Sodium chloride physical properties

The compound sodium hydride, formed in reaction (29), is a crystalline compound with physical properties similar to those of sodium chloride. The chemical properties are very different, however. Whereas sodium burns readily in chlorine, it reacts with hydrogen only on heating to about 300°C. While sodium chloride is a stable substance that dissolves in water to form Na+(aqJ and CV(aq), the alkali hydrides bum in air and some of them ignite spontaneously. In contact with water, a vigorous reaction occurs, releasing hydrogen ... 

Ethers are unaffected by sodium and by acetyl (or benzoyl) chloride. Both the purely aliphatic ethers e.g., di-n-butyl ether (C4H, )30 and the mixed aliphatic - aromatic ethers (e.g., anisole C3HSOCH3) are encountered in Solubility Group V the purely aromatic ethers e.g., diphenyl ether (C,Hj)20 are generally insoluble in concentrated sulphuric acid and are found in Solubility Group VI. The purely aliphatic ethers are very inert and their final identification may, of necessity, depend upon their physical properties (b.p., density and/or refractive index). Ethers do, however, suffer fission when heated with excess of 67 per cent, hydriodic acid, but the reaction is generally only of value for the characterisation of symmetrical ethers (R = R ) ... 

The nature of a surface will depend upon which atoms are exposed. For example, the surface of a crystal with the sodium chloride structure might consist of a mixture of atoms, as on 100 (Fig. 3.34a), or of just one atom type, as on 111 (Fig. 3.34b and 3.34c). However, it must be remembered that no surface is clean and uncontaminated unless it is prepared under very carefully controlled conditions. Absorbed gases, especially water vapor, are invariably present on a surface in air, which leads to changes in chemical and physical properties. 

Special cabinets are used for salt mist exposure in which a fine mist of a sodium chloride solution is produced at specified conditions. Change in mass or any physical property can be measured. This type of exposure has its origins in the determination of corrosion resistance rather than changes in bulk properties. 

Once the two salts are mixed in solution (acetone is a common solvent for this), the sodium chloride precipitates and is removed by filtration. The solvent is then removed under reduced pressure and, since salts have no vapour pressure, the ionic liquid remains in the flask. The problem with this reaction is that it is almost impossible to remove the last traces of chloride ions. The chloride not only influences the physical properties of the liquid such as melting point and viscosity, but is also a good nucleophile and can deactivate catalysts and affect reproducibility. A great deal of effort has been directed towards removal of the chloride contamination, including washes and chromatography, but none have proved to be completely effective [9], This has led to the development of some alternative synthetic routes. Simply exchanging Na[BF4]... 

Elemental composition Rh 49.17%, Cl 50.83%. Rhodium is analyzed in an aqueous solution (or after dissolving in water) by AA or other techniques. Insoluble chloride is extracted with aqua regia, diluted, and analyzed to determine the rhodium content using various instrumental techniques. The chloride may be decomposed at elevated temperatures and liberated chlorine identified by color and other physical properties. Chlorine may be measured quantitatively by dissolving in an acidified solution of potassium iodide and titrating liberated iodine with a standard solution of sodium thiosulfate, using starch indicator. 

Elemental composition Na 39.34%, Cl 60.66%. Aqueous solution may be analyzed for sodium by various instrumental methods (see Sodium) and for chloride ion by ion chromatography or chloride-ion selective electrode. Alternatively, the chloride ion may be measured by titration with a standard solution of silver nitrate using potassium chromate as indicator. Also, the salt can be identified by its physical properties. 

Since the electron distribution function for an ion extends indefi-finitely, it is evident that no single characteristic size can be assigned to it. Instead, the apparent ionic radius will depend upon the physical property under discussion and will differ for different properties. We are interested in ionic radii such that the sum of two radii (with certain corrections when necessary) is equal to the equilibrium distance between the corresponding ions in contact in a crystal. It will be shown later that the equilibrium interionic distance for two ions is determined not only by the nature of the electron distributions for the ions, as shown in Figure 13-1, but also by the structure of the crystal and the ratio of radii of cation and anion. We take as our standard crystals those with the sodium chloride arrangement, with the ratio of radii of cation and anion about 0.75 and with the amount of ionic character of the bonds about the same as in the alkali halogenides, and calculate crystal radii of ions such that the sum of two radii gives the equilibrium interionic distance in a standard crystal. 

I Sodium metal and chlorine gas react together to form sodium chloride. Although the compound sodium chloride is composed of sodium and chlorine, the physical and chemical properties of sodium chloride are very different from the physical and chemical properties of either sodium metal or chlorine gas. 

As discussed in Section 2.3, sodium chloride is not sodium, nor is it chlorine. Rather, it is a collection of sodium and chloride ions that forms a unique material having its own physical and chemical properties. 

From the foregoing you may anticipate that the chemistry of carbon compounds will be largely the chemistry of covalent compounds and will not at all resemble the chemistry of inorganic salts such as sodium chloride. You also may anticipate that the major differences in chemical and physical properties of organic compounds will arise from the nature of the other elements bonded to carbon. Thus methane is not expected to, nor does it have, the same chemistry as other one-carbon compounds such as methyllithium, CH3Li, or methyl fluoride, CH3F. 

The first explosives to be listed as permissible by the U. S. Bureau of Mines were certain Monobels and Carbonites, and Monobels are still among the most important of American per-missibles. Monobels contain about 10% nitroglycerin, about 10% carbonaceous material, wood pulp, flour, sawdust, etc., by the physical properties of which the characteristics of the explosive are somewhat modified, and about 80% ammonium nitrate of which, however, a portion, say 10%, may be substituted by a volatile salt such as sodium chloride. 

In Equation 4.21, the activity of pure water (a) is unity and the activity of the water with the inhibitor (a ) is the product of the water concentration (xw) and the activity coefficient (xw). The water concentration is known and the activity coefficient is easily obtained from colligative properties for the inhibitor, such as the freezing point depression. For instance the activity of water in aqueous sodium chloride solutions may be obtained from Robinson and Stokes (1959, p. 476) or from any of several handbooks of chemistry and physics. 

Solids such as sodium chloride (NaCl) and zinc chloride (ZnCl2) are made of ions that are held together by the attractive force of these oppositely charged particles. If ionic solids are dissolved in water, their ions are separated and can conduct an electric current. This physical property of ionic solids can be used to decide if a solid is held together by ionic bonds. 

---