Vinyl chloride physical properties

Poly(styrene-alt-MA)-g-poly(vinyl chloride), physical properties, 475 Poly(styrene-alt-monoallyl fumarate), 443 Poly(styrene-co-acrylonitrile)... 

Vlayl fluoride [75-02-5] (VF) (fluoroethene) is a colorless gas at ambient conditions. It was first prepared by reaction of l,l-difluoro-2-bromoethane [359-07-9] with ziac (1). Most approaches to vinyl fluoride synthesis have employed reactions of acetylene [74-86-2] with hydrogen fluoride (HF) either directly (2—5) or utilizing catalysts (3,6—10). Other routes have iavolved ethylene [74-85-1] and HF (11), pyrolysis of 1,1-difluoroethane [624-72-6] (12,13) and fluorochloroethanes (14—18), reaction of 1,1-difluoroethane with acetylene (19,20), and halogen exchange of vinyl chloride [75-01-4] with HF (21—23). Physical properties of vinyl fluoride are given ia Table 1. 

Uses. Phthabc anhydride is used mainly in plasticizers, unsaturated polyesters, and alkyd resins (qv). PhthaUc plasticizers consume 54% of the phthahc anhydride in the United States (33). The plasticizers (qv) are used mainly with poly(vinyl chloride) to produce flexible sheet such as wallpaper and upholstery fabric from normally rigid polymers. The plasticizers are of two types diesters of the same monohydric alcohol such as dibutyl phthalate, or mixed esters of two monohydric alcohols. The largest-volume plasticizer is di(2-ethylhexyl) phthalate [117-81-7] which is known commercially as dioctyl phthalate (DOP) and is the base to which other plasticizers are compared. The important phthahc acid esters and thek physical properties are Hsted in Table 12. The demand for phthahc acid in plasticizers is naturally tied to the growth of the flexible poly(vinyl chloride) market which is large and has been growing steadily. 

PVC. Poly(vinyl chloride) (PVC), a very versatile polymer, is manufactured by the polymerisation of vinyl chloride monomer, a gaseous substance obtained from the reaction of ethylene with oxygen and hydrochloric acid. In its most basic form, the resin is a relatively hard material that requites the addition of other compounds, commonly plasticisers and stabilisers as well as certain other ingredients, to produce the desired physical properties for roofing use. The membranes come in both reinforced and nonreinforced constmctions, but since the 1980s the direction has been toward offering only reinforced membranes. The membrane thickness typically mns from 0.8—1.5 mm and widths typically in the range of 1.5—4.6 m. 

The physical properties of vinyl chloride are Hsted in Table 1 (12). Vinyl chloride and water [7732-18-5] are nearly immiscible. The equiUbrium concentration of vinyl chloride at 1 atm partial pressure in water is 0.276 wt % at 25°C, whereas the solubiUty of water in vinyl chloride is 0.0983 wt % at 25°C and saturated pressure (13). Vinyl chloride is soluble in hydrocarbons, oil, alcohol, chlorinated solvents, and most common organic Hquids. 

Random copolymers of vinyl chloride and other monomers are important commercially. Most of these materials are produced by suspension or emulsion polymerization using free-radical initiators. Important producers for vinyl chloride—vinyUdene chloride copolymers include Borden, Inc. and Dow. These copolymers are used in specialized coatings appHcations because of their enhanced solubiUty and as extender resins in plastisols where rapid fusion is required (72). Another important class of materials are the vinyl chloride—vinyl acetate copolymers. Principal producers include Borden Chemicals Plastics, B. F. Goodrich Chemical, and Union Carbide. The copolymerization of vinyl chloride with vinyl acetate yields a material with improved processabihty compared with vinyl chloride homopolymer. However, the physical and chemical properties of the copolymers are different from those of the homopolymer PVC. Generally, as the vinyl acetate content increases, the resin solubiUty in ketone and ester solvents and its susceptibiUty to chemical attack increase, the resin viscosity and heat distortion temperature decrease, and the tensile strength and flexibiUty increase slightly. 

Acrylic Resins. The first synthetic polymer denture material, used throughout much of the 20th century, was based on the discovery of vulcanised mbber in 1839. Other polymers explored for denture and other dental uses have included ceUuloid, phenolformaldehyde resins, and vinyl chloride copolymers. Polystyrene, polycarbonates, polyurethanes, and acryHc resins have also been used for dental polymers. Because of the unique combination of properties, eg, aesthetics and ease of fabrication, acryHc resins based on methyl methacrylate and its polymer and/or copolymers have received the most attention since their introduction in 1937. However, deficiencies include excessive polymerization shrinkage and poor abrasion resistance. Polymers used in dental appHcation should have minimal dimensional changes during and subsequent to polymerization exceUent chemical, physical, and color stabiHty processabiHty and biocompatibiHty and the abiHty to blend with contiguous tissues. 

Other commercially relevant monomers have also been modeled in this study, including acrylates, styrene, and vinyl chloride.55 Symmetrical a,dienes substituted with the appropriate pendant functional group are polymerized via ADMET and utilized to model ethylene-styrene, ethylene-vinyl chloride, and ethylene-methyl acrylate copolymers. Since these models have perfect microstructure repeat units, they are a useful tool to study the effects of the functionality on the physical properties of these industrially important materials. The polymers produced have molecular weights in the range of 20,000-60,000, well within the range necessary to possess similar properties to commercial high-molecular-weight material. 

The materials used in nonwoven fabrics include a single polyolefin, or a combination of polyolefins, such as polyethylene (PE), polypropylene (PP), polyamide (PA), poly(tetrafluoroethylene) (PTFE), polyvinylidine fluoride (PVdF), and poly(vinyl chloride) (PVC). Nonwoven fabrics have not, however, been able to compete with microporous films in lithium-ion cells. This is most probably because of the inadequate pore structure and difficulty in making thin (<25 /rm) nonwoven fabrics with acceptable physical properties. 

The miscibility between poly (vinyl chloride) and poly-urethanes based on poly (oxytetramethylene) glycol can be improved by introducing opposite charge groups to form ionic bonds. The improvement in miscibility from ionic bonds between the two polymer systems provided the best chance for interpene-tration between the linear chains of VMCC and the PU networks in order to obtain good physical properties of the ionomer pseudo-IPN coatings from PU and VMCC. 

Reaction Rates and Physical Properties in the Radiation Graft-Copolymer System Poly(vinyl chloride)—Styrene... 

The physical properties of vinyl chlonde are listed in Table 1. Vinyl chloride and water are nearly immiscible. Vinyl chloride is soluble in hydrocarbons, oil. alcohol, chlorinated solvents, and most common organic liquids. 

---