Performance General

Figure 20 shows values of the channel enthalpy extraction ratio for a number of channels. Enthalpy extraction (111) equal to that required by a proposed demonstration plant (112) has been achieved. Channels have performed generally in accordance with predictions. 

Low levels of particulates or potential poisons can sometimes be tolerated without a dramatic decrease in performance. Generally it has been recommended that the maximum particulate concentration not exceed 115 mg/m and that the maximum poison concentration not exceed 25 ppm (14). 

The condition of the test metal is important. Clean metal samples with uniform finishes are preferred. The accelerating effects of surface defects lead to deceptive results in samples. The ratio of the area of a defect to the total surface area of the metal is much higlier in a sample than in any metal in service. This is an indication of the inaccuracy of tests made on metals with improper finishes. The sample metal should have the same type of heat treatment as the metal to be used in service. Different heat treatments have different effects on corrosion. Heat treatment may improve or reduce the corrosion resistance of a metal in an unpredictable manner. For the purpose of selectivity, a metal stress corrosion test may be performed. General trends of the performance of a material can be obtained from such tests however, it is difficult to reproduce the stress that actually will occur during service. 

Reciprocating Up to 100 Little Performance generally maintained. Some reduction in speed may be advisable to reduce power input required... 

Catalytic hydrogenations were performed generally under 2-8 bar of H2 at 25 to 40°C in methanol or methanol/water (HCl) media, with a total volume of 80-... 

Catalytic hydrogenations were performed generally under 500 psig of H2 at 25 or 80 °C in H20 or 1 1 H20/EtOH media, typically with a total volume of 5 mL the substrates were essentially insoluble in water, but dissolved readily in the mixed medium. H20/NaOH and H20/buffer imply, respectively, use of a 1 1 mixture of the Ru catalyst solution with either 5.0 mM aq. NaOH or a pH 10 buffer solution (made from 44 mM NaHC03 and 17.6 mM NaOH (19)). Catalyst concentrations were either 4.1 or 2.05 mM, while the substrate (S) concentration was always 100 mM. The reaction mixture was placed into a glass sleeve equipped with a magnetic stir bar in air. The sleeve was placed in a steel... 

Kinzell, J.H., N.K. Ames, S.D. Sleight, J.D. Rrehbiel, C. Kuo, MJ. Zabik, and L.R. Shull. 1981. Subchronic administration of technical pentachlorophenol to lactating dairy cattle performance, general health, and pathologic changes. Jour. Dairy Sci. 64 42-51. 

This type of hydrodehalogenation has been performed generally in the presence of organic or inorganic bases to neutralize the hydrogen halides formed. Among published results, the use of rhodium complexes as catalysts dominates, but palladium and ruthenium complexes have also been applied on a frequent basis. 

Catalytic activity and electrochemical performance generally increase as the NiO and YSZ particle sizes are reduced. However, ultrafine powders are prone to agglomeration during the milling and mixing process the distributions of the phases (and hence the percolation threshold and many other important properties) are determined by the agglomeration size, not by the primary particle size. 

Flexibility comes from decoupling making components independent of one another. Optimization for performance generally means that pieces of code that were ideally decoupled become dependent on one another s details. So the more you optimize, the... 

The ability to provide accurate and reliable data is central to the role of analytical chemists, not only in areas like the development and manufacture of drugs, food control or drinking water analysis, but also in the field of environmental chemistry, where there is an increasing need for certified laboratories (ISO 9000 standards). The quality of analytical data is a key factor in successfully identifying and monitoring contamination of environmental compartments. In this context, a large collection of methods applied to the routine analysis of prime environmental pollutants has been developed and validated, and adapted in nationally or internationally harmonised protocols (DIN, EPA). Information on method performance generally provides data on specificity, accuracy, precision (repeatability and reproducibility), limit of detection, sensitivity, applicability and practicability, as appropriate. 

Perform general GMP compliance inspection. Review the potential for contamination and mix-ups thoroughly. 

Hiah-Performance General Purpose Cleaner Concentrate... 

It is clear that these tests take a significant amount of time to perform. Generally, 15 min to 1 hr should be allowed for each test, once the appropriate stresses or strains have been found. 

There is both a generalized and a more discrete type of social phobia. In the generalized type, the patient fears practically all social situations in which evaluation and scrutiny are possible. It is significantly more common than the discrete type, in which the individual fears a very specific social situation, usually of public speaking or public performance. Generalized social phobia is also more severe and disabling than discrete social phobia. 

The majority of studies into the catalytic behaviour of dendrimers with chiral catalytic centres at the periphery of the dendritic support have concerned non-phosphine-based catalysts. As has become apparent in these studies, the effect of the dendrimer fixation on the catalytic performance generally depends on the individual system. Factors such as the high local density of catalytic sites, the interaction of functional groups in the dendrimer backbone with the catalysts and the structural rigidity or flexibility of the dendrimers seem to play a role in many cases. 

Another parameter that can have a great influence on the results obtained is the type of the simulation performed. Generally, simulations are carried out at constant particle number (N). The volume (V) and energy (E) of the simulated system can be held constant, leading to a so-called NVE, or microcanonical, ensemble. When the volume and temperature are held constant, this yields a canonical or NVT ensemble. In both cases, the size of the simulated system is chosen in such a way as to represent the desired state of the phospholipid, mostly the liquid crystalline La phase. The surface per lipid and the thickness of the bilayer are set based on experimental values and remain unchanged during the simulation. Therefore, the system is not able to adjust its size and thickness. 

Barrier Plastics. When plastics replace metals and glass in packaging, their permeability is often a limiting property. Barrier performance generally increases with density and crystallinity. The most promising barrier plastics include ethylene/vinyl alcohol, polyvinylidene chloride, polyacrylonitrile, and polyethylene naphthoate. These are used most efficiently by laminating them to commodity plastics such as polyethylene and polyethylene terephthalate. 

Modular FORTRAN programs for performing general ab initio multireference single- and double-excitation configuration interaction, averaged coupled-pair functional and linearized couple-cluster method calculations. Cray and other versions. 

---