Phase scope

The scope of this section restricts the discussion. One omitted topic is the collision and interaction of molecules with surfaces (see [20, 21] and section A3.9). This topic coimects quantum molecular dynamics in gas and condensed phases. Depending on the time scales of the interaction of a molecule witli a surface, the... 

It is beyond the scope of these introductory notes to treat individual problems in fine detail, but it is interesting to close the discussion by considering certain, geometric phase related, symmetry effects associated with systems of identical particles. The following account summarizes results from Mead and Truhlar [10] for three such particles. We know, for example, that the fermion statistics for H atoms require that the vibrational-rotational states on the ground electronic energy surface of NH3 must be antisymmetric with respect to binary exchange... 

Several hundred types of Hquid phases are commercially available. These have been used individually or in combination with other Hquid phases, inorganic salts, acids, or bases. The selection of stationary phases for a particular appHcation is beyond the scope of this article, however, it is one of the most important chromatographic tasks. Stationary phase selection is discussed at length in books, journal articles, and catalogs from vendors. See General References for examples. 

The plate dryer is limited in its scope of apphcations only in the consistency of the feed material (the products must be friable, free flowing, and not undergo phase changes) and diying temperatures up to 320°C. Applications include speci ty chemicals, pharmaceuticals, foods, polymers, pigments, etc. Initial moisture or volatile level can be as high as 65 percent and the unit is often used as a final dryer to take materials to a bone-dry state, if necessary. The plate dryer can also be used for heat treatment, removal of waters of hydration (bound moisture), solvent removal, and as a product cooler. 

The rates of these reactions bodr in the gas phase and on the condensed phase are usually increased as the temperature of die process is increased, but a substantially greater effect on the rate cati often be achieved when the reactants are adsorbed on die surface of a solid, or if intense beams of radiation of suitable wavelength and particles, such as electrons and gaseous ions with sufficient kinetic energies, can be used to bring about molecular decomposition. It follows drat the development of lasers and plasmas has considerably increased die scope and utility of drese thermochemical processes. These topics will be considered in the later chapters. 

Kinetic investigations cover a wide range from various viewpoints. Chemical reactions occur in various phases such as the gas phase, in solution using various solvents, at gas-solid, and other interfaces in the liquid and solid states. Many techniques have been employed for studying the rates of these reaction types, and even for following fast reactions. Generally, chemical kinetics relates to tlie studies of the rates at which chemical processes occur, the factors on which these rates depend, and the molecular acts involved in reaction mechanisms. Table 1 shows the wide scope of chemical kinetics, and its relevance to many branches of sciences. 

Life cycle assessment is defined by ISO 14040 as compilation and evalu ation of inputs, outputs and the potential environmental impacts of a product system throughout its life cycle. The ISO standards regulate the procedural aspects of LCA. They do not, however, provide all the information required for carrying out an LCA study. The main phases of LCA are goal and scope definition, inventory, impact assessment, and interpretation. The various applications of LCA are not regulated by the standard (Fig. 15.1). 

The pilot study is likely to use all the same Quality Management tools that were used for the integration framework development (Chapter 5). However, the limited scope of the pilot study enforces some limitations and compromises—it will not be possible to make changes outside of the department covered by the pilot. Any existing interfaces with other departments must remain the same. This will impact the design phases of the work. For example, Material Safety Data Sheets (MSDS) may currently be prepared locally, in the overall project it might be proposed to develop these centrally. However, for the pilot study it will not be possible develop the central resource so the pilot would have to continue to rely on local resources and there will be no efficiency improvement. 

A detailed description of methods for studying dynamic (i.e. time-dependent) phenomena and condensed phases is outside the scope of this book. The common feature for all these methods, however, is the need for an energy surface upon which the dynamics can take place. The generation of such a surface normally relies at least partly on results from calculations of the types discussed in Chapters 2-6, and it may therefore be of interest to briefly discuss the fundamentals. 

Scheduling of work in process engineering or design is a near impossibility as far as pin-point accuracy is concerned. The very developmental and planning nature of the early phases, as well as the continuous follow-through and follow-up, make this difficult. It is seldom that one can foresee specific changes, delays, etc. Very few projects are clear-cut and well defined ( frozen ) as to scope or design conditions except for small Jobs and repeat or duplicate projects. 

Each of these sine functions represents a discrete component of the vibration signature discussed previously. The amplitudes of each discrete component and their phase angles can be determined by integral calculus when the function /(f) is known. Because the subject of integral calculus is beyond the scope of this chapter, the math required to determine these integrals are not presented. A vibration analyzer and its associated software perform this determination using FFT. 

The first phase is a clear definition of the scope of work that is to be performed during the shutdown or maintenance outage. This definition must be more than a macro-level listing of the major tasks that are to be performed. Instead, each of these major or macro-level tasks must be fully defined. The purpose of this procedure is to provide an effective method of planning, material control, and follow-up of repetitive, non-repetitive, and capital shutdown work. 

The implementation phase is comprised of the actual outage duration. During this period, all of the tasks included in the scope of work are scheduled for completion. 

---