Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Electrochemistry cells

Figures 12.1 and 12.2 show that the spectroelectrochemical cell is basically a thin-layer electrochemistry cell (TLE) with a solution gap of 25 pm [Hubbard, 1973]. The metal working electrode may be polycrystalline or a single crystal. Emptying the gap out of the adsorbate molecules due to molecules oxidation, and refilling via molecular... Figures 12.1 and 12.2 show that the spectroelectrochemical cell is basically a thin-layer electrochemistry cell (TLE) with a solution gap of 25 pm [Hubbard, 1973]. The metal working electrode may be polycrystalline or a single crystal. Emptying the gap out of the adsorbate molecules due to molecules oxidation, and refilling via molecular...
As shown in Table 9.1, the typical timescale for the electrochemistry ( Cell Charging Time ) is on the order of 10-5 s. As a result, it is often that this transient is ignored in cell performance calculations, and the quasi-steady Butler-Volmer relationship is used alone (Qi et al., 2005). An example model for this particular type of dynamic cell behavior is given in Section 9.5. [Pg.283]

Clay-modified electrodes with ruthenium purple Enzymic treatment with Cucumis sativus tissue which is a rich source of ascorbate oxidase Based on the quantitative electrolysis of AA A four-channel multipotentiostat for simultaneous measurements with microelectrode arrays. To reduce the complexity of electrochemistry cell, only one reference, and one auxiliary electrode are used Electrocatalytic determination of AA using tetraaza macrocycle-modified electrodes Neutralization of AA in ammonia leading to a change in conductivity... [Pg.321]

One of the main uses of these wet cells is to investigate surface electrochemistry [94, 95]. In these experiments, a single-crystal surface is prepared by UFIV teclmiqiies and then transferred into an electrochemical cell. An electrochemical reaction is then run and characterized using cyclic voltaimnetry, with the sample itself being one of the electrodes. In order to be sure that the electrochemical measurements all involved the same crystal face, for some experiments a single-crystal cube was actually oriented and polished on all six sides Following surface modification by electrochemistry, the sample is returned to UFIV for... [Pg.314]

A second source of standard free energies comes from the measurement of the electromotive force of a galvanic cell. Electrochemistry is the subject of other articles (A2.4 and B1.28). so only the basics of a reversible chemical cell will be presented here. For example, consider the cell conventionally written as... [Pg.365]

The combination of electrochemistry and photochemistry is a fonn of dual-activation process. Evidence for a photochemical effect in addition to an electrochemical one is nonnally seen m the fonn of photocurrent, which is extra current that flows in the presence of light [, 89 and 90]. In photoelectrochemistry, light is absorbed into the electrode (typically a semiconductor) and this can induce changes in the electrode s conduction properties, thus altering its electrochemical activity. Alternatively, the light is absorbed in solution by electroactive molecules or their reduced/oxidized products inducing photochemical reactions or modifications of the electrode reaction. In the latter case electrochemical cells (RDE or chaimel-flow cells) are constmcted to allow irradiation of the electrode area with UV/VIS light to excite species involved in electrochemical processes and thus promote fiirther reactions. [Pg.1945]

Another troublesome aspect of the reactivity ratios is the fact that they must be determined and reported as a pair. It would clearly simplify things if it were possible to specify one or two general parameters for each monomer which would correctly represent its contribution to all reactivity ratios. Combined with the analogous parameters for its comonomer, the values rj and t2 could then be evaluated. This situation parallels the standard potential of electrochemical cells which we are able to describe as the sum of potential contributions from each of the electrodes that comprise the cell. With x possible electrodes, there are x(x - l)/2 possible electrode combinations. If x = 50, there are 1225 possible cells, but these can be described by only 50 electrode potentials. A dramatic data reduction is accomplished by this device. Precisely the same proliferation of combinations exists for monomer combinations. It would simplify things if a method were available for data reduction such as that used in electrochemistry. [Pg.444]

Electrochemical systems are found in a number of industrial processes. In addition to the subsequent discussions of electrosynthesis, electrochemical techniques are used to measure transport and kinetic properties of systems (see Electroanalyticaltechniques) to provide energy (see Batteries Euel cells) and to produce materials (see Electroplating). Electrochemistry can also play a destmctive role (see Corrosion and corrosion control). The fundamentals necessary to analyze most electrochemical systems have been presented. More details of the fundamentals of electrochemistry are contained in the general references. [Pg.67]

Because silver, gold and copper electrodes are easily activated for SERS by roughening by use of reduction-oxidation cycles, SERS has been widely applied in electrochemistry to monitor the adsorption, orientation, and reactions of molecules at those electrodes in-situ. Special cells for SERS spectroelectrochemistry have been manufactured from chemically resistant materials and with a working electrode accessible to the laser radiation. The versatility of such a cell has been demonstrated in electrochemical reactions of corrosive, moisture-sensitive materials such as oxyhalide electrolytes [4.299]. [Pg.262]

In contrast to many other surface analytical techniques, like e. g. scanning electron microscopy, AFM does not require vacuum. Therefore, it can be operated under ambient conditions which enables direct observation of processes at solid-gas and solid-liquid interfaces. The latter can be accomplished by means of a liquid cell which is schematically shown in Fig. 5.6. The cell is formed by the sample at the bottom, a glass cover - holding the cantilever - at the top, and a silicone o-ring seal between. Studies with such a liquid cell can also be performed under potential control which opens up valuable opportunities for electrochemistry [5.11, 5.12]. Moreover, imaging under liquids opens up the possibility to protect sensitive surfaces by in-situ preparation and imaging under an inert fluid [5.13]. [Pg.280]

Electrochemistry is the study of the interconversion of electrical and chemical energy. This conversion takes place in an electrochemical cell that may be a(n)—... [Pg.481]

J. Burbank, A.C. Simon, E. Willihnganz, The lead acid cell, in Advances in Electrochemistry and Electrochemical Engineering, Vol. 8, John Wiley, New York, 1971, p. 170. [Pg.174]

The implications of Equation (4.30) for solid state electrochemistry and electrochemical promotion in particular can hardly be overemphasized It shows that solid electrolyte cells are both work function probes and work function controllers for their gas-exposed electrode surfaces. [Pg.140]

Work function, a quantity of great importance in surface science and catalysis, plays a key role in solid state electrochemistry and in electrochemical promotion. As will be shown in Chapter 7 the work function of the gas-exposed surface of an electrode in a solid electrolyte cell can be used to define an absolute potential scale in solid state electrochemistry. [Pg.205]

It must be emphasized that Equations (5.24) and (5.25) stem from the definitions of Fermi level, work function and Volta potential and are generally valid for any electrochemical cell, solid state or aqueous. We can now compare these equations with the corresponding experimental equations (5.18) and (5.19) found to hold, under rather broad temperature, gaseous composition and overpotential conditions (Figs. 5.8 to 5.16), in solid state electrochemistry ... [Pg.216]

Equations (5.18) and (5.19), particularly the latter, have only recently been reported and are quite important for solid state electrochemistry. Some of then-consequences are not so obvious. For example consider a solid electrolyte cell Pt/YSZ/Ag with both electrodes exposed to the same P02, so that Uwr = 0. Equation (5.19) implies that, although the work functions of a clean Pt and a clean Ag surface are quite different (roughly 5.3 eV vs 4.7 eV respectively) ion backspillover from the solid electrolyte onto the gas exposed electrode surfaces will take place in such a way as to equalize the work functions on the two surfaces. This was already shown in Figs. 5.14 and 5.15. [Pg.225]

What is the practical usefulness of the soe scale of solid state electrochemistry As in aqueous electrochemistry, it is limited but not trivial. When a potential Uwr of, e.g. -300 mV is measured in an YSZ solid state cell at 673 K vs a reference electrode at p02=l atm, the implication is that the work function of the reference electrode is 5.14 eV and that of the working electrode 4.84 eV regardless of the material of the two electrodes. [Pg.354]

In summary, the creation via ion spillover of an effective electrochemical double layer on the gas exposed electrode surfaces in solid electrolyte cells, which is similar to the double layer of emersed electrodes in aqueous electrochemistry, and the concomitant experimentally confirmed equation... [Pg.355]

As in aqueous electrochemistry it appears that application of a potential between the two terminal (Au) electrodes leads to charge separation on the Pt film so that half of it is charged positively and half negatively8 thus establishing two individual galvanic cells. The Pt film becomes a bipolar electrode and half of it is polarized anodically while the other half is polarized cathodically. The fact that p is smaller (roughly half) than that obtained upon anodic polarization in a classical electrochemical promotion experiment can be then easily explained. [Pg.523]

Why Do We Need to Know This Material The topics described in this chapter may one day unlock a virtually inexhaustible supply of clean energy supplied daily by the Sun. The key is electrochemistry, the study of the interaction of electricity and chemical reactions. The transfer of electrons from one species to another is one of the fundamental processes underlying life, photosynthesis, fuel cells, and the refining of metals. An understanding of how electrons are transferred helps us to design ways to use chemical reactions to generate electricity and to use electricity to bring about chemical reactions. Electrochemical measurements also allow us to determine the values of thermodynamic quantities. [Pg.603]

Electrochemistry is one of the main methods used to determine equilibrium constants that are either very large or very small. To measure the equilibrium constant for the reaction of Fe(CN) 4 with Na2Cr207, the following cell was built ... [Pg.647]

Bockris, J. O M., and Srinivasan, S. K. (1969). Fuel Cells—Tlieir Electrochemistry , McGraw Hill. [Pg.220]

Electrochemistry is the basis of many important and modem applications and scientific developments such as nanoscale machining (fabrication of miniature devices with three dimensional control in the nanometer scale), electrochemistry at the atomic scale, scanning tunneling microscopy, transformation of energy in biological cells, selective electrodes for the determination of ions, and new kinds of electrochemical cells, batteries and fuel cells. [Pg.399]


See other pages where Electrochemistry cells is mentioned: [Pg.287]    [Pg.109]    [Pg.13]    [Pg.33]    [Pg.757]    [Pg.117]    [Pg.287]    [Pg.109]    [Pg.13]    [Pg.33]    [Pg.757]    [Pg.117]    [Pg.1948]    [Pg.127]    [Pg.554]    [Pg.2411]    [Pg.134]    [Pg.218]    [Pg.499]    [Pg.539]    [Pg.525]    [Pg.125]    [Pg.44]    [Pg.395]    [Pg.125]    [Pg.340]    [Pg.356]    [Pg.552]    [Pg.948]    [Pg.1031]    [Pg.400]   
See also in sourсe #XX -- [ Pg.112 , Pg.113 , Pg.117 ]




SEARCH



Concentration cells, electrochemistry

Electrochemistry Cell potential Electrolysis

Electrochemistry Downs cell

Electrochemistry Membranes cells

Electrochemistry Mercury cathode cells

Electrochemistry and thermodynamics of fuel cells

Electrochemistry at the cell membrane-solution interface

Electrochemistry cell diagrams

Electrochemistry cell potential

Electrochemistry cell potential, electrical work

Electrochemistry cell voltage

Electrochemistry electrochemical cells

Electrochemistry electrolytic cells

Electrochemistry fuel cells

Electrochemistry galvanic cells

Electrochemistry half-cell

Electrochemistry half-cell reactions

Electrochemistry half-cell voltages

Electrochemistry in and at Single Biological Cells

Electrochemistry in electrochemical cells of sub-microlitre volume

Electrochemistry of Fuel Cells

Electrochemistry of copper dithiocarbamate complexes in a conventional electrochemical cell

Electrochemistry principles electrochemical cell

Electrochemistry standard cell potential

Electrochemistry standard cell voltage

Electrochemistry voltaic cells

Electrochemistry, Batteries, and Fuel Cells

Electrochemistry, batteries fuel cells

Electrolyte Fuel Cells, Modern Aspects of Electrochemistry

Fuel cell technologies electrochemistry

Fuel cells reaction electrochemistry

PEM Fuel Cell Electrochemistry

Polymer electrolyte membrane fuel cells electrochemistry

Preparative electrochemistry, cells

© 2024 chempedia.info