Molecular weight polymerization reactors

Free-Radical Polymerization Sensitivity of Conversion and Molecular Weights to Reactor Conditions... 

Polymer Synthesis. Copolymers of alkylacrylamide (R) and acrylamide (AM), which we called RAM, were prepared with a micellar polymerization technique (4). A micellar surfactant solution was used to disperse the hydrophobic alkylacrylamide monomer into an aqueous phase that contained acrylamide. The monomers were polymerized with a standard free-radical initiator (e.g., potassium persulfate) or a redox initiator to yield the desired random copolymer. Varied temperature and initiator concentrations were used to provide polymers of different molecular weights. Polymerizations were taken to essentially complete conversion. Compositions, in terms of hydrophobe level reported in this chapter, were based on amounts charged to the reactor. Further details on the synthesis and structure of these RAM polymers... 

Lee, K.H. and J.P. Marano. Free-Radical Polymerization Sensitivity of Conversion and Molecular Weights to Reactor Conditions Polymerization Reactors and Processes (ACS Symposium Series 104, J.N. Henderson and T.C. Bouton, eds.), American Chemical Society, Washington, D.C., (1979), 223-251. 

Before we can explore how reactor conditions can be chosen, we require some measure of reactor performance. For polymerization reactors, the most important measure of performance is the distribution of molecular weights in the polymer product. The distribution of molecular weights dictates the mechanical properties of the polymer. For other types of reactors, three important parameters are used to describe their performance ... 

In a typical adiabatic polymerization, approximately 20 wt % aqueous acrylamide is charged into a stainless steel reactor equipped with agitation, condenser, and cooling jacket or coils. To initiate the polymerization, an aqueous solution of sodium bisulfite [7631-90-5] is added, followed by the addition of a solution of ammonium persulfate [7727-54-0] N2HgS20g. As the polymerization proceeds, the temperature rises to about 90°C, and then begins to fall at the end of the polymerization. The molecular weight obtained depends primarily on the initiator concentration employed. 

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

The majority of thermal polymerizations are carried out as a batch process, which requires a heat-up and a cool down stage. Typical conditions are 250—300°C for 0.5—4 h in an oxygen-free atmosphere (typically nitrogen) at approximately 1.4 MPa (200 psi). A continuous thermal polymerization has been reported which utilizes a tubular flow reactor having three temperature zones and recycle capabiHty (62). The advantages of this process are reduced residence time, increased production, and improved molecular weight control. Molecular weight may be controlled with temperature, residence time, feed composition, and polymerizate recycle. 

Molecular Weight Distribution. In industry, the MWD of PE resins is often represented by the value of the melt flow ratio (MER) as defined in Table 2. The MER value of PE is primarilly a function of catalyst type. Phillips catalysts produce PE resins with a broad MWD and their MER usually exceeds 100 Ziegler catalysts provide resins with a MWD of a medium width (MFR = 25-50) and metallocene catalysts produce PE resins with a narrow MWD (MFR = 15-25). IfPE resins with especially broad molecular weight distributions are needed, they can be produced either by using special mixed catalysts or in a series of coimected polymerization reactors operating under different reaction conditions. 

Some slurry processes use continuous stirred tank reactors and relatively heavy solvents (57) these ate employed by such companies as Hoechst, Montedison, Mitsubishi, Dow, and Nissan. In the Hoechst process (Eig. 4), hexane is used as the diluent. Reactors usually operate at 80—90°C and a total pressure of 1—3 MPa (10—30 psi). The solvent, ethylene, catalyst components, and hydrogen are all continuously fed into the reactor. The residence time of catalyst particles in the reactor is two to three hours. The polymer slurry may be transferred into a smaller reactor for post-polymerization. In most cases, molecular weight of polymer is controlled by the addition of hydrogen to both reactors. After the slurry exits the second reactor, the total charge is separated by a centrifuge into a Hquid stream and soHd polymer. The solvent is then steam-stripped from wet polymer, purified, and returned to the main reactor the wet polymer is dried and pelletized. Variations of this process are widely used throughout the world. 

The Amoco reactor operates at 70—80°C and 2 MPa (300 psi) reactor pressure. The existence of several partially isolated compartments allows a semi-iadependent control of temperature as well as comonomer and hydrogen concentrations within each section, which ia turn offers a substantial control of the molecular weight and MWD of resias. Amoco technology also accommodates a large variety of polymerization catalysts, including Phillips and Ziegler catalysts. 

Processes for HDPE with Broad MWD. Synthesis of HDPE with a relatively high molecular weight and a very broad MWD (broader than that of HDPE prepared with chromium oxide catalysts) can be achieved by two separate approaches. The first is to use mixed catalysts containing two types of active centers with widely different properties (50—55) the second is to employ two or more polymerization reactors in a series. In the second approach, polymerization conditions in each reactor are set drastically differendy in order to produce, within each polymer particle, an essential mixture of macromolecules with vasdy different molecular weights. Special plants, both slurry and gas-phase, can produce such resins (74,91—94). 

Solution Polymerization. In this process an inert solvent is added to the reaction mass. The solvent adds its heat capacity and reduces the viscosity, faciUtating convective heat transfer. The solvent can also be refluxed to remove heat. On the other hand, the solvent wastes reactor space and reduces both rate and molecular weight as compared to bulk polymerisation. Additional technology is needed to separate the polymer product and to recover and store the solvent. Both batch and continuous processes are used. 

Solution Polymerization. Solution polymerization of vinyl acetate is carried out mainly as an intermediate step to the manufacture of poly(vinyl alcohol). A small amount of solution-polymerized vinyl acetate is prepared for the merchant market. When solution polymerization is carried out, the solvent acts as a chain-transfer agent, and depending on its transfer constant, has an effect on the molecular weight of the product. The rate of polymerization is also affected by the solvent but not in the same way as the degree of polymerization. The reactivity of the solvent-derived radical plays an important part. Chain-transfer constants for solvents in vinyl acetate polymerizations have been tabulated (13). Continuous solution polymers of poly(vinyl acetate) in tubular reactors have been prepared at high yield and throughput (73,74). 

A factor in addition to the RTD and temperature distribution that affects the molecular weight distribution (MWD) is the nature of the chemical reaciion. If the period during which the molecule is growing is short compared with the residence time in the reactor, the MWD in a batch reactor is broader than in a CSTR. This situation holds for many free radical and ionic polymerization processes where the reaction intermediates are very short hved. In cases where the growth period is the same as the residence time in the reactor, the MWD is narrower in batch than in CSTR. Polymerizations that have no termination step—for instance, polycondensations—are of this type. This topic is treated by Denbigh (J. Applied Chem., 1, 227 [1951]). 

Low molecular weight olefins ranging from to Q, are produced by the polymerization of propylene or butylenes over a supported phosphorie acid catalyst. The product of this polymerization is a series of highly branched olefins ranging from dimers to pentamers. Some fragmentation of the polymers formed takes place in the reactor, so appreciable quantities of olefins are obtained which are not integral multiples of the monomer units. 

Continuous polymerization processes for PA-6,6 have been reported for over 30 years.5,6,28 Prepolymerization in tubular (Fig. 3.21) or baffled reactors is particularly well suited to continuous polymerization. The polymerization of prepolymers to high-molecular-weight materials in a continuous process is more difficult to control as small differences is molecular weights result in large differences in viscosities. Viscosity differences result in different hold-up times in die reactor and thus nonhomogeneous products. 

---