Paraffins reforming

We have explored rare earth oxide-modified amorphous silica-aluminas as "permanent" intermediate strength acids used as supports for bifunctional catalysts. The addition of well dispersed weakly basic rare earth oxides "titrates" the stronger acid sites of amorphous silica-alumina and lowers the acid strength to the level shown by halided aluminas. Physical and chemical probes, as well as model olefin and paraffin isomerization reactions show that acid strength can be adjusted close to that of chlorided and fluorided aluminas. Metal activity is inhibited relative to halided alumina catalysts, which limits the direct metal-catalyzed dehydrocyclization reactions during paraffin reforming but does not interfere with hydroisomerization reactions. 

During n-paraffin reforming over Pt-based catalysts, supported on chlorided alumina, methane is produced on the metal function (3). Only a very small amount of methane is produced by a carbocation mechanism on acid sites of the... 

These results, together with those in [3, 6, 7], indicate that coke in paraffin reforming derives mainly from the C5N intermediates. We next use readily available MCP as the model compound for C5N to study coking kinetics. 

From n-heptane up, the transformation of n-paraffins into cyclopentanes is negligible and the production of aromatics increases with the length of the chain on all the catalysts. Among the possible products of heavy paraffin reforming, alkyl benzenes and bicyclic aromatics are the greatest coke producers. Thus, the selectivity to these products influences the coking capacity of the... 

For the refiner, the reduction in benzene concentration to 3% is not a major problem it is achieved by adjusting the initial point of the feed to the catalytic reformers and thereby limiting the amount of benzene precursors such as cyclohexane and Cg paraffins. Further than 3% benzene, the constraints become very severe and can even imply using specific processes alkylation of benzene to substituted aromatics, separation, etc. 

A key process in the production of gasoline, catalytic reforming is used to increase the octane number of light crude fractions having high paraffin and naphthene contents (C7-C8-C9) by converting them to aromatics. 

As a complementary process to reforming, isomerization converts normal paraffins to iso-paraffins, either to prepare streams for other conversions nCi —> /C4 destined for alkylation or to increase the motor and research octane numbers of iight components in the gasoiine pooi, i.e., the C5 or Cs-Ce fractions from primary distillation of the crude, or light gasoline from conversion processes, having low octane numbers. 

We cite isomerization of Cs-Ce paraffinic cuts, aliphatic alkylation making isoparaffinic gasoline from C3-C5 olefins and isobutane, and etherification of C4-C5 olefins with the C1-C2 alcohols. This type of refinery can need more hydrogen than is available from naphtha reforming. Flexibility is greatly improved over the simple conventional refinery. Nonetheless some products are not eliminated, for example, the heavy fuel of marginal quality, and the conversion product qualities may not be adequate, even after severe treatment, to meet certain specifications such as the gasoline octane number, diesel cetane number, and allowable levels of certain components. 

The reformer outlet composition is deterrnined by an approach to the simultaneous equiUbria of reactions 3 and 4, where m = 2n + 2 represents the paraffinic nature of natural gas. The stoichiometry of the reformed gas can be conveniently characterized by the ratio R, where... 

Reactions 8 and 9 are important steps for the Hquid-phase nitration of paraffins. The nitric oxide which is produced is oxidized with nitric acid to reform nitrogen dioxide, which continues the reaction. The process is compHcated by the presence of two Hquid phases consequentiy, the nitrogen oxides must transfer from one phase to another. A large interfacial area is needed between the two phases. 

Of the main reactions, aromatization takes place most readily and proceeds ca 7 times as fast as the dehydroisomerization reaction and ca 20 times as fast as the dehydrocyclization. Hence, feeds richest in cycloparaftins are most easily reformed. Hydrocracking to yield paraffins having a lower boiling point than feedstock proceeds at about the same rate as dehydrocyclization. 

In order to obtain pure aromatics, cmde reformate is extracted to separate the aromatics from unreacted paraffins and cyclop araftins. The aromatics are, in turn, separated by simple fractional distillation to yield high purity benzene, toluene, xylenes, and aromatics. 

Toluene, Benzene, and BTX Reeoveiy. The composition of aromatics centers on the C - and Cg-fraction, depending somewhat on the boihng range of the feedstock used. Most catalytic reformate is used directiy in gasoline. That part which is converted to benzene, toluene, and xylenes for commercial sale is separated from the unreacted paraffins and cycloparaffins or naphthenes by hquid—hquid extraction or by extractive distillation. It is impossible to separate commercial purity aromatic products from reformates by distillation only because of the presence of azeotropes, although comphcated further by the closeness in boihng points of the aromatics, t/o-paraffin, and unreacted C -, C -, and Cg-paraffins. 

Catalytic Reforming. Worldwide, approximately 30% of commercial benzene is produced by catalytic reforming, a process ia which aromatic molecules are produced from the dehydrogenation of cycloparaffins, dehydroisomerization of alkyl cyclopentanes, and the cycHzation and subsequent dehydrogenation of paraffins (36). The feed to the catalytic reformer may be a straight-mn, hydrocracked, or thermally cracked naphtha fraction ia the... 

Patents cover a new reforming catalyst based on L-zeoHte which gives a significantly higher yield of BTX, especially benzene, from light paraffinic feeds (11). Other new zeoHtes (12) may also offer advantages over the traditional reforming catalyst supports. 

The mechanistic steps are as follows paraffins dehydrogenate to olefins the olefins oligomerize and cyclize and the cycHcs aromatize. Because the first step is rate controlling, very Httie olefin is actually present. The BTX product is relatively free of nonaromatics and therefore is very desirable as a chemical feed. As in reforming, some C —C2 fuel gas is produced along with a valuable hydrogen stream. Prom a C —feed the BTX product is roughly 35 45 20, respectively. 

Natural gas and crude oils are the main sources for hydrocarbon intermediates or secondary raw materials for the production of petrochemicals. From natural gas, ethane and LPG are recovered for use as intermediates in the production of olefins and diolefms. Important chemicals such as methanol and ammonia are also based on methane via synthesis gas. On the other hand, refinery gases from different crude oil processing schemes are important sources for olefins and LPG. Crude oil distillates and residues are precursors for olefins and aromatics via cracking and reforming processes. This chapter reviews the properties of the different hydrocarbon intermediates—paraffins, olefins, diolefms, and aromatics. Petroleum fractions and residues as mixtures of different hydrocarbon classes and hydrocarbon derivatives are discussed separately at the end of the chapter. 

Paraffins are relatively inactive compared to olefins, diolefins, and aromatics. Few chemicals could be obtained from the direct reaction of paraffins with other reagents. However, these compounds are the precursors for olefins through cracking processes. The C -Cg paraffins and cycloparaffms are especially important for the production of aromatics through reforming. This section reviews some of the physical and chemical properties of C1-C4 paraffins. Long-chain paraffins normally present as mixtures with other hydrocarbon types in different petroleum fractions are discussed later in this chapter. 

These solvents are characterized by a high affinity for aromatics, good thermal stability, and rapid phase separation. The Tetra extraction process by Union Carbide (Figure 2-2) uses tetraethylene glycol as a solvent. The feed (reformate), which contains a mixture of aromatics, paraffins. 

Selecting the naphtha type can be an important processing procedure. For example, a paraffinic-base naphtha is a better feedstock for steam cracking units because paraffins are cracked at relatively lower temperatures than cycloparaffins. Alternately, a naphtha rich in cycloparaffins would be a better feedstock to catalytic reforming units because cyclo-paraffins are easily dehydrogenated to aromatic compounds. Table 2-5 is a typical analysis of naphtha from two crude oil types. 

---