Hydrochloric acid reaction with calcium

A useful experiment that shows the effect of varying the surface area of a solid on reaction rate is based on the fact that hydrochloric acid reacts with calcium carbonate to produce the gas carbon dioxide. 

Calculate the number of moles of hydrogen gas that can be produced by reaction of 0.750 mol of hydrochloric acid, HCl, with calcium metal. 

About half of the hydrochloric acid produced annually in the United States (3.0 biUion pounds) is used for metal pickling. This process involves the removal of metal oxide layers from metal surfaces to prepare them for coating, (a) Write the overall and net ionic equations for the reaction between iron(lll) oxide, which represents the rust layer over iron, and HCl. Identify the Bronsted acid and base, (b) Hydrochloric acid is also used to remove scale (which is mostly CaC03) from water pipes. Hydrochloric acid reacts with calcium carbonate in two stages the first stage forms the bicarbonate ion, which then reacts further to form carbon dioxide. Write equations for these two stages and for the overall reaction. 

A word of caution at this point seems most desirable. In every case where a pure aldonic acid or its derivative has been heated with o-phenyl-enediamine and an excess of hydrochloric acid, only a single benzimidazole has been isolated. It is well known that aldonic acids are epimerized by heating them at temperatures above 100° with organic bases such as pyridine. The heating of an aldonic acid with o-phenylenediamine at 135-150° may also result in appreciable epimerization. Thus, Moore and Link20 reported that from the fusion of xylonic acid with o-phenylenediamine at 150°, in the absence of mineral acids, they could isolate the epimeric lyxo-benzimidazole. Barker, Farrar, and Gulland,21 in a more detailed study, proved conclusively that both D-ribo- and D-arabo-benzimidazoles were formed when the condensation of calcium D-ribonate with o-phenylenediamine was carried out in the presence of less than two molecular equivalents of hydrochloric acid, whereas with an excess of hydrochloric acid only the D-ribo-benzimidazole was obtained. It is important, therefore, in the condensation of o-phenylenediamine with an optically active acid at an elevated temperature that the reaction mixture always be kept on the acid side. 

A. How many moles of hydrochloric acid does it take to prepare 1.50 mol of calcium chloride by reaction with calcium carbonate ... 

Figure 5.2.3 shows the results of these methods and how the rate of a reaction between calcium carbonate and hydrochloric acid varies with time. The graphs have different shapes because one charts the change in formation of carbon dioxide, i.e. the products, and the other shows how the reaction changes with relation to the reactants, i.e. how fast the system loses mass as the calcium carbonate and hydrochloric acid react to form carbon dioxide. 

Eq. 10.34) is more rapid with hydrochloric acid than with sulfuric acid, and yields soluble products from both the calcium and phosphate. Thus, there is neither a need to heat the mixture to speed up the reaction, nor are there any crystal form problems requiring temperature stabilization. 

Insoluble gases are often formed by the breakdown of an xmstable doubledisplacement reaction product. For example, carbonates react with acids to form carbonic acid (H2CO3), an unstable substance that readily decomposes into water and carbon dioxide. Calcium carbonate reacts with hydrochloric acid to form calcium chloride and carbonic acid ... 

Use the apparatus detailed in Section 111,20. Dissolve 100 g. (123 ml.) of methyl n-butyl ketone (2-hexanone) (Section 111,152) in 750 ml. of ether and add 150 ml. of water. Introduce 69 g. of clean sodium in the form of wire (or small pieces) as rapidly as possible the reaction must be kept under control and, if necessary, the flask must be cooled in ice or in running water. When all the sodium has reacted, separate the ethereal layer, wash it with 25 ml. of dilute hydrochloric acid (1 1), then with water, dry with anhydrous potassium carbonate or with anhydrous calcium sulphate, and distil through a fractionating column. Collect the fraction of b.p. 136-138°. The yield of methyl n-butyl carbinol (2-hexanol) is 97 g. 

In a 1500 ml. round-bottomed flask, carrying a reflux condenser, place 100 g. of pure cydohexanol, 250 ml. of concentrated hydrochloric acid and 80 g. of anhydrous calcium chloride heat the mixture on a boiling water bath for 10 hours with occasional shaking (1). Some hydrogen chloride is evolved, consequently the preparation should be conducted in the fume cupboard. Separate the upper layer from the cold reaction product, wash it successively with saturated salt solution, saturated sodium bicarbonate solution, saturated salt solution, and dry the crude cycZohexyl chloride with excess of anhydrous calcium chloride for at least 24 hours. Distil from a 150 ml. Claisen flask with fractionating side arm, and collect the pure product at 141-5-142-5°. The yield is 90 g. 

Allyl Chloride. Comparatively poor yields are obtained by the zinc chloride - hydrochloric acid method, but the following procedure, which employs cuprous chloride as a catalyst, gives a yield of over 90 per cent. Place 100 ml. of allyl alcohol (Section 111,140), 150 ml. of concentrated hydrochloric acid and 2 g. of freshly prepared cuprous chloride (Section II,50,i one tenth scale) in a 750 ml. round-bottomed flask equipped with a reflux condenser. Cool the flask in ice and add 50 ml. of concen trated sulphuric acid dropwise through the condenser with frequent shaking of the flask. A little hydrogen chloride may be evolved towards the end of the reaction. Allow the turbid liquid to stand for 30 minutes in order to complete the separation of the allyl chloride. Remove the upper layer, wash it with twice its volume of water, and dry over anhydrous calcium chloride. Distil the allyl chloride passes over at 46-47°. 

Fit a 1500 ml. bolt-head flask with a reflux condenser and a thermometer. Place a solution of 125 g. of chloral hydrate in 225 ml. of warm water (50-60°) in the flask, add successively 77 g. of precipitated calcium carbonate, 1 ml. of amyl alcohol (to decrease the amount of frothing), and a solution of 5 g. of commercial sodium cyanide in 12 ml. of water. An exothermic reaction occurs. Heat the warm reaction mixture with a small flame so that it reaches 75° in about 10 minutes and then remove the flame. The temperature will continue to rise to 80-85° during 5-10 minutes and then falls at this point heat the mixture to boiling and reflux for 20 minutes. Cool the mixture in ice to 0-5°, acidify with 107-5 ml. of concentrated hydrochloric acid. Extract the acid with five 50 ml. portions of ether. Dry the combined ethereal extracts with 10 g. of anhydrous sodium or magnesium sulphate, remove the ether on a water bath, and distil the residue under reduced pressure using a Claiseii flask with fractionating side arm. Collect the dichloroacetic acid at 105-107°/26 mm. The yield is 85 g. 

---