Paintable silicone

They must be mounted flush with the ceiling or the walls (or partitions) and sealed with paintable silicone. 

HMIS Health 1, Flammability 1, Reactivity 0 Storage Store below 80 F keep container tightly dosed GP-74 Paintable Silicone Fluid [Genesee Polymers]... 

G-5 -P. See Disodium guanylate GP-28 Silicone Fluid. See Silicone GP-49. See Dimethyidiethoxysilane GP-50-A Modified Silicone Emulsion, GP-51-E Dimethyl Silicone Emulsion, GP-52-E Dimethyl Silicone Emulsion] GP-53-E Dimethyl Silicone Emulsion] GP-54-E Dimethyl Silicone Emulsion] GP-60-AE Silicone Emulsion] GP-60-E Silicone Emulsion. See Dimethicone GP-70-E Paintable Silicone Emulsion. See Silicone emulsion... 

CS-420 [Ducey Chem.] DB-9i Paintable Silicone Emulsion [Genesee Polymers http //www.gpcsiiicones.com]] Defearner 167 [A. Harrison] Defoamer K-20 [Yorkshire Am. http //www.yorkshireamericas. com] Def earner SK [Dongnam Chem. Ind. Ltd http //WWW. dongnamchem. com]... 

Additives used in final products Fiiiers aramid fiber, caicium carbonate, carbon black, carbon fiber, carbon nanotubes, glass beads, glass fiber, iron powder, metal flakes, nano-CaCOj (nucleating agent), PTFE fiber, talc, zinc whisker Antistatics polyetheresteramide, quaternary ammonium compound, superconductive carbon black Release fluoropolymer, N,N -ethylene bisstearamide, paintable silicone Slip PTFE Thermal stabilizer triethanolamine ... 

N,N -ethylene bisstearamide N,N -ethylene bisstearamide fluoropolymer paintable silicone 1,800-3,000 enhanced mechanical properties improved impact resistance faster cycle powder molding process... 

For example, the scratch resistance of talc-filled TPOs modified with 2-3% silicone from masterbatches is significantly improved and visible whitening is suppressed under conditions that damage the same TPO without silicone. Paintability must be verified but a low silicone level (2.5% for example) does not affect paintability, and weathering resistance increases showing less change in aspect than the control without silicone. 

Internal mold release technology is well developed for nylon RIM systems while it is being developed for urethanes. Most urethanes require application of a mold release agent, a wax, a soap or a silicone, after every shot. Many mold releases cannot be added to the urethane reactant streams or the tanks because they react with the urethane chemicals. These reactions have caused problems of build-up in the mold, even with spray-on mold releases, necessitating periodic shutdowns to scrub the mold surfaces. Some newer systems use a third component stream to Introduce mold release at the mix head. Newer Internal mold release systems permit from 0 to 50 urethane shots to be made between applications of external mold release spray to the tool. Monsanto s nylon RIM system contains an internal mold release that is paintable. In certain applications where a high quality smooth show surface is required on a part, a... 

Although many fluids can be developed to act as IMR for RIM, many would fail as commercial products due to their inability to impart paintability to the resulting molded part. In order to rectify this paintability concern with the use of silicone internal mold release agents, a functional moiety is designed into the silicone. This functionality, when correctly specified, reacts into the urethane matrix once the IMR has migrated to the urethane/mold interface. This reactivity causes the IMR to be immobilized in the urethane matrix, thus allowing paintability. 

In order to check the paintability of parts molded with Q2-7119, test panels molded with and without silicone fluid were post-cured, solvent wiped with toluene, primed with PPG Durethane 600 Primer and then top coated with Durethane 300 blue metallic flake or white. Painted samples were exposed for 2 years in Florida Direct Black Box 5° South and then evaluated for appearance and adhesion. Results of these tests showed no difference between control and IMR-containing panels. Paint adhesion was excellent. 

Room temperature cured (RTV) silicones are used as potting compounds and as in situ formed gaskets. These compositions are toughened by the addition of styrene or butyl acrylate which form minute strands of fiber in situ when they polymerize.21 Silicone sealants and coatings are being used in the NASA space shuttles.22 Paintable, fast curing-octoate-cured silicone sealants are also available. Simple tests for utility, based on a filled glass tube, have been described.22... 

Silicone II paintable sealant, commonly used as a caulking material, has the following statement under Directions "Wipe hands and tools with a dry cloth or paper towel, before washing with soap and water." In fact, if you wash with soap and water first, you get a slimy mess. What is there about the structure of silicones that makes this direction important and the behavior expected ... 

Silicone oil can be costly and can reduce the adhesion and paintability of the surface. 

MS Polymers. A relatively new class of adhesives are the two-component MS polymer adhesives, known as moisture-cross-linkable sealants up to know. Due to their excellent elastic properties they are used for elastic bonding. Chemically they are based on silanealkoxy-modified prepolymers such as polyfpropylene glycol). The end groups of these so-called MS polymers are sdanealkoxyl groups which are hydrolyzed by water and then cross-link. In comparison to silicone adhesives, they adhere to all kinds of surfaces without any primer and are paintable in the freshly cured state. 

Non-silicone paintable Light-duty natural release FDA Approved Lubricant Maximum Operating Teiq>erature 500F... 

Non-silicone paintable Fast-drying on cold hot molds... 

Chem. Descrip. Alkyl aralkyl modified silicone fluid Uses Lubricant mold release agent raw material for defoamers Features Paintable exc. release property exc. thermal stability no mineral acid formation... 

Polydimethylsiloxane is the most common release agent and it is also used in slip applications. The major drawback of silicone oil use is its effect on adhesion and paintability. Modified polydimethylsiloxanes seem to be one of the solutions to these problems. There is a large number of modifications, which are most frequently either block copolymers (the other than siloxane block influences compatibility with host polymers), or pol miers having different functional groups, which may react with other components of formulation (mostly matrix polymer). 

The polyether silicone displays adhesion similar to that of silicone sealants but they have other properties of interest. For example, the paintability of polyether silicones is much better than that of silicones because of the polyether content. The property in which this material falls short in comparison to standard silicones is temperature resistance. 

---