Elastomers mechanical properties

Natural mbber crystallizes on elongation—a phenomenon called strain-induced crystallization—what enhances mechanical properties. However, a filler in the form of carbon black is typically added to natural rubber to additionally modify the mechanical properties. Elastomers which cannot undergo strain-induced crystallization contain even more fillers. Carbon black is used in such cases also, but silicone rubbers are filled with silica. 

Nitrile mbber finds broad application in industry because of its excellent resistance to oil and chemicals, its good flexibility at low temperatures, high abrasion and heat resistance (up to 120°C), and good mechanical properties. Nitrile mbber consists of butadiene—acrylonitrile copolymers with an acrylonitrile content ranging from 15 to 45% (see Elastomers, SYNTHETIC, NITRILE RUBBER). In addition to the traditional applications of nitrile mbber for hoses, gaskets, seals, and oil well equipment, new applications have emerged with the development of nitrile mbber blends with poly(vinyl chloride) (PVC). These blends combine the chemical resistance and low temperature flexibility characteristics of nitrile mbber with the stability and ozone resistance of PVC. This has greatly expanded the use of nitrile mbber in outdoor applications for hoses, belts, and cable jackets, where ozone resistance is necessary. 

Rocket Propellants. SoHd rocket propellants are mostly based on chemically cross-linked polymeric elastomers to provide the mechanical properties required in launchings and the environmental conditions experienced in storage, shipment, and handling (see Elastomers, synthetic). Double-and triple-based nitrocellulose propellants are also employed as rocket propellants. 

Table 12. Selected Mechanical Properties of 4GT—PTMEP-T Elastomers...

Polysulfides. The polysulftde elastomer, best known under the trade name Thiokol, represents the earliest commercially developed synthetic mbber, developed ia 1930 by J. C. Patrick as a highly solvent and age-resistant elastomer (15). It is stiH considered the most solvent-resistant mbber, but its poor mechanical properties provide a serious disadvantage (see Polymers containing sulfur). 

Selection of the right elastomer has to take iato account not only the low temperature resistance, the elastic properties, and mechanical properties, but also price, which can vary widely ia specialty elastomers. 

Mechanical Properties. Typical properties of ethylen—acryhc elastomers, like those of other compounded mbbers, vary widely with ... 

The classification given in Table 1 is based on the process, ie, thermosetting or thermoplastic, by which polymers in general are formed into usehil articles and on the mechanical properties, ie, rigid, flexible, or mbbery, of the final product. AH commercial polymers used for molding, extmsion, etc, fit into one of these six classifications the thermoplastic elastomers are the newest. 

It is necessary to consider the micro-mechanical processes of polymer glasses and elastomers separately as their mechanical properties are so different. In addition, cross-linking profoundly affects the deformation processes in glasses but very little is known about the micro-mechanical processe.s that occur in single phase cross-linked glasses so the latter materials will not be discussed further. 

Reinforcing fillers (active) Fumed Silica (Si02) precipitated calcium carbonate (CaCOi) carbon black Thixotropic reinforcing agents (non-slump), adjustment of mechanical properties (cohesion) provide toughness to the elastomer as opposed to brittle materials. 

Both the dipolymers and terpolymers have excellent resistance to hydrocarbons found m petroleum-based fuels and lubricants The 69 5% F terpolymer resists swellmg m blended fuels that contain metlianol and can be used in contact with certain phosphate ester-based hydraulic fluids Terpolymers are preferred for contact with aromatic solvents, although either type performs well in higher alcohols VDF-based elastomers dissolve m polar aprotic solvents such as ketones, esters, amides, and certam ethers These elastomers are therefore not suitable for contact with fluids that contain substantial amounts of these solvents because of excessive swell and consequent loss of mechanical properties... 

In nonrigid ionomers, such as elastomers in which the Tg is situated below ambient temperature, even greater changes can be produced in tensile properties by increase of ion content. As one example, it has been found that in K-salts of a block copolymer, based on butyl acrylate and sulfonated polystyrene, both the tensile strength and the toughness show a dramatic increase as the ion content is raised to about 6 mol% [10]. Also, in Zn-salts of a butyl acrylate/acrylic acid polymer, the tensile strength as a function of the acrylic acid content was observed to rise from a low value of about 3 MPa for the acid copolymer to a maximum value of about 15 MPa for the ionomer having acrylic acid content of 5 wt% [II]. Other examples of the influence of ion content on mechanical properties of ionomers are cited in a recent review article [7],... 

Natural rubber was the only polymer for elastomer production until the advent of synthetics. Natural rubber, however, continues to maintain its competitive edge due mainly to the gain in properties such as high resilience, low hysteresis, low heat buildup, and excellent tack with mechanical properties achieved through the process of vulcanization [114-115]. The industry is said to be self-sufficient with a good technological base and is expected to compete successfully with synthetics because of the edge in properties mentioned above [116,117]. 

Synthetic rubbers (elastomers) are long-chain polymers with special chemical and physical as well as mechanical properties. These materials have chemical stability, high abrasion resistance, strength, and good dimensional stability. Many of these properties are imparted to the... 

Chapter 12 discusses the use of the various monomers obtained from a petroleum origin for producing commercial polymers. Not only does it cover the chemical reactions involved in the synthesis of these polymers, but it also presents their chemical, physical and mechanical properties. These properties are well related to the applicability of a polymer as a plastic, an elastomer, or as a fiber. 

The term s plastic, polymer, resin, elastomer, and reinforced plastic (RP) are some-what synonymous. However, polymer and resin usually denote the basic material. Whereas plastic pertains to polymers or resins containing additives, fillers, and/or reinforcements. Recognize that practically all materials worldwide contain some type of additive or ingredient. An elastomer is a rubberlike material (natural or synthetic). Reinforced plastics (also called composites although to be more accurate called plastic composites) are plastics with reinforcing additives, such as fibers and whiskers, added principally to increase the product s mechanical properties. 

Tests for indention under load are performed basically like the ASTM measure the hardness of other materials, such as metals and ceramics. There are at least four popular hardness scales in use. Shore A and Shore D is for soft to relatively hard plastics and elastomers. Barcol is used from the mid-range of Shore D to above it as well as RPs. Rockwell M is used for very hard plastics (Chapter 5, MECHANICAL PROPERTY, Hardness),... 

---