Silica pigment

Primer Formulations. Coatings were formulated using standard techniques. Mill bases were prepared by dispersing the oligomer solution with pigments (silica, carbon black, titanium dioxide and barium sulfate in a 1 1 1 10 ratio). The viscosity of the formulation was reduced to spray viscosity by addition of solvent. 

Heat-stable bronze pigments (silica coated) 260°C... 

Aggregate, alumiiia (alumiiium oxide), cement raw mix, clay, dolomite, fluorspar, kaolin, light weight aggregate, lime, limestone, magnesia (magnesium oxide), pigments, silica (silicon dioxide), silica fume Products... 

Aluminum pigments, silica encapsulated, (PCR-type) PVC, powder coating, thermoplastic resins, thermosetting resins Improved chemical resistance and outdoor durability... 

A. These are often used as fillers, extenders, or pigments. Silica and alumina are widely used for catalyst supports. 

Silicosis—Caused by Amorphous Silica Technical Bulletin Pigments No. 76, Degussa Corp., Erankfurt, Germany, 1988. 

Pebble mills are frequently Uned with nonmetalUc materials when iron contamination would harm a product such as a white pigment or cement. Belgian silex (silica) or porcelain block are popular Unings. Sihea linings and baU media have proved to wear better than other nonmetalUc materials. The higher density of siUca media increases the produclion capacity and power draft of a given mill. 

In this article, we will discuss the use of physical adsorption to determine the total surface areas of finely divided powders or solids, e.g., clay, carbon black, silica, inorganic pigments, polymers, alumina, and so forth. The use of chemisorption is confined to the measurements of metal surface areas of finely divided metals, such as powders, evaporated metal films, and those found in supported metal catalysts. 

The composition of an epoxide moulding material will greatly depend on the specific application, and this has been discussed at length. ". The resin may be of the epoxide novolac type and there will also be present hardeners, fillers (such as silica), a silane coupling agent, pigment, flame retardant and a wax release agent. 

Fillers fibreglass, silicas, calcium carbonate, powdered metal pigments some may be absorbed potential primary irritant dust inhalation low toxicity... 

Cobalt ores are often found in association with copper(II) sulfide. Cobalt is a silver-gray metal and is used mainly for alloying with iron. Alnico steel, an alloy of iron, nickel, cobalt, and aluminum, is used to make permanent magnets such as those in loudspeakers. Cobalt steels are hard enough to be used as surgical steels, drill bits, and lathe tools. The color of cobalt glass is due to a blue pigment that forms when cobalt(II) oxide is heated with silica and alumina. 

Titanium dioxide (E171, Cl white 6) is a white, opaque mineral occurring naturally in three main forms rutile, anatase, and brookite. More than 4 million tons of titanium dioxide are produced per year and it is widely used for industrial applications (paints, inks, plastics, textiles) and in small amounts as a food colorant. ° "° Production and properties — Titanium oxide is mainly produced from ilmenite, a titaniferous ore (FeTiOj). Rutile and anatase are relatively pure titanium dioxide (Ti02) forms. Titanium oxide pigment is produced via chloride or sulfate processes via the treatment of the titanium oxide ore with chlorine gas or sulfuric acid, followed by a series of purification steps. High-purity anatase is preferred for utilization in the food industry. It may be coated with small amounts of alumina or silica to improve technological properties. 

TLC has been traditionally regarded as a simple, rapid, and inexpensive separation method, currently used mainly for preliminary examinations to give an indication of the number and variety of pigments present and help in the selection of suitable separation and purification procedures for further analysis. To avoid epoxy-furanoid rearrangements caused by inherent silica gel acidify, one pellet of a strong alkali such as KOH or NaOH should be added to the water used to make the thin layer, or in case of ready commercial plates, 0.1% triethylamine (TEA) should be added to the mobile phase. 

The most popnlar system is a reversed phase column (Cl8), on a silica base column. However, the use of C18 on a polymer-based column has been reported to provide better resolution, especially for the separation of complex anthocyanin mixtures containing acylated pigments. - Polymer-based columns also show better stability at low pH operating conditions. 

Silica gel plates also have been used for the separation of 16 different eye pigments of Drosophila melanogaster using two-dimensional development in nonpolar solvent systems [55]. Although not very common, two-dimensional development may be nsed in preparative scale on thick-layered plates for further analysis. 

White pigments such as calcium carbonate, aluminum hydroxide, silica, kaolin, or urea-formaldehyde resin are used as filler. The filler functions as an absorbent of melted components to prevent their adhesion on the thermal head. Thus, the filler is required to be high in oil absorption and not to wear the thermal head. 

Small-angle X-ray scattering (SAXS) data have made it possible to deduce the localisation of organic additives (pigments) in the bulk of isotactic polypropylene (iPP) [344]. This work has confirmed that the additives are located in the amorphous phase, in spite of their crucial influence on the formation of the crystalline phase of iPP. SAXS has also been used to study the 3D structure of different carbon-black aggregates, and silica-filled SBR rubber compounds [345]. 

Formerly derived from the natural mineral lapis lazuli, ultramarine blue pigments have, for more than a century, been manufactured synthetically. The materials used in the manufacture of ultramarines are china clay (a hydrated aluminosilicate), sodium carbonate, silica, sulfur and a carbonaceous reducing material such as coal tar pitch. For the manufacture of the blue pigments, the blend of ingredients is heated to a temperature of 750 800 °C over a period of 50-100 h, and the reaction... 

---