Melting aluminium compounds

Calculated from the mean square displacement of the lattice atoms measured by X-ray diffraction. Tablett.l-itl Melting point of aluminium compounds... 

In this instance the crystalline dimethylamine complex decomposes as it melts (44°). For the reasons already discussed in connection with the analogous aluminium compound Me2AlNMc2, dimethylaminomethyl-beryllium associates. Up to 50° it is a poly- or oligo-meric glass then it melts between 51 and 54°. As vapour or in solution it is a cyclic trimer 3.36. 

The melting and boiling points of the aluminium halides, in contrast to the boron compounds, are irregular. It might reasonably be expected that aluminium, being a more metallic element than boron, would form an ionic fluoride and indeed the fact that it remains solid until 1564 K. when it sublimes, would tend to confirm this, although it should not be concluded that the fluoride is, therefore, wholly ionic. The crystal structure is such that each aluminium has a coordination number of six, being surrounded by six fluoride ions. 

The alloy aluminium-4 wt% copper forms the basis of the 2000 series (Duralumin, or Dural for short). It melts at about 650°C. At 500°C, solid A1 dissolves as much as 4 wt% of Cu completely. At 20°C its equilibrium solubility is only 0.1 wt% Cu. If the material is slowly cooled from 500°C to 20°C, 4 wt% - 0.1 wt% = 3.9 wt% copper separates out from the aluminium as large lumps of a new phase not pure copper, but of the compound CuAlj. If, instead, the material is quenched (cooled very rapidly, often by dropping it into cold water) from 500°C to 20°C, there is not time for the dissolved copper atoms to move together, by diffusion, to form CuAlj, and the alloy remains a solid solution. 

The starting material for the above step may be prepared as follows 5 g (0.016 mol) of N -(p-methoxyphenyl)-p-chlorobenzhydrazide hydrochloride and 4.75 g (0.018 mol) of benzyl levulinoyloxyacetate were heated In 25 ml of glacial acetic acid for 3 hours at 80°C. The solvent was then evaporated off under vacuum. The residue was taken up in chloroform and the solution was washed neutral by shaking with sodium bicarbonate solution and thereafter with water. After drying the chloroform solution, this was subjected to chromatography on aluminium oxide, the eluate was concentrated by evaporation and the viscous oil remaining as residue was crystallized by adding ether. The compound melted at 94°-95 t. The yield was 4.1 g which corresponds to 50.7% of the theoretical yield. 

As new compounds, very limited research has been done to evaluate the biological effects of ionic liquids. The topical effect of [EMIM]C1/A1C13 melts and [EMIMjCl on the integument of laboratory rat has been investigated. The study reports that [EMIMjCl is not in itself responsible for tissue damage. However, the chloroaluminate salt can induce tissue irritation, inflammation, and necrosis, due to the presence of aluminium chloride. However, treatments for aluminium chloride and hydrochloric acid are well documented. This study needs to be expanded to the other ionic liquids, and their toxicity need to be investigated [46]. 

Copper oxides give rise to numerous accidents. When copper (II) oxide was heated with boron, it gave a highly violent reaction, which caused the melting of the Pyrex container. This is true for alkali metals and titanium as well as aluminium. The reactions lead to liquid metal copper. The emissions of glowing compounds make the reaction very dangerous. 

At the m.p. of aluminium (600°C) an aluminium-sheathed palladium thermocouple formed an alloy with a flash and an exotherm to 2800°C [1]. The use of thin layers of palladium or platinum on aluminium foil or wire as igniters derives from the intense heat of alloy formation, which is sufficient to melt the intermetallic compounds [2],... 

Table 5.64. Highest melting points (°C) in the alloys of aluminium and indium with compound-forming elements of the 4th and 6th rows of the Periodic Table. 

Abstract The term Lewis acid catalysts generally refers to metal salts like aluminium chloride, titanium chloride and zinc chloride. Their application in asymmetric catalysis can be achieved by the addition of enantiopure ligands to these salts. However, not only metal centers can function as Lewis acids. Compounds containing carbenium, silyl or phosphonium cations display Lewis acid catalytic activity. In addition, hypervalent compounds based on phosphorus and silicon, inherit Lewis acidity. Furthermore, ionic liquids, organic salts with a melting point below 100 °C, have revealed the ability to catalyze a range of reactions either in substoichiometric amount or, if used as the reaction medium, in stoichiometric or even larger quantities. The ionic liquids can often be efficiently recovered. The catalytic activity of the ionic liquid is explained by the Lewis acidic nature of then-cations. This review covers the survey of known classes of metal-free Lewis acids and their application in catalysis. 

Renz 4 describes an additive compound of indium trichloride and pyridine, tripyridino-indium trichloride, [In(C5H5N)3]Cl3, which is prepared by adding pyridine to a solution of indium trichloride in alcohol. After standing for a short time, small needle-shaped crystals separate of melting-point 253° C. The compound is not hygroscopic like indium chloride, is somewhat sparingly soluble in alcohol, and is insoluble in ether. It decomposes on warming with water with formation of indium hydroxide, In(OH)3. Aluminium trichloride and iron trichloride form similar addition products. 

Aluminium oxide is an ionic compound. When it is melted the ions become mobile, as the strong electrostatic forces of attraction between them are broken by the input of heat energy. During electrolysis the negatively charged oxide ions are attracted to the anode (the positive electrode), where they lose electrons (oxidation). 

Many of the following powdered metals reacted violently or explosively with fused ammonium nitrate below 200°C aluminium, antimony, bismuth, cadmium, chromium, cobalt, copper, iron, lead, magnesium, manganese, nickel, tin, zinc also brass and stainless steel. Mixtures with aluminium powder are used as the commercial explosive Ammonal. Sodium reacts to form the yellow explosive compound sodium hyponitrite, and presence of potassium sensitises the nitrate to shock [1]. Shock-sensitivity of mixtures of ammonium nitrate and powdered metals decreases in the order titanium, tin, aluminium, magnesium, zinc, lead, iron, antimony, copper [2], Contact between molten aluminium and the salt is violently explosive, apparently there is a considerable risk of this happening in scrap re melting [3]. 

---