Palladium catalysts reactions

The Heck reaction uses a palladium catalyst reaction to couple aryl halides and alkenes. The product of the reaction is a conjugated aryl alkene. The catalytic cycle, which is somewhat more comphcated than the Suzuki reaction cycle, can be divided into a half dozen steps (Figure 17.6). 

During the reaction, the palladium catalyst is reduced. It is reoxidized by a co-catalyst system such as cupric chloride and oxygen. The products are acryhc acid in a carboxyUc acid-anhydride mixture or acryUc esters in an alcohoHc solvent. Reaction products also include significant amounts of 3-acryloxypropionic acid [24615-84-7] and alkyl 3-alkoxypropionates, which can be converted thermally to the corresponding acrylates (23,98). The overall reaction may be represented by ... 

Vinyl acetate (ethenyl acetate) is produced in the vapor-phase reaction at 180—200°C of acetylene and acetic acid over a cadmium, 2inc, or mercury acetate catalyst. However, the palladium-cataly2ed reaction of ethylene and acetic acid has displaced most of the commercial acetylene-based units (see Acetylene-DERIVED chemicals Vinyl polymers). Current production is dependent on the use of low cost by-product acetylene from ethylene plants or from low cost hydrocarbon feeds. 

Ca.ta.lysis, The most important iadustrial use of a palladium catalyst is the Wacker process. The overall reaction, shown ia equations 7—9, iavolves oxidation of ethylene to acetaldehyde by Pd(II) followed by Cu(II)-cataly2ed reoxidation of the Pd(0) by oxygen (204). Regeneration of the catalyst can be carried out in situ or ia a separate reactor after removing acetaldehyde. The acetaldehyde must be distilled to remove chloriaated by-products. 

Polymerization by G—G Goupling. An aromatic carbon—carbon coupling reaction has been employed for the synthesis of rigid rod-like polyimides from imide-containing dibromo compounds and aromatic diboronic acids ia the presence of palladium catalyst, Pd[P(CgH )2]4 (79,80). 

The first CO route to make adipic acid is a BASF process employing CO and methanol in a two-step process producing dimethyl adipate [627-93-0] which is then hydroly2ed to the acid (43—46). Cobalt carbonyl catalysts such as Co2(CO)g are used. Palladium catalysts can be used to effect the same reactions at lower pressures (47—49). 

Snia Viscosa. Catalytic air oxidation of toluene gives benzoic acid (qv) in ca 90% yield. The benzoic acid is hydrogenated over a palladium catalyst to cyclohexanecarboxyhc acid [98-89-5]. This is converted directiy to cmde caprolactam by nitrosation with nitrosylsulfuric acid, which is produced by conventional absorption of NO in oleum. Normally, the reaction mass is neutralized with ammonia to form 4 kg ammonium sulfate per kilogram of caprolactam (16). In a no-sulfate version of the process, the reaction mass is diluted with water and is extracted with an alkylphenol solvent. The aqueous phase is decomposed by thermal means for recovery of sulfur dioxide, which is recycled (17). The basic process chemistry is as follows ... 

Aromatic Aldehydes. Carbon monoxide reacts with aromatic hydrocarbons or aryl haHdes to yield aromatic aldehydes (see Aldehydes). The reaction of equation 24 proceeds with yields of 89% when carried out at 273 K and 0.4 MPa (4 atm) using a boron trifluoride—hydrogen fluoride catalyst (72), whereas conversion of aryl haHdes to aldehydes in 84% yield by reaction with CO + H2 requires conditions of 423 K and 7 MPa (70 atm) with a homogeneous palladium catalyst (73) and also produces HCl. 

This reaction is favored by moderate temperatures (100—150°C), low pressures, and acidic solvents. High activity catalysts such as 5—10 wt % palladium on activated carbon or barium sulfate, high activity Raney nickel, or copper chromite (nonpromoted or promoted with barium) can be used. Palladium catalysts are recommended for the reduction of aromatic aldehydes, such as that of benzaldehyde to toluene. 

The transmetallation of lithio derivatives with either magnesium bromide or zinc chloride has been employed to increase further their range of synthetic application. While the reaction of l-methyl-2-pyrrolyllithium with iodobenzene in the presence of a palladium catalyst gives only a poor yield (29%) of coupled product, the yield can be dramatically improved (to 96%) by first converting the lithium compound into a magnesium or zinc derivative (Scheme 83) (81TL5319). 

Rosenmund reaction is the action between acid chloride and hydrogen in the presence of palladium catalyst to produce aldehydes... 

Epoxides are normally hydrogenated in preference to saturated ketones but double bonds are usually reduced under these conditions. It is possible in some cases to selectively cleave an epoxide without saturating double bonds by the use of the deactivated catalysts recommended for the partial reduction of acetylenes (see section IV) or by the addition of silver nitrate to the palladium-catalyzed reaction mixture. " ... 

They have also developed a route to 2-allenylindole derivatives (98T13929). When prop-2-ynyl carbonates (76) are reacted with 73 in the presence of palladium catalyst, a cross-coupling reaction occurs to give 77a (46%) and 77b (45%). Under a pressurized carbon monoxide atmosphere (10 atm), the palladium-catalyzed reaction of 73 with 78 provides 79a (60%) and 79b (60%) (2000H2201). In a similar reaction, when the substrate is changed to aryl halides (80), 2-aryl-1-methoxyindoles such as 81a (70%) and 81b (60%) are prepared (97H2309). 

Reaction of the cyclopropyl-substituted pivalate (25) with dimethyl benzylidenema-lonate in the presence of a palladium catalyst gave a mixture of alkylidenecyclo-propane (26) and vinylcyclopropane (27). The ratio of these two adducts is found to be quite sensitive to the choice of ligand and solvent. While triisopropyl phosphite favors the formation of the methylenecyclopropane (26), this selectivity is completely reversed with the use of the bidentate phosphite ligand dptp (12). Interestingly there was no evidence for any products that would have derived from the ring opening of the cyclopropyl-TMM intermediate (Scheme 2.8) [18]. 

Intramolecular cycloadditions of substrates with a cleavable tether have also been realized. Thus esters (37a-37d) provided the structurally interesting tricyclic lactones (38-43). It is interesting to note that the cyclododecenyl system (w = 7) proceeded at room temperature whereas all others required refluxing dioxane. In each case, the stereoselectivity with respect to the tether was excellent. As expected, the cyclohexenyl (n=l) and cycloheptenyl (n = 2) gave the syn adducts (38) and (39) almost exclusively. On the other hand, the cyclooctenyl (n = 3) and cyclododecenyl (n = 7) systems favored the anti adducts (41) and (42) instead. The formation of the endocyclic isomer (39, n=l) in the cyclohexenyl case can be explained by the isomerization of the initial adduct (44), which can not cyclize due to ring-strain, to the other 7t-allyl-Pd intermediate (45) which then ring-closes to (39) (Scheme 2.13) [20]. While the yields may not be spectacular, it is still remarkable that these reactions proceeded as well as they did since the substrates do contain another allylic ester moiety which is known to undergo ionization in the presence of the same palladium catalyst. 

---