Phosphines solubility

Phosphine soluble in aqueous catalyst in catalyst phase unsuitable... 

In the early 1970 s, Bayer et al. reported the first use of soluble polymers as supports for the homogeneous catalysts. [52] They used non-crosslinked linear polystyrene (Mw ca. 100 000), which was chloromethylated and converted by treatment with potassium diphenylphosphide into soluble polydiphenyl(styrylmethyl)phosphines. Soluble macromolecular metal complexes were prepared by addition of various metal precursors e.g. [Rh(PPh3)Cl] and [RhH(CO)(PPh3)3]. The first complex was used in the hydrogenation reaction of 1-pentene at 22°C and 1 atm. H2. After 24 h (50% conversion in 3 h) the reaction solution was filtered through a polyamide membrane [53] and the catalysts could be retained quantitatively in the membrane filtration cell. [54] The catalyst was recycled 5 times. Using the second complex, a hydroformylation reaction of 1-pentene was carried out. After 72 h the reaction mixture was filtered through a polyamide membrane and recycled twice. 

Table I. Synthesis of Alkyl Chlorides form Carbon Tetrachloride, a Phosphinated Soluble Polymer and an Alcohol or Thiol...

Phosphine is a colourless gas at room temperature, boiling point 183K. with an unpleasant odour it is extremely poisonous. Like ammonia, phosphine has an essentially tetrahedral structure with one position occupied by a lone pair of electrons. Phosphorus, however, is a larger atom than nitrogen and the lone pair of electrons on the phosphorus are much less concentrated in space. Thus phosphine has a very much smaller dipole moment than ammonia. Hence phosphine is not associated (like ammonia) in the liquid state (see data in Table 9.2) and it is only sparingly soluble in water. 

Although Pd is cheaper than Rh and Pt, it is still expensive. In Pd(0)- or Pd(ll)-catalyzed reactions, particularly in commercial processes, repeated use of Pd catalysts is required. When the products are low-boiling, they can be separated from the catalyst by distillation. The Wacker process for the production of acetaldehyde is an example. For less volatile products, there are several approaches to the economical uses of Pd catalysts. As one method, an alkyldi-phenylphosphine 9, in which the alkyl group is a polyethylene chain, is prepared as shown. The Pd complex of this phosphine has low solubility in some organic solvents such as toluene at room temperature, and is soluble at higher temperature[28]. Pd(0)-catalyzed reactions such as an allylation reaction of nucleophiles using this complex as a catalyst proceed smoothly at higher temperatures. After the reaction, the Pd complex precipitates and is recovered when the reaction mixture is cooled. 

Pd can also be recovered as insoluble complexes such as the dimethylglyox-ime complex, or PdCUiPhiP) by treatment with HCl and PI13P. When water-soluble phosphines are used, the catalyst always remains in the aqueous phase and can be separated from a product in the organic phase, and is used repeatedly. 

Polyphenylene polymers can be prepared by this coupling. For example, the preparation of poly(/i-quaterphenylene-2,2 -dicarboxylic acid) (643) was carried out using aqueous NaHCO and a water-soluble phosphine ligand (DPMSPP)[5I I]. Branched polyphenylene was also prepared[5l2). 

These are water-soluble crystalline compounds sold as concentrated aqueous solutions. The methylol groups are highly reactive (118—122) and capable of being cured on the fabric by reaction with ammonia or amino compounds to form durable cross-linked finishes, probably having phosphine oxide stmctures after post-oxidizing. This finishing process, as developed by Albright Wilson, is known as the Proban process. 

Aqueous mineral acids react with BF to yield the hydrates of BF or the hydroxyfluoroboric acids, fluoroboric acid, or boric acid. Solution in aqueous alkali gives the soluble salts of the hydroxyfluoroboric acids, fluoroboric acids, or boric acid. Boron trifluoride, slightly soluble in many organic solvents including saturated hydrocarbons (qv), halogenated hydrocarbons, and aromatic compounds, easily polymerizes unsaturated compounds such as butylenes (qv), styrene (qv), or vinyl esters, as well as easily cleaved cycHc molecules such as tetrahydrofuran (see Furan derivatives). Other molecules containing electron-donating atoms such as O, S, N, P, etc, eg, alcohols, acids, amines, phosphines, and ethers, may dissolve BF to produce soluble adducts. 

Rhodium complexes with oxygen ligands, not nearly as numerous as those with amine and phosphine complexes, do, however, exist. A variety of compounds are known, iucluding [Rh(ox)3] [18307-26-1], [Rh(acac)3] [14284-92-5], the hexaaqua ion [Rh(OH2)3] [16920-31 -3], and Schiff base complexes. Soluble rhodium sulfate, Rh2(804 )3-a H2 0, exists iu a yellow form [15274-75-6], which probably coutaius [Rh(H20)3], and a red form [15274-78-9], which contains coordinated sulfate (125). The stmcture of the soluble nitrate [Rh(N03)3 2H20 [10139-58-9] is also complex (126). Another... 

A new homogeneous process for hydroformylation of olefins using a water-soluble catalyst has been developed (40). The catalyst is based on a rhodium complex and utilizes a water-soluble phosphine such as tri(M-sulfophenyl)phosphine. The use of an aqueous phase simplifies the separation of the catalyst and products (see Oxo process). 

This is an ion-exchanger like the sulfonated polymer. The siUca surface can also be functionalized with phosphine complexes when combined with rhodium, these give anchored complexes that behave like their soluble and polymer-supported analogues as catalysts for olefin hydrogenation and other reactions ... 

CP can also be prepared by the reaction of cellulose with phosphoms oxychloride in pyridine (37) or ether in the presence of sodium hydroxide (38). For the most part these methods yield insoluble, cross-linked, CP with a low DS. A newer method based on reaction of cellulose with molten urea—H PO is claimed to give water soluble CP (39). The action of H PO and P2 5 cellulose in an alcohol diluent gives a stable, water-soluble CP with a high DS (>5% P) (40). These esters are dame resistant and have viscosities up to 6000 mPa-s(=cP) in 5 wt % solution. Cellulose dissolved in mixtures of DMF—N2O4 can be treated with PCl to give cellulose phosphite [37264-91-8] (41) containing 11.5% P and only 0.8% Cl. Cellulose phosphinate [67357-37-5] and cellulose phosphonate [37264-91 -8] h.a.ve been prepared (42). 

Aeetylene is a simple asphyxiant and anaestlietie. Pure aeetylene is a eolourless, highly flammable gas with an ethereal odour. Material of eommereial purity has an odour of garlie due to the presenee of impurities sueh as phosphine. Its physieal properties are shown in Table 9.4. Aeetylene, whieh eondenses to a white solid subliming at -83°C, is soluble in its own volume of water but highly soluble in aeetone. 

Phosphine is rather insoluble in water at atmospherie pressure but is more soluble in... 

A water-soluble phosphine derivative of diazepam allows for more convenient parenteral tranquilizer therapy and avoids some complications due to blood pressure lowering caused by the propylene glycol medium otherwise required for administration. Fosazepam (82) is prepared from benzodiazepine by sodium hydride-mediated alkylation with chioromethyldimethyl phosphine... 

Cationic phosphine ligands containing guanidiniumphenyl moieties were originally developed in order to make use of their pronounced solubility in water [72, 73]. They were shown to form active catalytic systems in Pd-mediated C-C coupling reactions between aryl iodides and alkynes (Castro-Stephens-Sonogashira reaction) [72, 74] and Rh-catalyzed hydroformylation of olefins in aqueous two-phase systems [75]. 

Olivier-Bourbigou s group, for example, has recently shown that phosphite ligands can be used in Rh-catalyzed hydroformylation in ionic liquids as well as the well loiown phosphine systems [81]. Since phosphite ligands are usually unstable in aqueous media, this adds (apart from the much better solubility of higher olefins in... 

When water-miscible ionic liquids are used as solvents, and when the products are partly or totally soluble in these ionic liquids, the addition of polar solvents, such as water, in a separation step after the reaction can make the ionic liquid more hydrophilic and facilitate the separation of the products from the ionic liquid/water mixture (Table 5.3-2, case e). This concept has been developed by Union Carbide for the hydroformylation of higher alkenes catalyzed by Rh-sulfonated phosphine ligand in the N-methylpyrrolidone (NMP)/water system. Thanks to the presence of NMP, the reaction is performed in one homogeneous phase. After the reaction. 

Cone angle concepts, 2,1012-1028 chelate effects, 2,1012 definitions, 2,1015 models, 2,1015 phosphines chiral, 2,1014 polydentate, 2,1013 solubility effects, 2,1014 use, 2,1028... 

The distilled product can be used as a catalyst, although it usually has a relatively strong phenylphosphine odor. It is quite deliquescent, and it has not been satisfactorily recrystallized. If rigorous purification and deodorization are desired, the product is dissolved in water, a small amount of hydrogen peroxide is added to oxidize the phosphines, the solution is reneutralized, saturated with salt, and extracted with chloroform, and the product is refractionated. One cycle is normally enough. Pure product is essentially odorless, very hygroscopic, and soluble in polar solvents. 

Extractants derived from the carbamoylmethylphosphoryl moiety (CMP) were studied in the phosphonate, phosphinate, and phosphine oxide classes. Our studies focused on dihexyl-N,N-diethylcarba-moylmethylphosphonate, DHDECMP, hexyl hexyl-N,N-diethylcarbamoyl-methylphosphinate, HHDECMP, and octyl(phenyl)-N,N-diisobutylcarba-moylmethylphosphine oxide, 0D[ IB]CMP0. The three types of CMP extractants were compared on the basis of nitric acid and extractant dependencies for Am(III), solubility of complexes on loading with Nd(III) and U(VI), and selectivity over fission products. On the basis of the above data two conceptual flowsheets were developed. The first flowsheet involves the extraction of all of the actinides from HLLW using 0.4 M 0D[IB]CMP0 in DEB. The second flowsheet involves the extraction of all of the actinides from dissolved spent LWR fuel using 0.8 M DHDECMP in DEB. 

Coordination-catalyzed ethylene oligomerization into n-a-olefins. The synthesis of homologous, even-numbered, linear a-olefins can also be performed by oligomerization of ethylene with the aid of homogeneous transition metal complex catalysts [26]. Such a soluble complex catalyst is formed by reaction of, say, a zero-valent nickel compound with a tertiary phosphine ligand. A typical Ni catalyst for the ethylene oligomerization is manufactured from cyclo-octadienyl nickel(O) and diphenylphosphinoacetic ester ... 

---