Chlorides physical properties

Physical properties. Colourless liquids when pure, benzoyl chloride, CjHjCOCl, is frequently pale yellow. Acetyl chloride, CH3COCI, has a pungent odour, fumes in moist air and is immediately hydrolysed by cold water. Benzoyl chloride also has a pungent odour, is lachry matory, and is hydrolysed only slowly by cold water, in which it is insoluble. 

The physical properties of a number of aliphatic acid chlorides are collected in Table 111,88. 

The physical properties of a few tjrpical acid chlorides of aromatic acids are collected in Table IV, 18 7). Some acid anhydrides are also included in this Table (compare Section 111,94). 

Ben2onitri1e [100-47-0] C H CN, is a colorless Hquid with a characteristic almondlike odor. Its physical properties are Hsted in Table 10. It is miscible with acetone, ben2ene, chloroform, ethyl acetate, ethylene chloride, and other common organic solvents but is immiscible with water at ambient temperatures and soluble to ca 1 wt% at 100°C. It distills at atmospheric pressure without decomposition, but slowly discolors in the presence of light. 

The common physical properties of acetyl chloride ate given in Table 1. The vapor pressure has been measured (2,7), but the experimental difficulties ate considerable. An equation has been worked out to represent the heat capacity (8), and the thermodynamic ideal gas properties have been conveniently organized (9). 

Chloroacetyl chloride [79-04-9] (CICH2COCI) is the corresponding acid chloride of chloroacetic acid (see Acetyl chloride). Physical properties include mol wt 112.94, C2H2CI2O, mp —21.8 C, bp 106°C, vapor pressure 3.3 kPa (25 mm Hg) at 25°C, 12 kPa (90 mm Hg) at 50°C, and density 1.4202 g/mL and refractive index 1.4530, both at 20°C. Chloroacetyl chloride has a sharp, pungent, irritating odor. It is miscible with acetone and bensene and is initially insoluble in water. A slow reaction at the water—chloroactyl chloride interface, however, produces chloroacetic acid. When sufficient acid is formed to solubilize the two phases, a violent reaction forming chloroacetic acid and HCl occurs. 

Vlayl fluoride [75-02-5] (VF) (fluoroethene) is a colorless gas at ambient conditions. It was first prepared by reaction of l,l-difluoro-2-bromoethane [359-07-9] with ziac (1). Most approaches to vinyl fluoride synthesis have employed reactions of acetylene [74-86-2] with hydrogen fluoride (HF) either directly (2—5) or utilizing catalysts (3,6—10). Other routes have iavolved ethylene [74-85-1] and HF (11), pyrolysis of 1,1-difluoroethane [624-72-6] (12,13) and fluorochloroethanes (14—18), reaction of 1,1-difluoroethane with acetylene (19,20), and halogen exchange of vinyl chloride [75-01-4] with HF (21—23). Physical properties of vinyl fluoride are given ia Table 1. 

Lead Chloride. Lead dichloride, PbCl2, forms white, orthorhombic needles some physical properties are given in Table 1. Lead chloride is slightly soluble in dilute hydrochloric acid and ammonia and insoluble in alcohol. It is prepared by the reaction of lead monoxide or basic lead carbonate with hydrochloric acid, or by treating a solution of lead acetate with hydrochloric acid and allowing the precipitate to settle. It easily forms basic chlorides, such as PbCl Pb(OH)2 [15887-88 ] which is known as Pattinson s lead white, an artist s pigment. 

Physical Properties. Nitrobenzene is readily soluble in most organic solvents and is completely miscible with diethyl ether and benzene. Nitrobenzene is only slightly soluble in water with a solubiUty of 0.19 parts pet 100 parts of water at 20°C and 0.8 pph at 80°C. Nitrobenzene is a good organic solvent. For example, it is used in Friedel-Crafts reactions because aluminum chloride is soluble in nitrobenzene. The physical properties of nitrobenzene are summarized in Table 1. 

Uses. Phthabc anhydride is used mainly in plasticizers, unsaturated polyesters, and alkyd resins (qv). PhthaUc plasticizers consume 54% of the phthahc anhydride in the United States (33). The plasticizers (qv) are used mainly with poly(vinyl chloride) to produce flexible sheet such as wallpaper and upholstery fabric from normally rigid polymers. The plasticizers are of two types diesters of the same monohydric alcohol such as dibutyl phthalate, or mixed esters of two monohydric alcohols. The largest-volume plasticizer is di(2-ethylhexyl) phthalate [117-81-7] which is known commercially as dioctyl phthalate (DOP) and is the base to which other plasticizers are compared. The important phthahc acid esters and thek physical properties are Hsted in Table 12. The demand for phthahc acid in plasticizers is naturally tied to the growth of the flexible poly(vinyl chloride) market which is large and has been growing steadily. 

Derivatives. In general, the esters of terephthaHc acid derived from saturated alcohols undergo the same reactions as dimethyl terephthalate. Some physical properties of six of these esters are Hsted in Table 23. The di- -butyl and di-2-ethyIhexyl esters find use as plasticizers (qv). Terephthaloyl chloride, which is prepared by reaction of terephthaHc acid and thionyl chloride, is used to prepare derivatives of terephthaHc acid. 

Derivatives. The dual functionaUty of trimellitic anhydride makes it possible to react either the anhydride group, the acid group, or both. Derivatives of trimellitic anhydride include ester, acid esters, acid chloride, amides, and amide—imides (136). Trimellitate esters are the most important derivatives, and physical properties of more significant esters are Hsted in Table 34. 

Approximately 98% of the potassium recovered ia primary ore and natural brine refining operations is recovered as potassium chloride. The remaining 2% consists of potassium recovered from a variety of sources. Potassium produced from these sources occurs as potassium sulfate combiaed with magnesium sulfate. Prom a practical point of view, the basic raw material for ak of the potassium compounds discussed ia this article, except potassium tartrate, is potassium chloride. Physical properties of selected potassium compounds are Hsted ia Table 3, solubkities ia Table 4. 

Table 1. Physical Properties of Anhydrous Aluminum Chloride ...

Physical Properties. Most quaternary compounds are soHd materials that have indefinite melting poiats and decompose on heating. Physical properties are determined by the chemical stmcture of the quaternary ammonium compound as well as any additives such as solvents. The simplest quaternary ammonium compound, tetramethylammonium chloride [75-57-0] is very soluble ia water (163) and iasoluble ia nonpolar solvents. As the molecular weight of the quaternary compound iacreases, solubiUty ia polar solvents decreases and solubiUty ia nonpolar solvents iacreases (164—166). For example, trimethyloctadecylammonium chloride [112-03-8] is soluble ia water up to whereas dimethyldioctadecylammonium chloride [107-64-2] has... 

PVC. Poly(vinyl chloride) (PVC), a very versatile polymer, is manufactured by the polymerisation of vinyl chloride monomer, a gaseous substance obtained from the reaction of ethylene with oxygen and hydrochloric acid. In its most basic form, the resin is a relatively hard material that requites the addition of other compounds, commonly plasticisers and stabilisers as well as certain other ingredients, to produce the desired physical properties for roofing use. The membranes come in both reinforced and nonreinforced constmctions, but since the 1980s the direction has been toward offering only reinforced membranes. The membrane thickness typically mns from 0.8—1.5 mm and widths typically in the range of 1.5—4.6 m. 

Sulfosahcyhc acid is prepared by heating 10 parts of sahcyhc acid with 50 parts of concentrated sulfuric acid, by chlorosulfonation of sahcyhc acid and subsequent hydrolysis of the acid chloride, or by sulfonation with hquid sulfur trioxide in tetrachloroethylene. It is used as an intermediate in the production of dyestuffs, grease additives, catalysts, and surfactants. It is also useful as a colorimetric reagent for ferric iron and as a reagent for albumin. Table 9 shows the physical properties of sahcyhc acid derivatives. 

Physical Properties. Thiophosgene [463-71-8] (thiocarbonyl chloride), CSCI2, is a malodorous, red-yeUow Hquid (bp 73.5°C, ( 20 1.5442). It is only slightly soluble with decomposition in water, but it is soluble in ether and various organic solvents. 

Physical Properties. Trichloromethanesulfenyl chloride [594-42-3] (perchloromethyl mercaptan, a misnomer but used as the common commercial name), CCl SCl, is a strongly acrid, pale yellow Hquid, boiling at 149°C with some decomposition at atmospheric pressure, 68°C at 6.93 kPa (52... 

Physical Properties. Thionyl chloride [7719-09-7], SOCI2, is a colorless fuming Hquid with a choking odor. Selected physical and thermodynamic properties are Hsted in Table 6. Thionyl chloride is miscible with many organic solvents including chlorinated hydrocarbons and aromatic hydrocarbons. It reacts quickly with water to form HCl and SO2. Thionyl chloride is stable at room temperature however, slight decomposition occurs just... 

Physical Properties. Sulfuryl chloride [7791-25-5] SO2CI2, is a colorless to light yellow Hquid with a pungent odor. Physical and thermodynamic properties are Hsted ia Table 7. Sulfuryl chloride dissolves sulfur dioxide, bromine, iodine, and ferric chloride. Various quaternary alkyl ammonium salts dissolve ia sulfuryl chloride to produce highly conductive solutions. Sulfuryl chloride is miscible with acetic acid and ether but not with hexane (193,194). 

Physical Properties. Methanesulfonyl chloride [124-63-0] (MSG), CH2SO2CI, is a clear Hquid, and is soluble in a wide variety of organic solvents, eg, methanol and acetone (Table 9). 

Stannous Chloride. Stannous chloride is available in two forms anhydrous stannous chloride, SnCl2, and stannous chloride dihydrate [10025-69-1], SnCl2 2H20, also called tin crystals or tin salts. These forms are sometimes used interchangeably however, where stabiUty, concentration, and adaptabihty are important, anhydrous stannous chloride is preferred. Even after long storage, changes in the stannous tin content of anhydrous stannous chloride are extremely low. Physical properties of the tin chlorides are Hsted in Table 1. 

---