Electrode intercalation

These equations can be solved for semi-infinite external diffusion, where both Red and Ox forms are in the solution outside the sphere (diffusion to a spherical or hemispherical hanging mercury electrode, metallic solid spherical electrode), or they may diffuse inside the sphere (amalgam formation at mercury electrode, intercalation of Li into particles, hydrogen absorption into spherical hydrogenabsorbing particles). 

Lithium-ion cells (Fig. 1.1) rely on reversible insertion (intercalation ) of lithium ions into the structures of cathode and anode active materials, respectively. When active material in an electrode intercalates lithium ions, it becomes electrochemically... 

Lithium batteries based on organic solvents are now made on a large scale for medical applications, back up power for computer memories, power for small electronic gadgets and the general consumer market Batteries based on four types of positive electrode (intercalation into Mn02, reduction of poly (carbon monofluoride), cupric oxide and silver chromate) are listed in Table 11.7 note that the exact solvent-electrolyte ts not specified because their selection is considered conlidential The exact composition may also vary from company to company. AH these batteries give performances markedly better than the traditional batteries (Table f 1.8). The better performance, however, is obtained... 

In such a battery, a carbon electrode that forms layers and allows intercalation of Li ions is combined with a positive electrode of a metal oxide that also intercalates the small Li ions into a layered structure (mainly LixC02, LixNi02, or LixMn204). These positive electrodes intercalate the lithium when discharged, i.e. the lithium-filled material characterizes the discharged state of the positive electrode, and the Li ions compensate for a corresponding reduction of the metal ions... 

TABLE 34.5 Key Requiiements for Positive-Electrode Intercalation Material (li O ) Used in Rechaigeable Lithium CeUs... 

Graphite reacts with alkali metals, for example potassium, to form compounds which are non-stoichiometric but which all have limiting compositions (for example K C) in these, the alkaU metal atoms are intercalated between the layers of carbon atoms. In the preparation of fluorine by electrolysis of a molten fluoride with graphite electrodes the solid compound (CF) polycarbon fluoride is formed, with fluorine on each carbon atom, causing puckering of the rings. 

Further improvements in anode performance have been achieved through the inclusion of certain metal salts in the electrolyte, and more recently by dkect incorporation into the anode (92,96,97). Good anode performance has been shown to depend on the formation of carbon—fluorine intercalation compounds at the electrode surface (98). These intercalation compounds resist further oxidation by fluorine to form (CF ), have good electrical conductivity, and are wet by the electrolyte. The presence of certain metals enhance the formation of the intercalation compounds. Lithium, aluminum, or nickel fluoride appear to be the best salts for this purpose (92,98). 

The most important rechargeable lithium batteries are those using a soHd positive electrode within which the lithium ion is capable of intercalating. These intercalation, or insertion, electrodes function by allowing the interstitial introduction of the LE ion into a host lattice (16,17). The general reaction can be represented by the equation ... 

In the lithium-ion approach, the metallic lithium anode is replaced by a lithium intercalation material. Then, tw O intercalation compound hosts, with high reversibility, are used as electrodes. The structures of the two electrode hosts are not significantly altered as the cell is cycled. Therefore the surface area of both elecftodes can be kept small and constant. In a practical cell, the surface area of the powders used to make up the elecftodes is nomrally in the 1 m /g range and does not increase with cycle number [4]. This means the safety problems of AA and larger size cells can be solved. 

Reaction overpotential. Both overpotentials mentioned above are normally of higher importance than the reaction overpotential. It may happen sometimes, however, that other phenomena, which occur in the electrolyte or during electrode processes, such as adsorption and desorption, are the speed-limiting factors. Crystallization overpotential. This exists as a result of the inhibited intercalation of metal ions into their lattice. This process is of fundamental importance when secondary batteries are charged, especially during metal deposition on the negative side. 

Carbon materials which have the closest-packed hexagonal structures are used as the negative electrode for lithium-ion batteries carbon atoms on the (0 0 2) plane are linked by conjugated bonds, and these planes (graphite planes) are layered. The layer interdistance is more than 3.35 A and lithium ions can be intercalated and dein-tercalated. As the potential of carbon materials with intercalated lithium ions is low,... 

In redox flow batteries such as Zn/Cl2 and Zn/Br2, carbon plays a major role in the positive electrode where reactions involving Cl2 and Br2 occur. In these types of batteries, graphite is used as the bipolar separator, and a thin layer of high-surface-area carbon serves as an electrocatalyst. Two potential problems with carbon in redox flow batteries are (i) slow oxidation of carbon and (ii) intercalation of halogen molecules, particularly Br2 in graphite electrodes. The reversible redox potentials for the Cl2 and Br2 reactions [Eq. (8) and... 

Whereas the electrochemical decomposition of propylene carbonate (PC) on graphite electrodes at potentials between 1 and 0.8 V vs. Li/Li was already reported in 1970 [140], it took about four years to find out that this reaction is accompanied by a partially reversible electrochemical intercalation of solvated lithium ions, Li (solv)y, into the graphite host [64], In general, the intercalation of Li (and other alkali-metal) ions from electrolytes with organic donor solvents into fairly crystalline graphitic carbons quite often yields solvated (ternary) lithiated graphites, Li r(solv)yC 1 (Fig. 8) [7,24,26,65,66,141-146],... 

The chemical composition of the SEI formed on carbonaceous anodes is, in general, similar to that formed on metallic lithium or inert electrodes. However some differences are expected as a result of the variety of chemical compositions and morphologies of carbon surfaces, each of which can affect the i() value for the various reduction reactions differently. Another factor, when dealing with graphite, is solvent co-intercalation. Assuming Li2C03 to be a major SEI building material, the thickness of the SEI was estimated to be about 45 A [711. 

---