Phthalate density

Potassium hydrogen phthalate is a primary standard used to measure the concentration of NaOH solutions. Find the true mass of potassium hydrogen phthalate (density = 1.636 g/mL) if the... 

Carrier Mixed dialkyl phthalates Density (Ib/gal) 8.20 EPA Number 1486-19... 

Stmcture is usually measured by a void volume test such as the absorption of dibutyl phthalate (DBPA) (15), or by bulk density measurements of the carbon black under compression. In order to eliminate the effects of pelletizing conditions the DBPA test has been modified to use a sample that has been precompressed at a pressure of 165 MPa (24,000 psi) and then broken up four successive times (24M4) (16). This procedure causes some aggregate breakdown and is claimed to more closely approximate the actual breakdown that occurs duting mbber mixing. 

J Li, MR Nelson, CY Peng, D Bashford, L Noodleman. Incorporating protein environments in density functional theory A self-consistent reaction field calculation of redox potentials of [2Ee2S] clusters in feiTedoxm and phthalate dioxygenase reductase. J Phys Chem A 102 6311-6324, 1998. 

Liquid densities of acetone, dibutyl phthalate = 764 and 1048 kg/m3 respectively. 

Pan, I.-C., Tang, M., and Chen, Y.-P. Densities and viscosities of binary liquid mixtures of vinyl acetate, diethyl oxalate, and dibutyl phthalate with normal alkanols at 303.15 K, J. Chem. Eng. Data, 45(6) 1012-1015, 2000. 

The influence of adding polyfunctional monomers having different structures and functionality into a dicumyl peroxide-based crosslinking system for LDPE was investigated. Monomers employed were diallyl phthalate, trimethylolpropane trimethacrylate and triallyl cyanurate. The effects of formulation on matrix gel content and on foam density at similar gel content were examined and the dependence of foam density on melt modulus assessed. The applicability of swell ratio for estimating foam density was evaluated and the suitability of triallyl cyanurate as a crosslinking promoter for LDPE foam demonstrated. 20 refs. 

Although some polymers may be satisfactory when used under the stress of static loads, they may fail when subjected to impact. The impact resistance, or resistance to brittle fracture, is a function of the molecular weight of a polymer. Thus uhmwpe is much more resistant to impact failure than general purpose high-density polyethylene (hdpe). The impact resistance of brittle polymers is also increased by the addition of plasticizers. Thus polyvinyl chloride (PVC), plasticized by relatively large amounts of dioctyl phthalate, is much less brittle than unplasticized rigid PVC. 

Thirty mice of an inbred colony were used to study the effect of di(2-ethylhexyl) phthalate on reproductive function (Jain Joshi, 1991). Fifteen mice were dosed orally with 1000 mg/kg bw di(2-ethylhexyl) phthalate [purity not specified] in 0.1 mL olive oil for one week. The fertility (evaluated by the ability of the motile spermatozoa to fertilize normal cycling females) was reduced from 90 to 75%. Sperm density and sperm motility were also significantly reduced. 

ABA ABS ABS-PC ABS-PVC ACM ACS AES AMMA AN APET APP ASA BR BS CA CAB CAP CN CP CPE CPET CPP CPVC CR CTA DAM DAP DMT ECTFE EEA EMA EMAA EMAC EMPP EnBA EP EPM ESI EVA(C) EVOH FEP HDI HDPE HIPS HMDI IPI LDPE LLDPE MBS Acrylonitrile-butadiene-acrylate Acrylonitrile-butadiene-styrene copolymer Acrylonitrile-butadiene-styrene-polycarbonate alloy Acrylonitrile-butadiene-styrene-poly(vinyl chloride) alloy Acrylic acid ester rubber Acrylonitrile-chlorinated pe-styrene Acrylonitrile-ethylene-propylene-styrene Acrylonitrile-methyl methacrylate Acrylonitrile Amorphous polyethylene terephthalate Atactic polypropylene Acrylic-styrene-acrylonitrile Butadiene rubber Butadiene styrene rubber Cellulose acetate Cellulose acetate-butyrate Cellulose acetate-propionate Cellulose nitrate Cellulose propionate Chlorinated polyethylene Crystalline polyethylene terephthalate Cast polypropylene Chlorinated polyvinyl chloride Chloroprene rubber Cellulose triacetate Diallyl maleate Diallyl phthalate Terephthalic acid, dimethyl ester Ethylene-chlorotrifluoroethylene copolymer Ethylene-ethyl acrylate Ethylene-methyl acrylate Ethylene methacrylic acid Ethylene-methyl acrylate copolymer Elastomer modified polypropylene Ethylene normal butyl acrylate Epoxy resin, also ethylene-propylene Ethylene-propylene rubber Ethylene-styrene copolymers Polyethylene-vinyl acetate Polyethylene-vinyl alcohol copolymers Fluorinated ethylene-propylene copolymers Hexamethylene diisocyanate High-density polyethylene High-impact polystyrene Diisocyanato dicyclohexylmethane Isophorone diisocyanate Low-density polyethylene Linear low-density polyethylene Methacrylate-butadiene-styrene... 

HPLC column which is closed with conventional frits on both sides. The extraction cell is kept at a temperature of 315 K, with a CO2 flow rate of l.Oml/min, while for the extraction a linear pressure gradient from 79 to 317 bar over 50 min is employed. The weight reduction after the extraction is 119 mg, corresponding to 18.5%. At the final extraction density of 0.9g/ml (315 bar), the valve at the SFC probe is closed in order to switch to stop-flow conditions. The proton spectrum shown in Figure 7.2.21 is acquired under static conditions. From this, the structure of the extracted phthalate could be assigned as bis(2-ethylhexyl) phthalate. 

Using simple laboratory equipment, it is possible to detect variations of the density of the order of 1 kg m-3 therefore, density measurements would be useless for diglycidyl ether of bisphenol A and diamino diphenyl methane (DGEBA-DDM), because both components have close Ma values. They would be moderately sensitive for unsaturated polyesters of maleate/ phthalate (1/1) of propylene glycol crosslinked by styrene (36 wt%), and relatively sensitive for DGEBA cured by diamino diphenyl sulphone (DDS) or phthalic anhydride (PA), for which relative variations of the molar ratio y of about 5% could be detected. In certain cases, where some comonomer (PA or styrene) can be lost by evaporation during the cure, density measurements can constitute a simple and efficient method of control way (e.g., for non-filled materials). 

Calculate the time taken for the liquid level to fall to 5 cm below the top of the tube, neglecting the effects of bulk flow in the vapour. 1 kmol occupies 22.4 m3. Molecular weights of acetone, dibutyl phthalate = 58 and 279 kg/kmol respectively. Liquid densities of acetone, dibutyl phthalate = 764 and 1048 kg/m3 respectively. Vapour pressure of acetone at 315 K = 60.5 kN/m2. Diffusivity of acetone vapour in air at 315 K = 0.123 cm2/s. 

---