Of aluminium

C22H23N3O9. An organic reagent used for the detection and estimation of aluminium. It is a brownish-red powder, soluble in water which gives a red lake with aluminium which can be estimated colorimetrically. It can also be used for detecting scandium and indium. 

Prepared by the dehydration of benzamide. Hydrolysed by dilute acids and alkalis to benzoic acid. Good solvent. benzopheDone,C]3HioO,PhC(0)Ph. Colourless rhombic prisms, m.p. 49 C, b.p. 306°C. Characteristic smell. It is prepared by the action of benzoyl chloride upon benzene in the presence of aluminium chloride (Friedel-Crafts reaction) or by the oxidation of di-phenylmethane. It is much used in perfumery. Forms a kelyl with sodium. 

Figure 2. Schematic of the experimental arrangement used for inspection of aluminium plate. Lenses are shown as LI and L2, mirrors as Ml, M2 and M3, and liquid crystal cell as LC...

On Line Eccentricity Measurement during Fabrication of Aluminium Tubes. 

Finally, in 1985, the results of an extensive investigation in which adsorjDtion took place onto an aluminium oxide layer fonned on a film of aluminium deposited in vacuo onto a silicon wafer was published by Allara and Nuzzo 1127, 1281. Various carboxylic acids were dissolved in high-purity hexadecane and allowed to adsorb from this solution onto the prepared aluminium oxide surface. It was found that for chains with more than 12 carbon atoms, chains are nearly in a vertical orientation and are tightly packed. For shorter chains, however, no stable monolayers were found. The kinetic processes involved in layer fonnation can take up to several days. 

In each of the examples given so far each element has achieved a noble gas configuration as a result of electron sharing. There are. however, many examples of stable covalent compounds in which noble gas configurations are not achieved, or are exceeded. In the compounds of aluminium, phosphorus and sulphur, shown below, the central atoms have 6. 10 and 12 electrons respectively involved in bondinc... 

Metals in higher oxidation states form halides which are essentially covalent, for example AICI3, SnCl, FeClj when these compounds dissolve in water they do so by a strongly exothermic process. Indeed it is perhaps incorrect to think of this only as a dissolution process, since it is more like a chemical reaction—but to differentiate for a particular substance is not easy, as we shall see. The steps involved in the case of aluminium chloride can be represented as... 

The electrode potential of aluminium would lead us to expect attack by water. The inertness to water is due to the formation of an unreactive layer of oxide on the metal surface. In the presence of mercury, aluminium readily forms an amalgam (destroying the original surface) which is. therefore, rapidly attacked by water. Since mercury can be readily displaced from its soluble salts by aluminium, contact with such salts must be avoided if rapid corrosion and weakening of aluminium structures is to be prevented. 

A white gelatinous precipitate of aluminium hydroxide is obtained when an alkali is added to an aqueous solution of an aluminium salt. Addition of an excess of caustic alkali causes the precipitate to redissolve, the whole process being reversed by the addition of a strong acid the actual substance present at any time depending on... 

Sheet aluminium can be given a colour by a similar process. The aluminium is first made the anode in a bath of chromic acid (p. 377) when, instead of oxygen being evolved, the aluminium becomes coated with a very adherent film of aluminium oxide which is very adsorbent. If a dye is added to the bath the oxide film is coloured, this colour being incorporated in a film which also makes the remaining aluminium resistant to corrosion. This process is called anodising aluminium. 

Aluminium nitride can also be prepared by heating a mixture of aluminium oxide and carbon in nitrogen in an electric arc furnace ... 

It is stable up to 2000 K and melts under pressure at 2500 K. The crystal structure of aluminium nitride resembles that of boron nitride and diamond, but unlike both of these it is rapidly and exothermically hydrolysed by cold water ... 

Addition of ammonium hydroxide to a solution of an aluminium salt gives a white gelatinous precipitate of aluminium hydroxide, Al(OH)3, insoluble in excess. Sodium hydroxide gives the same precipitate, but in this case, it does dissolve in excess. 

Alternatively pure hydrogen sulphide is obtained by the hydrolysis of aluminium(III) sulphide ... 

Notice that the acidic character is associated with the ability of aluminium to increase its covalency from three in the oxide to six in the hydroxoaluminate ion, [Al(OH)g] the same abihty to increase covalency is found in other metals whose oxides are amphoteric, for example... 

Scandium is not an uncommon element, but is difficult to extract. The only oxidation state in its compounds is -I- 3, where it has formally lost the 3d 4s electrons, and it shows virtually no transition characteristics. In fact, its chemistry is very similar to that of aluminium (for example hydrous oxide SC2O3, amphoteric forms a complex [ScFg] chloride SCCI3 hydrolysed by water). 

In the following preparation to illustrate the Meen.vein-Pormdorf-Verley reduc tion, a solution of benzophenone in isopropanol is rapidly reduced in the presence of aluminium isopropoxide to benzhydrol (CaHs)2CO (C Hj)jCH OH. It is clear that the aluminium isopropoxide must take some essential part in this reaction, for benzophenone when dissolved even in cold isopropanol with a trace of acetic acid is reduced to tetraphenylethyleneglycol (p. 150). 

Place in the flask 2 g. of benzophenone, 15 ml. of isopropanol and 2 5 g. of aluminium isopropoxide. This mixture has now to be heated gently under reflux so that the temperature registered by the thermometer in the column does not exceed 80°, i.e., so that only acetone distils. For this purpose, the flask should preferably be heated in an oil-bath direct heating, even over an asbestos sheet, may cause local overheating and decomposition the use of a water-bath on the other hand may make the column undesirably damp. 

TTie true ketones, in which the >CO group is in the side chain, the most common examples being acetophenone or methyl phenyl ketone, C HjCOCH, and benzophenone or diphenyl ketone, C HjCOC(Hj. These ketones are usually prepared by a modification of the Friedel-Crafts reaction, an aromatic hydrocarbon being treated with an acyl chloride (either aliphatic or aromatic) in the presence of aluminium chloride. Thus benzene reacts with acetyl chloride... 

The Friedel-Crafts Reaction, in which an aromatic hydrocarbon reacts with an alkyl halide under the influence of aluminium chloride ... 

Meanwhile, the organic compound can be prepared for analysis whilst the sealed end C (Fig. 72) of the Carius tube has been cooling dow n. For this purpose, thoroughly clean and dry a small tube, which is about 6 cm. long and 8-10 mm. w ide. Weigh it carefully, supporting it on the balance pan either by means of a small stand of aluminium foil, or by a short section of a perforated rubber stopper (Fig. 73 (A) and (B) respectively) alternatively the tube may be placed in a small beaker on the balance pan, or suspended above the pan by a small hooked wire girdle. 

---