Polymerization, anionic cationic

Synthesized polymer hybrids based on polyolefins are expected to possess the properties of each polymer segment. Several methodologies for the preparation of polyolefin hybrids have been reported in recent papers [27,28]. In particular, processes such as radical, anionic, cationic polymerizations and... 

Catalysis has also had a major impact on the functional and specialty chemicals businesses, providing lower cost routes and higher performance materials than would have otherwise been possible. Major examples are from polymer syntheses including Ziegler-Natta, anionic, cationic polymerization processes, for formation of polyolefins, ABS resins, polyesters and other synthetic materials. Future materials areas include high temperature composites, electronic materials and conducting organics. 

Anionic-cationic polymerization n. A method of preparing multi-block copolymers using a combination of anionic and cationic) (ion coupling) methods. 

Ionic polymerizations are of two types cationic and anionic. Cationic polymerizations are initiated using electrophiles, whereas anionic polymerizations are often initiated by electron-deficient species such as organolithium compounds. The propagation steps can be summarized... 

Linear polysiloxane can be synthesized by both anionic and cationic polymerizations of cyclic siloxanes such as hexamethylcyclotrisiloxane (n = 3) and octamethyl cyclotetrasiloxane (n = 4). Anionic polymerization is initiated by hydroxide, alkoxides, phenolates, silanolates and siloxoano-lates. The active species in the polymerization is the silanolate anion. Cationic polymerization is initiated by strong protonic acids such as sulfuric acid, trifluoromethane sulfonic acid and trifluoro-acetic acid (equation 53). Both the anionic and the cationic species undergo backbiting reactions during polymerization, such that an equilibrium exists between linear chains and rings. ... 

Block copolymers of methylthiirane with thiirane or with 2,2-dimethylthiirane have also been obtained by sequential polymerizations initiated in the first phase by 2-naphthylsulfonylmethylene anions.Cationic polymerization has found use in the conversion of 3,3-dimethylthietane to SH-ended oligomers which could be coupled with hydroxyl-ended POE chains by reaction with a diisocyanate, but attempts to obtain block polymers of this thietane by direct initiation with cationic polystyrene were not successful. 

My faculty colleagues of the Institute also bring great expertise in the areas of anionic, cationic, and radical polymerization to the transformation of low-molecular-weight hydrocarbons into macromole-... 

Ionic polymerizations, whether anionic or cationic, should not be judged to be unimportant merely because our treatment of them is limited to two sections in this text. Although there are certain parallels between polymerizations which occur via free-radical and ionic intermediates, there are also numerous differences. An important difference lies in the more specific chemistry of the ionic mechanism. While the free-radical mechanism is readily discussed in general terms, this is much more difficult in the ionic case. This is one of the reasons why only relatively short sections have been allotted to anionic and cationic polymerizations. The body of available information regarding these topics is extensive enough to warrant a far more elaborate treatment, but space limitations and the more specific character of the material are the reasons for the curtailed treatment. 

Just as anionic polymerizations show certain parallels with the free-radical mechanism, so too can cationic polymerization be discussed in terms of the same broad outline. There are some differences from the anionic systems, however, so the fact that both proceed through ionic intermediates should not be overextended. 

On the basis of these observations, criticize or defend the following proposition Regardless of the monomer used, zero-order Markov (Bernoulli) statistics apply to all free radical, anionic, and cationic polymerizations, but not to Ziegler-Natta catalyzed systems. 

Polyacetaldehyde, a mbbery polymer with an acetal stmcture, was first discovered in 1936 (49,50). More recentiy, it has been shown that a white, nontacky, and highly elastic polymer can be formed by cationic polymerization using BF in Hquid ethylene (51). At temperatures below —75° C using anionic initiators, such as metal alkyls in a hydrocarbon solvent, a crystalline, isotactic polymer is obtained (52). This polymer also has an acetal [poly(oxymethylene)] stmcture. Molecular weights in the range of 800,000—3,000,000 have been reported. Polyacetaldehyde is unstable and depolymerizes in a few days to acetaldehyde. The methods used for stabilizing polyformaldehyde have not been successful with poly acetaldehyde and the polymer has no practical significance (see Acetalresins). 

Polymerization. In the absence of inhibitors, acrolein polymerizes readily in the presence of anionic, cationic, or free-radical agents. The resulting polymer is an insoluble, highly cross-linked soHd with no known commercial use. 

The surfactants used in the emulsion polymerization of acryhc monomers are classified as anionic, cationic, or nonionic. Anionic surfactants, such as salts of alkyl sulfates and alkylarene sulfates and phosphates, or nonionic surfactants, such as alkyl or aryl polyoxyethylenes, are most common (87,98—101). Mixed anionic—nonionic surfactant systems are also widely utilized (102—105). 

For continuing polymerization to occur, the ion pair must display reasonable stabiUty. Strongly nucleophilic anions, such as C/ , are not suitable, because the ion pair is unstable with respect to THE and the alkyl haUde. A counterion of relatively low nucleophilicity is required to achieve a controlled and continuing polymerization. Examples of anions of suitably low nucleophilicity are complex ions such as SbE , AsF , PF , SbCf, BE 4, or other anions that can reversibly coUapse to a covalent ester species CF SO, FSO, and CIO . In order to achieve reproducible and predictable results in the cationic polymerization of THE, it is necessary to use pure, dry reagents and dry conditions. High vacuum techniques are required for theoretical studies. Careful work in an inert atmosphere, such as dry nitrogen, is satisfactory for many purposes, including commercial synthesis. 

The chemistry of polymerization of the oxetanes is much the same as for THE polymerization. The ring-opening polymerization of oxetanes is primarily accompHshed by cationic polymerization methods (283,313—318), but because of the added ring strain, other polymerization techniques, eg, iasertion polymerization (319), anionic polymerization (320), and free-radical ring-opening polymerization (321), have been successful with certain special oxetanes. 

Cationic Polymerization. For decades cationic polymerization has been used commercially to polymerize isobutylene and alkyl vinyl ethers, which do not respond to free-radical or anionic addition (see Elastomers, synthetic-BUTYLRUBBEr). More recently, development has led to the point where living cationic chains can be made, with many of the advantages described above for anionic polymerization (27,28). 

There are two problems in the manufacture of PS removal of the heat of polymeriza tion (ca 700 kj /kg (300 Btu/lb)) of styrene polymerized and the simultaneous handling of a partially converted polymer symp with a viscosity of ca 10 mPa(=cP). The latter problem strongly aggravates the former. A wide variety of solutions to these problems have been reported for the four mechanisms described earlier, ie, free radical, anionic, cationic, and Ziegler, several processes can be used. Table 6 summarizes the processes which have been used to implement each mechanism for Hquid-phase systems. Free-radical polymerization of styrenic systems, primarily in solution, is of principal commercial interest. Details of suspension processes, which are declining in importance, are available (208,209), as are descriptions of emulsion processes (210) and summaries of the historical development of styrene polymerization processes (208,211,212). 

Polymerization Reactions. The polymerization of butadiene with itself and with other monomers represents its largest commercial use. The commercially most important polymers are styrene—butadiene mbber (SBR), polybutadiene (BR), styrene—butadiene latex (SBL), acrylonittile—butadiene—styrene polymer (ABS), and nittile mbber (NR). The reaction mechanisms are free-radical, anionic, cationic, or coordinate, depending on the nature of the initiators or catalysts (194—196). 

Cationic polymerization with Lewis acids yields resinous homopolymers containing cycHc stmctures and reduced unsaturation (58—60). Polymerization with triethyl aluminum and titanium tetrachloride gave a product thought to have a cycHc ladder stmcture (61). Anionic polymeriza tion with lithium metal initiators gave a low yield of a mbbery product. The material had good freeze resistance compared with conventional polychloroprene (62). 

The most important reaction with Lewis acids such as boron trifluoride etherate is polymerization (Scheme 30) (72MI50601). Other Lewis acids have been used SnCL, Bu 2A1C1, Bu sAl, Et2Zn, SO3, PFs, TiCU, AICI3, Pd(II) and Pt(II) salts. Trialkylaluminum, dialkylzinc and other alkyl metal initiators may partially hydrolyze to catalyze the polymerization by an anionic mechanism rather than the cationic one illustrated in Scheme 30. Cyclic dimers and trimers are often products of cationic polymerization reactions, and desulfurization of the monomer may occur. Polymerization of optically active thiiranes yields optically active polymers (75MI50600). 

---