microgels fully complexed with linear polyelectrolytes (poly(acrylic acid), poly(acrylic acid-co-acrylamide), and polystyrene sulfonate)) as if the gels were themselves linear. However, if an acid/base reaction occurs between the linear polymers and the gels, it appears that only the surfaces of the gels form complexes. Previous work has addressed the fundamental characteristics of these complexes [350, 351] and has shown preferential complexation of cationic polyelectrolytes with crosslinked car-boxymethyl cellulose versus linear CMC [350], The departure from the 1 1 stoichiometry with the non-neutralized microgels may be due to the collapsed nature of these networks which prevents penetration of water soluble polyelectrolyte. 

In an opposite manner to bases such as 1 and 2 in terms of reactivity, polymer-supported tosyl chloride equivalent 14 is able to capture alcohols as polymer-bound sulfonates 15, which are released as secondary amines, sulfides and alkylated imidazoles with primary amines, thiols and imidazoles as nucleophiles in a substitution process (Scheme 6) [24]. This technique has further been extended for the preparation of tertiary amines [25] and esters [26]. Excess of amine was scavenged by polymer-supported isocyanate 16 [27, 28] while excess of carboxylic acid was removed by treatment with aminomethylated polystyrene 17. 

Subsequently D Alello developed the polystyrene-hased resin in 1944 (4). Two years later, polystyrene anion-exchange resins made hy chloromethylation and amination of the matrix were produced. Four principal classes of ion-exchange resins were commercially availahle by the 1950s. These are the strong-acid, strong-hase, and weak-hase resins derived from styrene-divinylbenzene copolymers, and the weak-acid resins derived from cross-linked acrylics. To this day, the most widely used ion exchangers are synthetic organic polymer resins based on styrene- or acrylic-acid-type monomers as described by D Alelio in U.S. Patent 2,3666,007. 

A common type of weak-base exchanger uses the same polystyrene-DVB polymer but contains tertiary amine groups (Figure 8.5) [6]. 

---