Polyester polyurethanes

As with polyesters, the amidation reaction of acid chlorides may be carried out in solution because of the enhanced reactivity of acid chlorides compared with carboxylic acids. A technique known as interfacial polymerization has been employed for the formation of polyamides and other step-growth polymers, including polyesters, polyurethanes, and polycarbonates. In this method the polymerization is carried out at the interface between two immiscible solutions, one of which contains one of the dissolved reactants, while the second monomer is dissolved in the other. Figure 5.7 shows a polyamide film forming at the interface between an aqueous solution of a diamine layered on a solution of a diacid chloride in an organic solvent. In this form interfacial polymerization is part of the standard repertoire of chemical demonstrations. It is sometimes called the nylon rope trick because of the filament of nylon produced by withdrawing the collapsed film. 

A Methylolhydantoins. l,3-Bis(hydroxymethyl)-5,5-dimethyIhydantoia [6440-58-0] is used extensively as a preservative in cosmetic and industrial appHcations, and carries EPA registration for the industrial segment. It is available in soHd and in aqueous solution forms, including low free formaldehyde versions of the latter. A related derivative, l,3-bis(hydroxyethyl)-5,5-dimethyIhydantoia [26850-24-8] is used in the manufacture of high temperature polyesters, polyurethanes, and coatings, offering improved heat resistance, uv stabiUty, flexibiUty, and adhesion. 

For some years there has been concern at the amount of styrene vapour in workshops preparing reinforced polyester laminates. More recently this has increased interest in polyester-polyurethane hybrids and in the further development of closed moulding and resin transfer moulding techniques as well as greater use of lower styrene levels. 

Figure 27.8. Typical load-deflection curves for (a) latex, (b) flexible PVC, (c) polyester polyurethane (curve C) and polyether polyurethane foams (curve D). Shell Chemical Co.)...

The minimum service temperature is determined primarily by the Tg of the soft phase component. Thus the SBS materials ctm be used down towards the Tg of the polybutadiene phase, approaching -100°C. Where polyethers have been used as the soft phase in polyurethane, polyamide or polyester, the soft phase Tg is about -60°C, whilst the polyester polyurethanes will typically be limited to a minimum temperature of about 0°C. The thermoplastic polyolefin rubbers, using ethylene-propylene materials for the soft phase, have similar minimum temperatures to the polyether-based polymers. Such minimum temperatures can also be affected by the presence of plasticisers, including mineral oils, and by resins if these become incorporated into the soft phase. It should, perhaps, be added that if the polymer component of the soft phase was crystallisable, then the higher would also affect the minimum service temperature, this depending on the level of crystallinity. 

Effect of chain structure on the hydrolysis of polyester polyurethanes... 

Abrasion-resistant duties may involve abrasion in an aqueous phase or abrasion by dry particulate materials. The selection of the polyurethane type is most important to obtain the best results. Polyester-based polyurethanes perform best in dry abrasion due to their low hysteresis properties and excellent resistance to cut initiation and propagation. However, polyester polyurethanes are susceptible to hydrolytic degradation, and therefore polyether polyurethanes are normally used for aqueous abrasion duties. 

Polyester polyurethanes are usually based on a blend of a quasi-prepolymer (polyester/MDl) and a diol/polyester suitable for spray-up operation. An alternative is to use a solvent-containing system using blocked curatives to give an extended pot-life of 2 to 3 hours enabling them to be brush, roller or spray applied. 

A novel chemoenzymatic route to polyester polyurethanes was developed without employing highly toxic isocyanate intermediates. First, diurethane diols were prepared from cyclic carbonates and primary diamines, which were subsequently polymerized with dicarboxylic acids and glycols by using lipase CA as catalyst, yielding the polyurethanes under mild reaction conditions. 

Step polymerization is used to synthesize multiblock copolymeric elastomers (referred to as segmented elastomers). An example is the polyester-polyurethane system produced by the reaction of a diisocyanate with a mixture of macro diol and smallsized diol (Eq. 14). The macro diol (usually referred to as a... 

Thermoplastic elastomeric behavior requires that the block copolymer develop a microheterogeneous two-phase network morphology. Theory predicts that microphase separation will occur at shorter block lengths as the polarity difference between the A and B blocks increases. This prediction is borne out as the block lengths required for the polyether-polyurethane, polyester-polyurethane, and polyether-polyester multiblock copolymers to exhibit thermoplastic elastomeric behavior are considerably shorter than for the styrene-diene-styrene triblock copolymers. 

The nature of the hard domains differs for the various block copolymers. The amorphous polystyrene blocks in the ABA block copolymers are hard because the glass transition temperature (100°C) is considerably above ambient temperature, i.e., the polystyrene blocks are in the glassy state. However, there is some controversy about the nature of the hard domains in the various multiblock copolymers. The polyurethane blocks in the polyester-polyurethane and polyether-polyurethane copolymers have a glass transition temperature above ambient temperature but also derive their hard behavior from hydrogen-bonding and low levels of crystallinity. The aromatic polyester (usually terephthalate) blocks in the polyether-polyester multiblock copolymer appear to derive their hardness entirely from crystallinity. 

The generic name given, in the USA, to stretch fibres based on elastomeric long-chain polyester polyurethanes. Trade names are, e.g., Lycra and Vyrene . 

Polyesters, polyurethanes Polyesters, nylons, polyurethanes Polypropylene, LDPE, PMMA, poly(alpha-methylstyrene) Polybutadienes, polyisoprene... 

Ethylene glycol (EG) has two OH groups so it wiU polymerize as a linear polymer in polyesters, polyurethanes, or polyethers. Ethylene glycol is also water soluble and has a low melting point so it is used in antifreeze. 

From the results presented in this chapter we can conclude that it is feasible to prepare sugar-based polymers analogous to the more qualified technological polymers - polyamides, polyesters, polyurethanes - with an enhanced hydrophilicity and degradability. However, in most cases, the high costs associated with the preparation of the monomers restrict the application of these polymers to biomedical applications and other specialized fields. More readily available monomers and simpler polymerization processes have to be found if sugar-derived polymers should compete with petrochemical-based polymers that are used in domestic applications. 

Another resin application based on the same hyperbranched polyester structure described herein is low-VOC alkyds, which have very low viscosity and high reactivity compared to conventional high-solid alkyds. Other resin structures are unsaturated polyesters, polyurethane dispersions, and epoxides. ... 

Plastics are by far the largest group of polymeric materials being processed by electron beam irradiation. Cross-linking of polyolefins, PVC, polyesters, polyurethanes, fluoropolymers, and fiber-reinforced composites is a common practice. 

Copolymer of styrene and acrylonitrile Copolymer of styrene and butadiene Natural rubber Chlorinated polyethylene Chlorosulfonated polyethylene Polyamides Polyesters Polyurethanes Polysulfones Polyacrylates Polyacrylamides Polydimethylsiloxane Copolymer of vinylidene fluoride and hexafluoropropylene... 

It is useful to examine reticulated foams in the context of their suitability as scaffolds for artificial organ development. Reticulated foams are made in a postprocessing step after polyurethane foams are made. Polyether and polyester polyurethanes are made for reticulation. The major use of the materials is in air filtration where resistance to flow (a mass transport property) is an important requirement. 2005 by CRC Press LLC... 

HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HNS NTO NTO/HMX NTO/HMX NTO/HMX PETN PETN PETN PETN PETN PETN PETN PETN PETN PETN RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX TATB/HMX Cariflex (thermoplastic elastomer) Hydroxy-terminated polybutadiene (polyurethane) Hydroxy-terminated polyester Kraton (block copolymer of styrene and ethylene-butylene) Nylon (polyamide) Polyester resin-styrene Polyethylene Polyurethane Poly(vinyl) alcohol Poly(vinyl) butyral resin Teflon (polytetrafluoroethylene) Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Cariflex (block copolymer of butadiene-styrene) Cariflex (block copolymer of butadiene-styrene) Estane (polyester polyurethane copolymer) Hytemp (thermoplastic elastomer) Butyl rubber with acetyl tributylcitrate Epoxy resin-diethylenetriamine Kraton (block copolymer of styrene and ethylene-butylene) Latex with bis-(2-ethylhexyl adipate) Nylon (polyamide) Polyester and styrene copolymer Poly(ethyl acrylate) with dibutyl phthalate Silicone rubber Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Epoxy ether Exon (polychlorotrifluoroethylene/vinylidine chloride) Hydroxy-terminated polybutadiene (polyurethane) Kel-F (polychlorotrifluoroethylene) Nylon (polyamide) Nylon and aluminium Nitro-fluoroalkyl epoxides Polyacrylate and paraffin Polyamide resin Polyisobutylene/Teflon (polytetrafluoroethylene) Polyester Polystyrene Teflon (polytetrafluoroethylene) Kraton (block copolymer of styrene and ethylene-butylene)... 

Diacetoxy-2-butene. Mitsubishi commercialized a new proces, the acetoxy-lation of 1,3-butadiene, as an alternative to the Reppe (acetylene-formaldehyde) process for the production of l,4-diacetoxy-2-butene. l,4-Diacetoxy-2-butene is tranformed to 1,4-butanediol used in polymer manufacture (polyesters, polyurethanes). Additionally, 1,4-butanediol is converted to tetrahydrofuran, which is an important solvent and also used in polymer synthesis. 

---