Oxidation spectroscopy

XPS X-ray photoelectron spectroscopy [131-137] Monoenergetic x-rays eject electrons from various atomic levels the electron energy spectrum is measured Surface composition, oxidation state... 

Vibrational Spectroscopy. Infrared absorption spectra may be obtained using convention IR or FTIR instrumentation the catalyst may be present as a compressed disk, allowing transmission spectroscopy. If the surface area is high, there can be enough chemisorbed species for their spectra to be recorded. This approach is widely used to follow actual catalyzed reactions see, for example. Refs. 26 (metal oxide catalysts) and 27 (zeolitic catalysts). Diffuse reflectance infrared reflection spectroscopy (DRIFT S) may be used on films [e.g.. Ref. 28—Si02 films on Mo(llO)]. Laser Raman spectroscopy (e.g.. Refs. 29, 30) and infrared emission spectroscopy may give greater detail [31]. 

As with any system, there are complications in the details. The CO sticking probability is high and constant until a 0 of about 0.5, but then drops rapidly [306a]. Practical catalysts often consist of nanometer size particles supported on an oxide such as alumina or silica. Different crystal facets behave differently and RAIRS spectroscopy reveals that CO may adsorb with various kinds of bonding and on various kinds of sites (three-fold hollow, bridging, linear) [307]. See Ref 309 for a discussion of some debates on the matter. In the case of Pd crystallites on a-Al203, it is proposed that CO impinging on the support... 

X-ray photoelectron spectroscopy (XPS), also called electron spectroscopy for chemical analysis (ESCA), is described in section Bl.25,2.1. The most connnonly employed x-rays are the Mg Ka (1253.6 eV) and the A1 Ka (1486.6 eV) lines, which are produced from a standard x-ray tube. Peaks are seen in XPS spectra that correspond to the bound core-level electrons in the material. The intensity of each peak is proportional to the abundance of the emitting atoms in the near-surface region, while the precise binding energy of each peak depends on the chemical oxidation state and local enviromnent of the emitting atoms. The Perkin-Elmer XPS handbook contains sample spectra of each element and bindmg energies for certain compounds [58]. 

In addition to the many applications of SERS, Raman spectroscopy is, in general, a usefiil analytical tool having many applications in surface science. One interesting example is that of carbon surfaces which do not support SERS. Raman spectroscopy of carbon surfaces provides insight into two important aspects. First, Raman spectral features correlate with the electrochemical reactivity of carbon surfaces this allows one to study surface oxidation [155]. Second, Raman spectroscopy can probe species at carbon surfaces which may account for the highly variable behaviour of carbon materials [155]. Another application to surfaces is the use... 

Qin L, Tripathi G N R and Schuler R H 1987 Radiolytic oxidation of 1,2,4-benzenetriol an application of time-resolved resonance Raman spectroscopy to kinetic studies of reaction intermediates J. Chem. Phys. 

Dadap J I, Hu X F, Anderson M H, Downer M C, Lowell J Kand Aktsiperov O A 1996 Optical second-harmonic electroreflectance spectroscopy of a Si(OOOI) metal-oxide-semiconductor structure Phys. Rev. B 53 R7607-9... 

Figure Bl.22.4. Differential IR absorption spectra from a metal-oxide silicon field-effect transistor (MOSFET) as a fiinction of gate voltage (or inversion layer density, n, which is the parameter reported in the figure). Clear peaks are seen in these spectra for the 0-1, 0-2 and 0-3 inter-electric-field subband transitions that develop for charge carriers when confined to a narrow (<100 A) region near the oxide-semiconductor interface. The inset shows a schematic representation of the attenuated total reflection (ATR) arrangement used in these experiments. These data provide an example of the use of ATR IR spectroscopy for the probing of electronic states in semiconductor surfaces [44]-...

XPS X-ray photoelectron spectroscopy Absorption of a photon by an atom, followed by the ejection of a core or valence electron with a characteristic binding energy. Composition, oxidation state, dispersion... 

Wang L S 2000 Photodetachment photoelectron spectroscopy of transition metal oxide species Photoionization and Photodetaohment Advanced Series in Physical Chemistry 10, ed C Y Ng (Singapore World Scientific)... 

In voltammetry a time-dependent potential is applied to an electrochemical cell, and the current flowing through the cell is measured as a function of that potential. A plot of current as a function of applied potential is called a voltammogram and is the electrochemical equivalent of a spectrum in spectroscopy, providing quantitative and qualitative information about the species involved in the oxidation or reduction reaction.The earliest voltammetric technique to be introduced was polarography, which was developed by Jaroslav Heyrovsky... 

One other very important attribute of photoemitted electrons is the dependence of their kinetic energy on chemical environment of the atom from which they originate. This feature of the photoemission process is called the chemical shift of and is the basis for chemical information about the sample. In fact, this feature of the xps experiment, first observed by Siegbahn in 1958 for a copper oxide ovedayer on a copper surface, led to his original nomenclature for this technique of electron spectroscopy for chemical analysis or esca. 

Transmission Fourier Transform Infrared Spectroscopy. The most straightforward method for the acquisition of in spectra of surface layers is standard transmission spectroscopy (35,36). This approach can only be used for samples which are partially in transparent or which can be diluted with an in transparent medium such as KBr and pressed into a transmissive pellet. The extent to which the in spectral region (typically ca 600 4000 cm ) is available for study depends on the in absorption characteristics of the soHd support material. Transmission ftir spectroscopy is most often used to study surface species on metal oxides. These soHds leave reasonably large spectral windows within which the spectral behavior of the surface species can be viewed. 

Elemental chemical analysis provides information regarding the formulation and coloring oxides of glazes and glasses. Energy-dispersive x-ray fluorescence spectrometry is very convenient. However, using this technique the analysis for elements of low atomic numbers is quite difficult, even when vacuum or helium paths are used. The electron-beam microprobe has proven to be an extremely useful tool for this purpose (106). Emission spectroscopy and activation analysis have also been appHed successfully in these studies (101). 

Triphenylphosphine oxide [791-28-6], C gH OP, and triphenyl phosphate [115-86-6], C gH O P, as model phosphoms flame retardants were shown by mass spectroscopy to break down in a flame to give small molecular species such as PO, HPO2, and P2 (33—35). The rate-controlling hydrogen atom concentration in the flame was shown spectroscopically to be reduced when these phosphoms species were present, indicating the existence of a vapor-phase mechanism. 

Stability of the chromophore was observed usiag uv-vis spectroscopy, the authors conclude that this sol—gel method of chromophore encapsulation does not provide any real thermal or oxidative protection in either the covalendy or noncovalently bonded state. 

Analyses of alloys or ores for hafnium by plasma emission atomic absorption spectroscopy, optical emission spectroscopy (qv), mass spectrometry (qv), x-ray spectroscopy (see X-ray technology), and neutron activation are possible without prior separation of hafnium (19). Alternatively, the combined hafnium and zirconium content can be separated from the sample by fusing the sample with sodium hydroxide, separating silica if present, and precipitating with mandelic acid from a dilute hydrochloric acid solution (20). The precipitate is ignited to oxide which is analy2ed by x-ray or emission spectroscopy to determine the relative proportion of each oxide. 

Chemical Analysis. Plasma oxidation and other reactions often are used to prepare samples for analysis by either wet or dry methods. Plasma excitation is commonly used with atomic emission or absorption spectroscopy for quaUtative and quantitative spectrochemical analysis (86—88). 

Other Coordination Complexes. Because carbonate and bicarbonate are commonly found under environmental conditions in water, and because carbonate complexes Pu readily in most oxidation states, Pu carbonato complexes have been studied extensively. The reduction potentials vs the standard hydrogen electrode of Pu(VI)/(V) shifts from 0.916 to 0.33 V and the Pu(IV)/(III) potential shifts from 1.48 to -0.50 V in 1 Tf carbonate. These shifts indicate strong carbonate complexation. Electrochemistry, reaction kinetics, and spectroscopy of plutonium carbonates in solution have been reviewed (113). The solubiUty of Pu(IV) in aqueous carbonate solutions has been measured, and the stabiUty constants of hydroxycarbonato complexes have been calculated (Fig. 6b) (90). 

Only slightly less accurate ( 0.3—0.5%) and more versatile in scale are other titration techniques. Plutonium maybe oxidized in aqueous solution to PuO " 2 using AgO, and then reduced to Pu" " by a known excess of Fe", which is back-titrated with Ce" ". Pu" " may be titrated complexometricaHy with EDTA and a colorimetric indicator such as Arsenazo(I), even in the presence of a large excess of UO " 2- Solution spectrophotometry (Figs. 4 and 5) can be utilized if the plutonium oxidation state is known or controlled. The spectrophotometric method is very sensitive if a colored complex such as Arsenazo(III) is used. Analytically usehil absorption maxima and molar absorption coefficients ( s) are given in Table 10. Laser photoacoustic spectroscopy has been developed for both elemental analysis and speciation (oxidation state) at concentrations of lO " — 10 M (118). Chemical extraction can also be used to enhance this technique. 

---