Polyester vinyl ester

Many different thermosetting polymers are used in pultmsion, eg, polyester, vinyl ester, epoxy, and urethane. Reinforcements must be in a continuous form such as rovings, tows, mats, fabrics, and tapes. Glass fibers are the low cost, dominant composition, but aramid and carbon fibers are also used. 

The typical resin systems include thermoset polyesters, vinyl esters, epoxies, polymi-dies, bismaleimide, and phenolics. Thermoplastics are also finding their way into filament winding. Wet thermoset filament winding requires a resin with viscosity in the range of 1000-3000 cpoise. Resin components are chosen on the basis of pot life, winding temperature, viscosity, gel time, and cure time. 

Common to all reinforced plastics are two ingredients, resin and reinforcement. Resin is an oiganic material, usually of high molecular weight, that can be molded and set into a final shape. Resins are of two basic types. Thermoplastic resins soften upon heating, are shaped in a mold, and retain that shape when cooled. Common examples are nylon, polyethylene, polypropylene, and polycarbonate. Thermosetting resins are placed in a mold and cured by the use of a catalyst, heat, or both, until they harden in the shape of the mold. Common examples are polyester, vinyl ester, epoxies, phenolics, and p olyure thanes. 

There are two types of cure reactions of thermosetting resins step (e.g., epoxies, phenolics, urethanes) and chain (e.g., unsaturated polyesters, vinyl esters, acrilates) polymerizations. In the first type, the size of the polymer chain increases because of the linking of the oligomers (e.g., monomers, dimers, etc.) to themselves. Short chains can be linked to long ones in a condensation reaction. In the second case, the size of the polymer chain increases because of... 

Matrix materials for commercial composites are mainly liquid thermosetting resins such as polyesters, vinyl esters, epoxy resins, and bismaleimide resins. Thermoplastic composites are made from polyamides, polyether ether ketone (PEEK), polyphenylene sulfide (PPS), polysulfone, polyetherim-ide (PEI), and polyamide-imide (PAI). 

The most common advanced composites are made of thermosetting resins, such as epoxy polymers (the most popular singlematrix material), polyesters, vinyl esters, polyurethanes, polyimids, cianamids, bismaleimides, silicones, and melamine. Some of the most widely used thermoplastic polymers are polyvinyl chloride (PVC), PPE (poly[phenylene ether]), polypropylene, PEEK (poly [etheretherketone]), and ABS (acrylonitrile-butadiene-styrene). The precise matrix selected for any given product depends primarily on the physical properties desired for that product. Each type of resin has its own characteristic thermal properties (such as melting point... 

Organic linings such as polyesters, vinyl esters or fluoroelastomers may resist wet acid condensates at low temperatures but will not accept higher temperatures where a semi-refractory is needed. 

Mortars used in the past have primarily been composed of Portland cement, silicates, and litharge and glycerine. Except for Portland cement, these traditional materials have generally been replaced by resin mortars utilizing epoxy, polyester, vinyl ester and furan resins. 

The matrix is considered to be the binder for the microspheres. Typical matrix materials include (a) thermosetting resins such as epoxy resins, unsaturated polyesters, vinyl esters, phenolics, polyurethanes, and silicones (b) thermoplastic resins such as polyethylene, polystyrene, polyvinyl chloride (c) asphalt and (d) gypsiun and cement. 

The matrix resins for foamed composites include rigid pol)ruretha-nes, unsaturated polyesters, vinyl esters, and their hybrid resins, such as, unsaturated polyester-urethane hybrid resins and vinyl ester-urethane hybrid resins. The reinforcing fibers include glass fibers, carbon fibers, and organic fibers such as polyamide fiber (Kevlar, DuPont), polyamide-... 

Aqualease. [Gemge Mann] Silicone emulsions release scents for casting molds, cast urediane elastomer and integral skin urethane foams, epoxies, filled polyester, vinyl ester resins. 

Chempruf. [Atlas Minerals Chem.] Epoxy, polyester, vinyl ester, furan linings. 

Dianol . [Akzo] Ethoxylaled bisphenol A diol reactive modifiers for saturatol and unsaturated polyesters, vinyl esters, and polyurethane resin formulations. 

Superox. [Reichhold] Peroxide derivs. catalyst, polymerization initiator for polyester, vinyl ester resins, vinyl monomers. 

RTM is compatible with a variety of thermosetting polymers including polyester, vinyl ester, epoxy, phenolic, modified acrylic, and hybrid polyester-urethane. A convenient typical viscosity of thermoset precursors is in the range of 0.2-0.6 Pa s. The RTM process has the following advantages (i) emissions are lower than in open-mold processes such as spray-up or hand lay-up (ii) it can produce parts faster, as much as 5-20 times faster than open-mold techniques (iii) the mold surface can produce a high quality finish (iv) complex mold shapes can be achieved and... 

Fume handling ducts Spray-up/hand lay-up Gun roving Chopped strand mat Woven roving Polyester Vinyl ester... 

Sucker rods Pultrusion Roving Polyester Vinyl ester... 

Tacky tape is a butyl-based vacuum bag sealant giving high elasticity and tenacity. It has exceptional sealant properties, eliminating the risk of imperfect seals often fi>und in the initial phases of vacuum bag application, so improving the vacuum efficiency and reducing labor. It is suitable for polyester, vinyl ester, and epoxy laminating systems. 

Intrinsically non-flammable polymers are few, but phenolic resins have a good reputation both in Are and smoke performance, which has resulted in their becoming increasingly favoured for reinforced plastics structures, for example, underground transport, where such concerns are greatest. Polyether ether ketone (PEEK) is also a low fire and smoke polymer. Unsaturated polyesters, vinyl esters and epoxy resins bum readily, but modified versions are available with improved behaviour. For example, both bromine and chlorine are used extensively in the form of chlorendic (HET) acid, tetrachlorophthalic anhydride (TCPA) and tetrabromo-phthalic anhydride (TBPA) which can be reacted into the polyester in small quantities and can act as permanent (non-migrating) flame retardants. 

Chem. Descrip. Proprietary resin in aliphatic hydrocarbon solv. blend Uses External mold release for polyester, vinyl ester, and epoxies for open molding, cast polymers, cultured marble, and parts requiring exc. finishes... 

Polymer composites are plastics within which fibres are embedded. The plastic is known as the matrix (resin) and the fibres dispersed witbin it are known as the reinforcement Thermosetting matrix materials include polyester, vinyl ester and epoxy resins. For higher temperature and extreme environments, bismaleimlde, polyimide and phenolic resins are used. Composites can be used to replace metal parts but care must be taken during design. Most engineering materials have similar properties in any direction (called isotropic) where composites have not This can however be offset by arranging the reinforcement layers in varying directions. 

Vinyl ester resins are similar to unsaturated polyester resins in that they are cured by a free radical initiated polymerisation. However, they differ from the polyesters in that the unsaturation is at the ends of the molecule rather than along the polymer chain. Unlike polyesters, vinyl esters show a greater resistance to hydrolysis as well as lower peak exotherm temperatures and less shrinkage upon cure. Cured vinyl ester resins exhibit excellent resistance to acids, bases and solvents. They also show improved strain to failure, toughness and glass transition temperatures over polyesters. They can be used in filament winding, pultrusion, resin injection, vacuum moulding and conventional hand lay-up. 

---