Fed productivity

The method of precutting or postcutting to length has an effect on roll design. In most cases, sheet-fed products are more prone to flair and the minimum product... 

Typical experimental results are listed in Table V, Conversion of DAO, X, was defined based on the stoichiometry of the pyrolysis of DAO to allyl radicals and CO2 as x = (1/2) (moles of CO2 formed/moles of DAO fed). Product distribution was calculated on the basis of 100 moles of DAO converted. Fewer products were obtained than those in the reaction of diallyl in excess ethylene. Lower temperatures favored the formation of cyclopentene and 1-butene as compared to those of 1-pentene and butadiene, respectively ... 

Figure 3.8a shows the temperature-composition diagram for a minimum-boiling azeotrope that is sensitive to changes in pressure. This azeotrope can be separated using two columns operating at different pressures, as shown in Fig. 3.86. Feed with mole fraction of A Ufa)) of, say, 0.3 is fed to the high-pressure column. The bottom product from this high-pressure column is relatively pure B, whereas the overhead is an azeotrope with jcda = 0-8, jcdb = 0.2. This azeotrope is fed to the low-pressure column, which produces relatively pure A in the bottom and in the overhead an azeotrope with jcda = 0.6, jcdb = 0.4. This azeotrope is added to the feed of the high-pressure column.

In the 1970 s, heavy fuel came mainly from atmospheric distillation residue. Nowadays a very large proportion of this product is vacuum distilled and the distillate obtained is fed to conversion units such as catalytic cracking, visbreaking and cokers. These produce lighter products —gas and gasoline— but also very heavy components, that are viscous and have high contaminant levels, that are subsequently incorporated in the fuels. 

In recent years much more attention has been given to pipeline isolation, after instances in which the contents of export pipelines fed platform fires, adding significantly to damage and loss of life. Many export and in field pipelines are now fitted with emergency shutdown valves (ESDV) close to the production platform, to isolate the pipeline in the event of an emergency. 

Small amounts of propionitrile and bis(cyanoethyl) ether are formed as by-products. The hydrogen ions are formed from water at the anode and pass to the cathode through a membrane. The catholyte that is continuously recirculated in the cell consists of a mixture of acrylonitrile, water, and a tetraalkylammonium salt the anolyte is recirculated aqueous sulfuric acid. A quantity of catholyte is continuously removed for recovery of adiponitrile and unreacted acrylonitrile the latter is fed back to the catholyte with fresh acrylonitrile. Oxygen that is produced at the anodes is vented and water is added to the circulating anolyte to replace the water that is lost through electrolysis. The operating temperature of the cell is ca 50—60°C. Current densities are 0.25-1.5 A/cm (see Electrochemical processing). 

The urea solution stream is then fed to the vacuum concentrator unit which operates at 17.3 kPa (130 mm Hg abs) and produces 88.7 wt % urea. It then goes to either two-stage evaporators if prills are made, or a single-stage unit for granule production. 

In production, anhydrous formaldehyde is continuously fed to a reactor containing well-agitated inert solvent, especially a hydrocarbon, in which monomer is sparingly soluble. Initiator, especially amine, and chain-transfer agent are also fed to the reactor (5,16,17). The reaction is quite exothermic and polymerisation temperature is maintained below 75°C (typically near 40°C) by evaporation of the solvent. Polymer is not soluble in the solvent and precipitates early in the reaction. 

The enthalpy of the copolymerization of trioxane is such that bulk polymerization is feasible. For production, molten trioxane, initiator, and comonomer are fed to the reactor a chain-transfer agent is in eluded if desired. Polymerization proceeds in bulk with precipitation of polymer and the reactor must supply enough shearing to continually break up the polymer bed, reduce particle size, and provide good heat transfer. The mixing requirements for the bulk polymerization of trioxane have been reviewed (22). Raw copolymer is obtained as fine emmb or flake containing imbibed formaldehyde and trioxane which are substantially removed in subsequent treatments which may be combined with removal of unstable end groups. 

The bottoms from the solvent recovery (or a2eotropic dehydration column) are fed to the foremns column where acetic acid, some acryflc acid, and final traces of water are removed overhead. The overhead mixture is sent to an acetic acid purification column where a technical grade of acetic acid suitable for ester manufacture is recovered as a by-product. The bottoms from the acetic acid recovery column are recycled to the reflux to the foremns column. The bottoms from the foremns column are fed to the product column where the glacial acryflc acid of commerce is taken overhead. Bottoms from the product column are stripped to recover acryflc acid values and the high boilers are burned. The principal losses of acryflc acid in this process are to the aqueous raffinate and to the aqueous layer from the dehydration column and to dimeri2ation of acryflc acid to 3-acryloxypropionic acid. If necessary, the product column bottoms stripper may include provision for a short-contact-time cracker to crack this dimer back to acryflc acid (60). 

A schematic of a continuous bulk SAN polymerization process is shown in Figure 4 (90). The monomers are continuously fed into a screw reactor where copolymerization is carried out at 150°C to 73% conversion in 55 min. Heat of polymerization is removed through cooling of both the screw and the barrel walls. The polymeric melt is removed and fed to the devolatilizer to remove unreacted monomers under reduced pressure (4 kPa or 30 mm Hg) and high temperature (220°C). The final product is claimed to contain less than 0.7% volatiles. Two devolatilizers in series are found to yield a better quaUty product as well as better operational control (91,92). 

The alcoholysis reaction may be carried out either batchwise or continuously by treating the triglyceride with an excess of methanol for 30—60 min in a well-agitated reactor. The reactants are then allowed to settle and the glycerol [56-81-5] is recovered in methanol solution in the lower layer. The sodium methoxide and excess methanol are removed from the methyl ester, which then maybe fed directiy to the hydrogenolysis process. Alternatively, the ester may be distilled to remove unreacted material and other impurities, or fractionated into different cuts. Practionation of either the methyl ester or of the product following hydrogenolysis provides alcohols that have narrow carbon-chain distributions. 

The second experimental problem is that incorporation of a material such as loganin (34), or even an amino acid which seems cleady to be a precursor by some biogenetic hypothesis, does not necessarily prove it is a precursor. The material fed may so completely swamp the normal pathways in the plant that the utiliza tion of what was fed generates an aberrant path which nonetheless produces the same product. 

The two procedures primarily used for continuous nitration are the semicontinuous method developed by Bofors-Nobel Chematur of Sweden and the continuous method of Hercules Powder Co. in the United States. The latter process, which uses a multiple cascade system for nitration and a continuous wringing operation, increases safety, reduces the personnel involved, provides a substantial reduction in pollutants, and increases the uniformity of the product. The cellulose is automatically and continuously fed into the first of a series of pots at a controlled rate. It falls into the slurry of acid and nitrocellulose and is submerged immediately by a turbine-type agitator. The acid is deflvered to the pots from tanks at a rate controlled by appropriate instmmentation based on the desired acid to cellulose ratio. The slurry flows successively by gravity from the first to the last of the nitration vessels through under- and overflow weirs to ensure adequate retention time during nitration. The overflow from the last pot is fully nitrated cellulose. 

In order to maintain a definite contact area, soHd supports for the solvent membrane can be introduced (85). Those typically consist of hydrophobic polymeric films having pore sizes between 0.02 and 1 p.m. Figure 9c illustrates a hoUow fiber membrane where the feed solution flows around the fiber, the solvent—extractant phase is supported on the fiber wall, and the strip solution flows within the fiber. Supported membranes can also be used in conventional extraction where the supported phase is continuously fed and removed. This technique is known as dispersion-free solvent extraction (86,87). The level of research interest in membrane extraction is reflected by the fact that the 1990 International Solvent Extraction Conference (20) featured over 50 papers on this area, mainly as appHed to metals extraction. Pilot-scale studies of treatment of metal waste streams by Hquid membrane extraction have been reported (88). The developments in membrane technology have been reviewed (89). Despite the research interest and potential, membranes have yet to be appHed at an industrial production scale (90). 

---