Polyhydroxy compounds

Nacconate 100 A lachrymatory liquid b.p. 25l°C. Manufactured from phosgene and 2,4-diaminotoJuene. Used for preparing polyurethane foams and other elastomers by reaction with polyhydroxy compounds. Produces skin irritation and causes allergic eczema and bronchial asthma. 

All colourless solids, which decompose on heating and therefore have no definite m.p.s. All insoluble in ether (like most polyhydroxy-compounds). All except starch are soluble in water and have a sweet taste. Starch as ordinarily supplied is insoluble in... 

The melting points of these esters are usually much lower than those of the corresponding 3 5 dinitrobenzoates their preparation, therefore, offers no advantages over the latter except for alcohols of high molecular weight and for polyhydroxy compounds. The reagent is, however, cheaper than 3 5 dinitrobenzoyl chloride it hydrolyses in the air so that it should either be stored under light petroleum or be prepared from the acid, when required, by the thionyl chloride or phosphorus pentachloride method. 

The experimental technique is similar to that given under Aromatic Amines, Section IV,100,2. The following alternative method may also be used. Mix together 0 -5-0 - 8 ml. of the polyhydroxy compound, 5 ml. of pyridine and 2 -5 ml. of redistilled benzoyl chloride in a 50 ml. flask. 

Enantiomerically pure tetroses, pentoses, and hexoses have been synthesized by the following reaction sequence (A.W.M. Lee, 1982 S.Y. Ko, 1983), which is useful as a repetitive two-carbon hotnologi-.ation in total syntheses of higher monosaccharides and other polyhydroxy compounds (1) Wittig reaction of a protected hydroxy aldehyde with (triphenylphosphor-... 

Partial ethers of polyhydroxy compounds may be named (1) by substitutive nomenclature or (2) by stating the name of the polyhydroxy compound followed by the name of the etherifying radical(s) followed by the word ether. For example. 

Reactions with Alcohols, Mercaptans, and Phenols. Alcohols add readily to acetaldehyde in the presence of trace quantities of mineral acid to form acetals eg, ethanol and acetaldehyde form diethyl acetal [105-57-7] (65). Similarly, cycHc acetals are formed by reactions with glycols and other polyhydroxy compounds eg, ethylene glycol [107-21-1] and acetaldehyde give 2-methyl-1,3-dioxolane [497-26-7] (66) ... 

Traces of formaldehyde, present in neat end-capped polymer or produced by processing polymer under abusive conditions, detract from polymer stabihty. Commercial resins typically contain formaldehyde scavengers. Nitrogen compounds, especially amines and amides, epoxies, and polyhydroxy compounds, are particularly efficacious scavengers. 

Hydrogen Chloride-Organic Compound Systems. The solubihty of hydrogen chloride in many solvents follows Henry s law. Notable exceptions are HCl in polyhydroxy compounds such as ethylene glycol (see Glycols), which have characteristics similar to those of water. Solubility data of hydrogen chloride in various organic solvents are Hsted in Table 10. 

A number of complex derivatives of antimony pentoxide with polyhydroxy compounds have been iavestigated as dmgs. The most important of these substances is known as antimony sodium gluconate [16037-91-5] C22H2Q02ySb2 9H20 3Na, which is prepared by the reaction of antimony pentoxide, gluconic acid, and sodium hydroxide (53). 

The apparent acid strength of boric acid is increased both by strong electrolytes that modify the stmcture and activity of the solvent water and by reagents that form complexes with B(OH) 4 and/or polyborate anions. More than one mechanism may be operative when salts of metal ions are involved. In the presence of excess calcium chloride the strength of boric acid becomes comparable to that of carboxyUc acids, and such solutions maybe titrated using strong base to a sharp phenolphthalein end point. Normally titrations of boric acid are carried out following addition of mannitol or sorbitol, which form stable chelate complexes with B(OH) 4 in a manner typical of polyhydroxy compounds. EquiUbria of the type ... 

Acetalation. As polyhydroxy compounds, carbohydrates react with aldehydes and ketones to form cycHc acetals (1,13). Examples are the reaction of D-glucose with acetone and a protic or Lewis acid catalyst to form l,2 5,6-di-0-isoprop5lidene-a-D-glucofuranose [582-52-5] and its reaction with benzaldehyde to form 4,6-0-benzyhdene-D-glucopyranose [25152-90-3]. The 4,6-0-(l-carboxyethyhdine) group (related to pymvic acid) occurs naturally in some polysaccharides. 

Possible uses for these polyhydroxy compounds include the preparation of alkyd-type resins with polybasic acids, the formation of ester plasticizers, and the preparation of surface-active agents. 

Reaction of polyhydroxy compounds with polybasic acids gives rise to condensation polymers containing ester (—COO—) groups. Because of the presence of these groups such polycondensates are known as polyesters and find use in such diverse applications as fibres, surface coatings, plasticisers, rubbers and laminating resins. These materials are discussed in detail in Chapter 25. 

By reaction of polyhydroxy compounds with a carbonic acid derivative, a series of related polymers may be produced with carbonate (—0 C0 0—) linkages, the polymers being referred to as polycarbonates. Carbonic acid, C0(0H)2, itself does not exist in the free state but by means of ester exchange Figure 20.1) (1) and phosgenation techniques (II) it is possible to produce useful products. 

Unless the hydroxyl groups have such proximity that cyclisation takes place, polycarbonates will normally be produced whenever phosgene or a carbonate ester is reacted with a polyhydroxy compound. This means that a very large range of polycarbonate resins are possible and in fact many hundreds have been prepared. 

Condensation of polyhydroxy compounds with polybasic acids, e.g. a glycol with a dicarboxylic acid ... 

Glycidyl ether resins are formed by reaction of epichlorohydrin with polyhydroxy compounds. In addition to the dominant use of bis-phenol A several other polyhydroxy compounds have been used. In particular there has been... 

Although the first polyurethanes were similar to that shown above, several polymers currently used contain many linkages in addition to the urethane group. Because of this the term polyurethane is now generally extended to cover all the complex reaction products of isocyanates and polyhydroxy compounds (the latter frequently known in this context as polyols). 

Trehalose is particularly well-suited for this purpose and has been shown to be superior to other polyhydroxy compounds, especially at low concentrations. Support for this novel idea comes from studies by P. A. Attfield, which show that trehalose levels in the yeast Saccharomyces cerevisiae increase significandy during exposure to high salt and high growth temperatures—the same conditions that elicit the production of heat-shock proteins ... 

The effect of polyhydroxy compounds has been explained on the basis of the formation of 1 1 and 1 2-mole ratio complexes between the hydrated borate ion and 1,2- or 1,3-diols ... 

Zinc carbonate reacts with epoxide to form zinc alkoxide, which in turn reacts with carbon dioxide to regenerate zinc carbonate. The most effective catalyst systems were the reaction products between diethylzinc and polyhydroxy compounds such as water or pdyhydric phenols243,244. This copolymer is interesting as a biodegradable elastomer248. ... 

Figure 17-3. Modifiers for polyhydroxy compounds, shown for dextrose as the model compound.

Figure 17-14. Formation of complexes of boric acid with glycerol. Three hydroxyl units form an ester and one unit forms a complex bond. Here a proton will be released that lowers the pH. The scheme is valid also for polyhydroxy compounds. In this case, two polymer chains are connected via such a link.

Smaller aldehydes form cyclic acetal-type oligomers readily in aqueous conditions.60 Diols and polyols also form cyclic acetals with various aldehydes readily in water, which has been applied in the extraction of polyhydroxy compounds from dilute aqueous solutions.61 E in water was found to be an efficient catalyst for chemoselective protection of aliphatic and aromatic aldehydes with HSCH2CH2OH to give 1,3-oxathiolane acetals under mild conditions (Eq. 5.7).62... 

Most proteins are not sufficiently stable in aqueous solution to allow formulation as a sterile solution. Instead, the protein is freeze-dried and reconstituted before use. Development of a freeze-dried protein formulation often requires special attention to the details of the freezing process (potential pH shifts and ionic strength increase with freezing) as well as to potential loss of activity with drying. Formulation additives, such as sugars and polyhydroxy compounds, are often useful as cryoprotectants and lyoprotectants. Residual moisture may also be critical to the stability of the dried preparation [33],... 

Gorin, P.A.J. and Mazurek, M. "Carbon 13 Resonance Spectroscopic Studies on the Formation of Borate and Diphenylborinate Complexes of Polyhydroxy Compounds," Can. J. Chem. Vol. 51, 1973, pages 3277 3286. 

Mills, J.A. "Association of Polyhydroxy Compounds with Cations in Solution," Biochem. Biophvs. Res. Commun.. 1961/62, 6(6), 418 21. 

---