Mechanical properties ductility

A table of the properties of a variety of perfluorocyclobutane thermoplastic polymers can be found in the literature (13,17). As an example of the types of properties that can be achieved with this polymer chemistry. Table I lists the properties of the thermoplastic homopolymer prepared from 4,4 -bis(trifluorovinyloxy)biphenyl (monomer CAS 134130-19-1, polymer CAS 134174-05-3) (see Figure 5). This particular thermoplastic has been studied more than any other thermoplastic because of its combination of properties, including a relatively higher Tg and good ductile mechanical properties. 

Table 13 is a representative Hst of nickel and cobalt-base eutectics for which mechanical properties data are available. In most eutectics the matrix phase is ductile and the reinforcement is britde or semibritde, but this is not invariably so. The strongest of the aHoys Hsted in Table 13 exhibit ultimate tensile strengths of 1300—1550 MPa. Appreciable ductiHty can be attained in many fibrous eutectics even when the fibers themselves are quite britde. However, some lamellar eutectics, notably y/y —5, reveal Htde plastic deformation prior to fracture. 

Lead—tin (1.8—2.5 wt %) is used both as a cable sheathing ahoy (BS 801 ahoy A and DIN 17640) and as a battery connector ahoy ia sealed lead—calcium—tin batteries (15). Tia is generahy added to lead—arsenic cable ahoys ia smah amounts. The arsenic ahoys have excehent creep resistance and mechanical properties, but are unstable and lose arsenic readily by oxidation. The addition of smah amounts of tin (0.10—0.20 wt %) eliminates arsenic loss. Lead ahoys having 0.4 wt % tin and 0.15 % cadmium, which are used for cable sheathing, do not age harden, show excehent corrosion and creep resistance, and are very ductile. 

Copper and nickel can be alloyed with zinc to form nickel silvers. Nickel silvers are ductile, easily formed and machined, have good corrosion resistance, can be worked to provide a range of mechanical properties, and have an attractive white color. These alloys are used for ornamental purposes, as sHverplated and uncoated tableware and flatware in the electrical iadustry as contacts, connections, and springs and as many formed and machined parts (see Electrical connectors). 

The mechanical properties of LDPE fall somewhere between rigid polymers such as polystyrene and limp or soft polymers such as polyvinyls. LDPE exhibits good toughness and pHabiUty over a moderately wide temperature range. It is a viscoelastic material that displays non-Newtonian flow behavior, and the polymer is ductile at temperatures well below 0°C. Table 1 fists typical properties. 

Properties. Pure thorium metal is a dense, bright silvery metal having a very high melting point. The metal exists in two allotropic modifications. Thorium is a reactive, soft, and ductile metal which tarnishes slowly on exposure to air (12). Having poor mechanical properties, the metal has no direct stmctural appHcations. A survey of the physical properties of thorium is summarized in Table 1. Thorium metal is diamagnetic at room temperature, but becomes superconducting below 1.3—1.4 K. 

Mechanical history, heat, and impurities gready affect the mechanical properties. Pure zinc is ductile at room temperature and does not have a definite yield point as do most stmctural metals. Rather, it creeps under sufficient constant load. The impurities of commercial zinc and alloying metals are carefully controlled to achieve the desired mechanical properties. 

Alpha—beta aluminum alloys respond to heat treatment with a general improvement of mechanical properties. Heat treatment is accompHshed by heating to 815—870°C, quenching in water, and reannealing at 370—535°C, depending on the size and section of the casting. Different combinations of strength, hardness, and ductility can be obtained. Some nickel in aluminum bronze is in soHd solution with the matrix and helps refine the precipitate, and a smaller amount is in the K-intermetaUic compound. 

The hexagonal-close-packed (hep) metals generally exhibit mechanical properties intermediate between those of the fee and bcc metals. For example Zn encounters a ductile-to-brittle transition whereas Zr and pure Ti do not. The latter and their alloys with a hep structure remain reasonably ductile at low temperatures and have been used for many applications where weight reduction and reduced heat leakage through the material have been important. However, small impurities of O, N, H, and C can have a detrimental effect on the low temperature ductihty properties of Ti and its alloys. 

Alloys of antimony, tin, and arsenic offer hmited improvement in mechanical properties, but the usefulness of lead is limited primarily because of its poor structural qualities. It has a low melting point and a high coefficient of expansion, and it is a veiy ductile material that will creep under a tensile stress as low as 1 MPa (145 IbFin"). 

The most important displacive transformation is the one that happens in carbon steels. If you take a piece of 0.8% carbon steel "off the shelf" and measure its mechanical properties you will find, roughly, the values of hardness, tensile strength and ductility given in Table 8.1. But if you test a piece that has been heated to red heat and then quenched into cold water, you will find a dramatic increase in hardness (4 times or more), and a big decrease in ductility (it is practically zero) (Table 8.1). 

Figure 11.7 shows how the mechanical properties of normalised carbon steels change with carbon content. Both the yield strength and tensile strength increase linearly with carbon content. This is what we would expect the FejC acts as a strengthening phase, and the proportion of FojC in the steel is linear in carbon concentration (Fig. 11.6a). The ductility, on the other hand, falls rapidly as the carbon content goes up (Fig. 11.7) because the a-FejC interfaces in pearlite are good at nucleating cracks.

The cast irons do not possess ductility. They cannot be pressed or forged even while heated however, their machining properties are considered good. Typical mechanical properties of various types of cast iron are given in Table 3.1. 

The outstanding properties of copper-base materials are high electrical and thermal conductivity, good durabihty in mildly corrosive chemical environments and excellent ductility for forming complex shapes. As a relatively weak material, copper is often alloyed with zinc (brasses), tin (bronzes), aluminum and nickel to improve its mechanical properties and corrosion resistance. 

Hydrogen effect on the mechanical properties results in markedly enhanced ductility and lowered flow stress of the alloys therefore they become workable at much lower temperatures. 

Hydrogen-induced cracking (HlC) is most commonly encountered in steels but other metals are susceptible, as shown in Table 53.3. The presence of hydrogen atoms in a metal degrades some of its mechanical properties, especially its ductility, leading in some cases to embrittlement. 

The mechanical properties including strength, ductility and creep resistance can be affected below these temperature. 

Cast irons are iron with high levels of carbon. Heat treatments and alloying element additions produce gray cast iron, malleable iron, ductile iron, spheroidal cast iron and other grades. The mechanical properties vary significantly. Nickel-containing cast irons have improved hardness and corrosion resistance. Copper or molybdenum additions improve strength. 

---