Polarizability, hydrocarbons

Polarizable hydrocarbons, such as short-chain arenes (benzene, isopropylbenzene), have been shown to be solubilized in quaternary ammonium solutions initially by absorption at the micelle-water interface, replacing water molecules that may have penetrated into the outer core of the micelle close to the polar heads, but solubilization of additional material is either deep in the palisade layer or located in the inner core of the micelle (Eriksson, 1965). The polarizability of the ji-electron cloud of the aromatic nucleus and its consequent ability to interact with the positively charged quaternary ammonium groups at the micelle-water interface may account for the initial adsorption of these hydrocarbons in that location. In POE nonionics, benzene may be solubilized between the polyoxyethylene chains of the hydrophilic groups (Nakagawa, 1967). 

Polarizability measures the response of an ion or molecule to an electric field and is expressed in units of volume, typically 10 cm or A Polarizability increases with atomic or ionic radius it depends on the effectiveness of nuclear screening and increases as each valence shell is filled. Table 1.4 gives the polarizability values for the second-row atoms and some ions, molecules, and hydrocarbons. Methane is the least polarizable hydrocarbon and polarity increases with size. Polarizability is also affected by hybridization, with ethane > ethene > ethyne and propane > propene > propyne. 

Solubilities of nonfunctional compounds are also enhanced by cosolvents, but the enhancements are more dependent on the cosolvent concentration than the cosolvent functionality (37-38). Nonpolar, polarizable hydrocarbon cosolvents seem more effective than polar cosolvents for enhancing nonfunctional compound solubilities in CO2 (, ), although the differences are small. These differences are negligible in ethane (3S), which is more polarizable than CO2. 

The induced counter-dipole can act in a similar manner to a permanent dipole and the electric forces between the two dipoles (permanent and induced) result in strong polar interactions. Typically, polarizable compounds are the aromatic hydrocarbons examples of their separation using induced dipole interactions to affect retention and selectivity will be given later. Dipole-induced dipole interaction is depicted in Figure 12. Just as dipole-dipole interactions occur coincidentally with dispersive interactions, so are dipole-induced dipole interactions accompanied by dispersive interactions. It follows that using an n-alkane stationary phase, aromatic... 

Alternatively, using a polyethylene glycol stationary phase, aromatic hydrocarbons can also be retained and separated primarily by dipole-induced dipole interactions combined with some dispersive interactions. Molecules can exhibit multiple interactive properties. For example, phenyl ethanol possesses both a dipole as a result of the hydroxyl group and is polarizable due to the aromatic ring. Complex molecules such as biopolymers can contain many different interactive groups. 

Silica gel, per se, is not so frequently used in LC as the reversed phases or the bonded phases, because silica separates substances largely by polar interactions with the silanol groups on the silica surface. In contrast, the reversed and bonded phases separate material largely by interactions with the dispersive components of the solute. As the dispersive character of substances, in general, vary more subtly than does their polar character, the reversed and bonded phases are usually preferred. In addition, silica has a significant solubility in many solvents, particularly aqueous solvents and, thus, silica columns can be less stable than those packed with bonded phases. The analytical procedure can be a little more complex and costly with silica gel columns as, in general, a wider variety of more expensive solvents are required. Reversed and bonded phases utilize blended solvents such as hexane/ethanol, methanol/water or acetonitrile/water mixtures as the mobile phase and, consequently, are considerably more economical. Nevertheless, silica gel has certain areas of application for which it is particularly useful and is very effective for separating polarizable substances such as the polynuclear aromatic hydrocarbons and substances... 

The application of these methods to unsaturated hydrocarbons involves certain complications. Unsaturated hydrocarbons show an additional polarizability19 of 0.58 x 10 24 cm3 per double bond and 0.86 x 10 24 cm3 per triple bond in the molecule. Similarly the polarizability of a molecule containing a benzene ring exceeds that computed for the atoms present by about 1.28 x 10 24 cm3. These results are most readily explained on the basis that oscillations of charge from atom to atom are significant when double bonds are present. 

Unrestricted Hartree-Fock method, 231 IJnsaturated hydrocarbons, polarizability, 76... 

Dispersive forces are more difficult to describe. Although electric in nature, they result from charge fluctuations rather than permanent electrical charges on the molecule. Examples of purely dispersive interactions are the molecular forces that exist between saturated aliphatic hydrocarbon molecules. Saturated aliphatic hydrocarbons are not ionic, have no permanent dipoles and are not polarizable. Yet molecular forces between hydrocarbons are strong and consequently, n-heptane is not a gas, but a liquid that boils at 100°C. This is a result of the collective effect of all the dispersive interactions that hold the molecules together as a liquid. 

As a result of its highly polar character, silica gel is particularly useful in the separation of polarizable materials such as the aromatic hydrocarbons and polynuclear aromatics. It is also useful in the separation of weakly polar solute mixtures such as ethers, esters and in some cases, ketones. The mobile phases that are commonly employed with silica gel are the n-paraffins and mixtures of the n-paraffins with methylene dichloride or chloroform. It should be borne in mind that chloroform is opaque to UV light at 254 nm and thus, if a fixed wavelength UV detector is being used, methylene dichloride might be a better choice. Furthermore, chloroform is considered toxic and requires special methods of waste disposal. Silica gel is strongly deactivated with water and thus, to ensure stable retentive characteristics, the solvent used for the mobile phase should either be completely dry or have a controlled amount of water present. The level of water in the solvent that will have significant effect on solute retention is extremely small. The solubility of water in n-heptane is... 

In summary, examples of the successful use of silica gel as a conventional stationary phase are in the analysis of mixtures containing polarizable and relatively low polarity solutes typified by mixtures of aromatic hydrocarbons, polynuclear aromatics, nitro compounds, carotenes and vitamin A formulas. 

The silica gel surface is extremely polar and, as a result, must often be deactivated with a polar solvent such as ethyl acetate, propanol or even methanol. The bulk solvent is usually an n-alkane such as n-heptane and the moderators (the name given to the deactivating agents) are usually added at concentrations ranging from 0.5 to 5% v/v. Silica gel is very effective for separating polarizable materials such as the aromatic hydrocarbons, nitro hydrocarbons (aliphatic and aromatic), aliphatic ethers, aromatic esters, etc. When separating polarizable substances as opposed to substances with permanent dipoles, mixtures of an aliphatic hydrocarbon with a chlorinated hydrocarbon such as chlorobutane or methylene dichloride are often used as the mobile... 

The diastereoselectivity of the cycloaddition of cyclopentadiene with methyl acrylate in SC-CO2 at 40 °C and subcritical liquid CO2 at 22 °C is practically the same endojexo = 75 25 and 76 24 respectively) and is comparable to that found in hydrocarbon solvents (73 27 and 75 25 in heptane and cyclohexane, respectively). This shows that CO2, in these states, behaves like an apolar solvent with very low polarizability [82]. 

The solvent triangle classification method of Snyder Is the most cosDBon approach to solvent characterization used by chromatographers (510,517). The solvent polarity index, P, and solvent selectivity factors, X), which characterize the relative importemce of orientation and proton donor/acceptor interactions to the total polarity, were based on Rohrscbneider s compilation of experimental gas-liquid distribution constants for a number of test solutes in 75 common, volatile solvents. Snyder chose the solutes nitromethane, ethanol and dloxane as probes for a solvent s capacity for orientation, proton acceptor and proton donor capacity, respectively. The influence of solute molecular size, solute/solvent dispersion interactions, and solute/solvent induction interactions as a result of solvent polarizability were subtracted from the experimental distribution constants first multiplying the experimental distribution constant by the solvent molar volume and thm referencing this quantity to the value calculated for a hypothetical n-alkane with a molar volume identical to the test solute. Each value was then corrected empirically to give a value of zero for the polar distribution constant of the test solutes for saturated hydrocarbon solvents. These residual, values were supposed to arise from inductive and... 

Vinyl C—H bonds are more acidic than the C—H bonds in saturated hydrocarbons because of their higher s-character and the polarizability of the double bond, but the corresponding carbanions are essentially localized. Allylic C—H bonds have the s-character of saturated hydrocarbons, but the resulting carbanions now have the possibility of additional stabilization by delocalization. Allylic positions are thus generally the most acidic in alkenes. 

Gas-Liquid Chromatography. In gas-liquid chromatography (GLC) the stationary phase is a liquid. GLC capillary columns are coated internally with a liquid (WCOT columns) stationary phase. As discussed above, in GC the interaction of the sample molecules with the mobile phase is very weak. Therefore, the primary means of creating differential adsorption is through the choice of the particular liquid stationary phase to be used. The basic principle is that analytes selectively interact with stationary phases of similar chemical nature. For example, a mixture of nonpolar components of the same chemical type, such as hydrocarbons in most petroleum fractions, often separates well on a column with a nonpolar stationary phase, while samples with polar or polarizable compounds often resolve well on the more polar and/or polarizable stationary phases. Reference 7 is a metabolomics example of capillary GC-MS. 

---