Cell, membranes

In 1988 diaphragm cells accounted for 76% of all U.S. chlorine production, mercury cells for 17%, membrane cells for 5%, and all other production methods for 2%. Corresponding statistics for Canadian production are diaphragm cells, 81% mercury cells, 15% and membrane cells, 4% (5). for a number of reasons, including concerns over mercury pollution, recent trends are away from mercury cell production toward the more environmentally acceptable membrane cells, which also produce higher quality product and have favorable economics. 

Conversion of aqueous NaCl to Cl and NaOH is achieved in three types of electrolytic cells the diaphragm cell, the membrane cell, and the mercury cell. The distinguishing feature of these cells is the manner by which the electrolysis products are prevented from mixing with each other, thus ensuring generation of products having proper purity. 

Chloiine is pioduced at the anode in each of the three types of electrolytic cells. The cathodic reaction in diaphragm and membrane cells is the electrolysis of water to generate as indicated, whereas the cathodic reaction in mercury cells is the discharge of sodium ion, Na, to form dilute sodium amalgam. 

Separation of the anode and cathode products in diaphragm cells is achieved by using asbestos [1332-21 -4] or polymer-modified asbestos composite, or Polyramix deposited on a foraminous cathode. In membrane cells, on the other hand, an ion-exchange membrane is used as a separator. Anolyte—catholyte separation is realized in the diaphragm and membrane cells using separators and ion-exchange membranes, respectively. The mercury cells contain no diaphragm the mercury [7439-97-6] itself acts as a separator. 

The catholyte from diaphragm cells typically analyzes as 9—12% NaOH and 14—16% NaCl. This ceUHquor is concentrated to 50% NaOH in a series of steps primarily involving three or four evaporators. Membrane cells, on the other hand, produce 30—35% NaOH which is evaporated in a single stage to produce 50% NaOH. Seventy percent caustic containing very Httie salt is made directiy in mercury cell production by reaction of the sodium amalgam from the electrolytic cells with water in denuders. 

Component Mercury cell Diaphragm cell Membrane cell... 

Current Efficiency. Current efficiency for caustic production in diaphragm and membrane cells can be estimated from collection of a known amount of caustic over a period of time and from a knowledge of the number of coulombs of electricity passed during that time period. An alternative method involves analysis of the gases evolved during electrolysis and determining the anolyte composition. Material balance considerations (7) show the expression for the caustic efficiency for membrane cells to be... 

The electrolysis of potassium chloride [7447-40-7] KCl, to produce chlorine and potassium hydroxide in membrane cells requires similar but unique membranes. Commercial membranes currendy employed in high performance membrane electroly2ers include Du Pont s Nafion 900 series and Asahi Glass s Plemion 700 series. 

A summary of the current membrane cell technologies is provided in Table 13. 

Table 13. Summary of Current Membrane Cell Technologies...

Catalytic cathodes in membrane cell operations exhibit a voltage savings of 100—200 mV and a life of about 2 + yr using ultrapure brine. However, trace impurities such as iron from the caustic recirculation loop can deposit on the cathode and poison the coating, thereby reducing its economic life. 

Removal of brine contaminants accounts for a significant portion of overall chlor—alkali production cost, especially for the membrane process. Moreover, part or all of the depleted brine from mercury and membrane cells must first be dechlorinated to recover the dissolved chlorine and to prevent corrosion during further processing. In a typical membrane plant, HCl is added to Hberate chlorine, then a vacuum is appHed to recover it. A reducing agent such as sodium sulfite is added to remove the final traces because chlorine would adversely react with the ion-exchange resins used later in the process. Dechlorinated brine is then resaturated with soHd salt for further use. 

The choice of technology, the associated capital, and operating costs for a chlor—alkaU plant are strongly dependent on local factors. Especially important are local energy and transportation costs, as are environmental constraints. The primary difference ia operating costs between diaphragm, mercury, and membrane cell plants results from variations ia electricity requirements for the three processes (Table 25) so that local energy and steam costs are most important. 

Because of limited commercial experience with anode coatings in membrane cells, commercial lifetimes have yet to be defined. Expected lifetime is 5—8 years. In some cases as of this writing (ca 1995), 10-years performance has already been achieved. Actual lifetime is dictated by the membrane replacement schedule, cell design, the level of oxygen in the chlorine gas, and by the current density at which the anode is operated. 

The latitude that titanium affords the cell designer has made a wide variety of monopolar and bipolar membrane cell designs possible. 

High yields of NaOCl are obtained electrolyticaHy by oxidation of CT at dimensionally stable anodes (219). Sodium hypochlorite is prepared using small diaphragmless or membrane cells, with a capacity of 1—150 kg/d of equivalent CI2, which produce a dilute hypochlorite solution of 1—3 and 5—6 g/L from seawater and brine, respectively (see Chemicals from brine). They are employed in sewage and wastewater treatment and in commercial laundries, large swimming pools, and aboard ships. 

Fig. 1. Flow diagram for chlor-alkali production by a membrane cell process.

Mild steel cathodes are used extensively in chlor-alkah and chlorate cells. Newer activated cathode materials have been developed that decrease cell voltages about 0.2 V below that for cells having mild steel cathodes. Some activated cathodes have operated in production membrane cells for three years with only minor increases in voltage (17). Activated cathodes can decrease the energy consumption for chlorine—caustic production by 5 to 6.5%. 

There are three main technologies available for carrying out this process diaphragm cells, mercury cells, and membrane cells. Membrane cells are the most recent development, and are generally chosen for new production capacity. 

Membrane cells are the state of the art chlor-alkah technology as of this writing. There are about 14 different membrane cell designs in use worldwide (34). The operating characteristics of some membrane cells are given in Table 3. The membranes are perfluorosulfonate polymers, perfluorocarboxylate polymers, and combinations of these polymers. Membranes are usually reinforced with a Teflon fabric. Many improvements have been made in membrane cell designs to accommodate membranes in recent years (35,36). 

Membrane cells generally produce high quaUty chlorine. Higher than normal H2 concentrations in CI2 indicate that holes exist in the membrane. 

There have been a number of cell designs tested for this reaction. Undivided cells using sodium bromide electrolyte have been tried (see, for example. Ref. 29). These have had electrode shapes for in-ceU propylene absorption into the electrolyte. The chief advantages of the electrochemical route to propylene oxide are elimination of the need for chlorine and lime, as well as avoidance of calcium chloride disposal (see Calcium compounds, calcium CHLORIDE Lime and limestone). An indirect electrochemical approach meeting these same objectives employs the chlorine produced at the anode of a membrane cell for preparing the propylene chlorohydrin external to the electrolysis system. The caustic made at the cathode is used to convert the chlorohydrin to propylene oxide, reforming a NaCl solution which is recycled. Attractive economics are claimed for this combined chlor-alkali electrolysis and propylene oxide manufacture (135). 

---