Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Polymerization, anionic cationic, vinyl monomers

The addition polymerization of a vinyl monomer CH2=CHX involves three distinctly different steps. First, the reactive center must be initiated by a suitable reaction to produce a free radical or an anion or cation reaction site. Next, this reactive entity adds consecutive monomer units to propagate the polymer chain. Finally, the active site is capped off, terminating the polymer formation. If one assumes that the polymer produced is truly a high molecular weight substance, the lack of uniformity at the two ends of the chain—arising in one case from the initiation, and in the other from the termination-can be neglected. Accordingly, the overall reaction can be written... [Pg.14]

The importance of the electrophilic character of the cation in organo-alkali compounds has been discussed by Morton (793,194) for a variety of reactions. Roha (195) reviewed the polymerization of diolefins with emphasis on the electrophilic metal component of the catalyst. In essence, this review willattempt to treat coordination polymerization with a wide variety of organometallic catalysts in a similar manner irrespective of the initiation and propagation mechanisms. The discussion will be restricted to the polymerization of olefins, vinyl monomers and diolefins, although it is evident that coordinated anionic and cationic mechanisms apply equally well to alkyl metal catalyzed polymerizations of polar monomers such as aldehydes and ketones. [Pg.540]

In homogeneous anionic polymerizations of simple vinyl monomers, steric placement is also temperature-dependent, just as it is in cationic polymerizations. Syndiotactic placement is favored in polar solvents at low temperature. In nonpolar solvents, however, isotactic placement predominates at the same temperatures. Here, too, this results mainly from the degree of association with the counterion. [Pg.113]

Monomers containing rings or double bonds can be polymerized by chain polymerization, which is also known as addition polymerization. (It should be contrasted with Step polymerization.) The chain reaction involves the sequential steps of initiation, propagation and termination. Initiation is the process by which active centres are formed these may be free radicals, anions or cations. The free radical chain polymerization of a vinyl monomer is illustrated below. [Pg.68]

Major commercial synthetic specialty polymers are made by chain-growth polymerization of functionalized vinyl monomers, carbonyl monomers, or strained ring compounds. Depending on monomer structure, the polymerization may be initiated free radically, anionically, or cationically. Copolymers or terpolymers with random, alternating, block, or graft sequences can be prepared under appropriate reaction conditions. There are numerous mediods used to prepare specialty polymers in the research laboratory. However, only a few are of commercial interest. Of particular commercial interest is synthesis of specialty polymers in solutions, dispersions, suspensions, or emulsions. [Pg.6]

A cationic or anionic hydrophilic vinyl monomer is polymerized with a hydrophobic vinyl monomer. This polymer is thinly coated onto a substrate using an appropriate solvent to make a tvidely used sensor as shown in Fig. 2. For example,a copolymer made of a vinyl monomer and reactive cationic monomer is coated on a substrate and has been made into... [Pg.1357]

The general conclusion is that polymerization of chiral vinyl monomers takes place without appreciable racemization in the presence of different initiators that is, radical, cationic or anionic. Substantiation of this conclusion derives from C—NMR data on poly-a-olefins [28], the technique providing a very useful nondestructive method for testing configurational features of macromolecular compounds. [Pg.88]

It might be noted that most (not all) alkenes are polymerizable by the chain mechanism involving free-radical intermediates, whereas the carbonyl group is generally not polymerized by the free-radical mechanism. Carbonyl groups and some carbon-carbon double bonds are polymerized by ionic mechanisms. Monomers display far more specificity where the ionic mechanism is involved than with the free-radical mechanism. For example, acrylamide will polymerize through an anionic intermediate but not a cationic one, A -vinyl pyrrolidones by cationic but not anionic intermediates, and halogenated olefins by neither ionic species. In all of these cases free-radical polymerization is possible. [Pg.349]

The kinds of vinyl monomers which undergo anionic polymerization are those with electron-withdrawing substituents such as the nitrile, carboxyl, and phenyl groups. We represent the catalysts as AB in this discussion these are substances which break into a cation (A ) and an anion (B ) under the conditions of the reaction. In anionic polymerization it is the basic anion which adds across the double bond of the monomer to form the active center for polymerization ... [Pg.404]

Radical copolymerization is used in the manufacturing of random copolymers of acrylamide with vinyl monomers. Anionic copolymers are obtained by copolymerization of acrylamide with acrylic, methacrylic, maleic, fu-maric, styrenesulfonic, 2-acrylamide-2-methylpro-panesulfonic acids and its salts, etc., as well as by hydrolysis and sulfomethylation of polyacrylamide Cationic copolymers are obtained by copolymerization of acrylamide with jV-dialkylaminoalkyl acrylates and methacrylates, l,2-dimethyl-5-vinylpyridinum sulfate, etc. or by postreactions of polyacrylamide (the Mannich reaction and Hofmann degradation). Nonionic copolymers are obtained by copolymerization of acrylamide with acrylates, methacrylates, styrene derivatives, acrylonitrile, etc. Copolymerization methods are the same as the polymerization of acrylamide. [Pg.69]

Anionic polymerization is better for vinyl monomers with electron withdrawing groups that stabilize the intermediates. Typical monomers best polymerized by anionic initiators include acrylonitrile, styrene, and butadiene. As with cationic polymerization, a counter ion is present with the propagating chain. The propagation and the termination steps are similar to cationic polymerization. [Pg.308]

Synthetic polymers can be classified as either chain-growth polymen or step-growth polymers. Chain-growth polymers are prepared by chain-reaction polymerization of vinyl monomers in the presence of a radical, an anion, or a cation initiator. Radical polymerization is sometimes used, but alkenes such as 2-methylpropene that have electron-donating substituents on the double bond polymerize easily by a cationic route through carbocation intermediates. Similarly, monomers such as methyl -cyanoacrylate that have electron-withdrawing substituents on the double bond polymerize by an anionic, conjugate addition pathway. [Pg.1220]

Our investigations agree with arguments in earlier articles by other authors, namely that empirical reactivity indices provide the best correlation with the goal values of the cationic polymerization (lg krel, DPn, molecular weight). On the other hand, the quantum chemical parameters are often based on such simplified models that quantitative correlations with experimental goal values remain unsatisfactory 84,85>. But HMO calculations for vinyl monomers show, that it is possible to determine intervals of values for quantum chemical parameters which reflect the anionic and cationic polymerizability 72,74) (see part 4.1.1) as well as grades of the reactivity (see part 3.2). [Pg.195]

The situation is quite different in chain polymerization where an initiator is used to produce an initiator species R with a reactive center. The reactive center may be either a free radical, cation, or anion. Polymerization occurs by the propagation of the reactive center by the successive additions of large numbers of monomer molecules in a chain reaction. The distinguishing characteristic of chain polymerization is that polymer growth takes place by monomer reacting only with the reactive center. Monomer does not react with monomer and the different-sized species such as dimer, trimer, tetramer, and n-trier do not react with each other. By far the most common example of chain polymerization is that of vinyl monomers. The process can be depicted as... [Pg.7]

Whether a vinyl monomer polymerizes by radical, anionic, or cationic initiators depends on the inductive and resonance characteristics of the substituent(s) present. The effect of the... [Pg.200]

In addition to traditional radical initiated addition polymerizations, cation and/or anion catalyzed addition polymerizations are of great commercial importance, since PE, PP and PS are most frequently produced using this type of polymerization technique (Table 5). In addition to the vinyl monomers, vinyli-dene monomers, in which neither R nor R is hydrogen, can form commercially important polymers. PMMA is a typical example of this type of thermoplastics. [Pg.17]

The various kinds of growing species differ not only in their propagation but also in their stereochemical preferences. Professor Hogen-Esch will review this subject in his talk on anionic oligomerization of some vinyl monomer, and mechanisms of anionic, stereospecific polymerization of 2-vinyl pyridine will be discussed by Dr. Fontanille. In this context, the interesting paper of Schuerch et al.(12) deserves attention. Their work clearly reveals the effect of cation solvation upon the mode of monomer s approach to the growing centers. [Pg.5]

So far as vinyl monomers are concerned, ionic propagation proceeds with carbonium ions (cationic polymerization) or carbanions (anionic polymerization) at the chain ends. The study of the initiation process of radiation-induced ionic polymerization seeks to elucidate how these ions are formed from the primary ionic intermediates. Possible reactions... [Pg.402]

In contrast to the slow step-reaction polymerizations, chain-reaction polymerizations are fairly rapid.14 Chain-reaction polymerizations (often referred to as addition polymerizations) require the presence of an initiator for polymerization to occur. Initiation can occur by a free radical, an anionic, or a cationic species, which open the double bond of a vinyl monomer and the reaction proceeds as shown in Fig. 15.11 where may be a radical,... [Pg.631]


See other pages where Polymerization, anionic cationic, vinyl monomers is mentioned: [Pg.117]    [Pg.572]    [Pg.115]    [Pg.29]    [Pg.1]    [Pg.625]    [Pg.320]    [Pg.541]    [Pg.283]    [Pg.61]    [Pg.45]    [Pg.135]    [Pg.143]    [Pg.179]    [Pg.26]    [Pg.225]    [Pg.372]    [Pg.378]    [Pg.703]    [Pg.112]    [Pg.320]    [Pg.5]    [Pg.1446]    [Pg.5]    [Pg.65]    [Pg.78]    [Pg.562]    [Pg.118]   
See also in sourсe #XX -- [ Pg.4 ]




SEARCH



Anionic cationic

Anionic-cationic polymerization

Cation anion

Cationic polymerization

Cationic polymerization polymerizations

Monomer cation-anionic

Monomer, cationic

Monomers, polymerization

Polymerization vinylic

Vinyl anions

Vinyl cations

Vinyl monome

Vinyl monomer

Vinyl monomers cationic polymerization

Vinyl monomers polymerization

Vinyl polymerization

Vinylic anions

Vinylic cations

Vinylic monomers

© 2024 chempedia.info