Intrinsic detector

Depending on the nature of the semiconductor material, photoelectric detectors can be classified as intrinsic or extrinsic detectors. Intrinsic photoelectric detectors are pure semiconductors, whereas in extrinsic photoelectric detectors some impurities are added to the semiconductor during the fabrication process. Energy diagrams showing the processes activated by photo-excitation in these two kinds of photoelectric detectors are shown in Figures 3.11 (a) and 3.11(b) for intrinsic and extrinsic detectors, respectively. 

Another recent improvement in detectors is an online viscometery detector. Using the pressure drop across a small capillary and the output of an in-series concentration detector, intrinsic viscosities can be calculated as a fimction of elution volume. These measurements allow viscosity-average molecular weights to be calculated for each elution volume and the construction of a molecular weight distribution. This detector also may be used to characterize branching. 

Germanium metal is also used in specially prepared Ge single crystals for y-ray detectors (54). Both the older hthium-drifted detectors and the newer intrinsic detectors, which do not have to be stored in hquid nitrogen, do an exceUent job of spectral analysis of y-radiation and are important analytical tools. Even more sensitive Ge detectors have been made using isotopicahy enriched Ge crystals. Most of these have been made from enriched Ge and have been used in neutrino studies (55—57). 

Detectors aie all intrinsic unless otherwise noted. See Fig. 1. Visible bandwidth near infrared = 0.700-1.00 fim. 

Fig. 1. Photoexcitation modes iu a semiconductor having band gap energy, E, and impurity states, E. The photon energy must be sufficient to release an electron (° ) iato the conduction band (CB) or a hole (o) iato the valence band (VB) (a) an intrinsic detector (b) and (c) extrinsic donor and acceptor...

Ideal Performance and Cooling Requirements. Eree carriers can be excited by the thermal motion of the crystal lattice (phonons) as well as by photon absorption. These thermally excited carriers determine the magnitude of the dark current,/ and constitute a source of noise that defines the limit of the minimum radiation flux that can be detected. The dark carrier concentration is temperature dependent and decreases exponentially with reciprocal temperature at a rate that is determined by the magnitude of or E for intrinsic or extrinsic material, respectively. Therefore, usually it is necessary to operate infrared photon detectors at reduced temperatures to achieve high sensitivity. The smaller the value of E or E, the lower the temperature must be. 

Fig. 9. Spectral sensitivity of detectors where the detector temperatures in K are in parentheses, and the dashed line represents the theoretical limit at 300 K for a 180° field of view, (a) Detectors from near uv to short wavelength infrared (b) lead salt family of detectors and platinum siUcide (c) detectors used for detection in the mid- and long wavelength infrared. The Hg CdTe, InSb, and PbSnTe operate intrinsically, the doped siUcon is photoconductive, and the GaAs/AlGaAs is a stmctured supedattice and (d) extrinsic germanium detectors showing the six most popular dopants.

Synthetic, nonionic polymers generally elute with little or no adsorption on TSK-PW columns. Characterization of these polymers has been demonstrated successfully using four types of on-line detectors. These include differential refractive index (DRI), differential viscometry (DV), FALLS, and MALLS detection (4-8). Absolute molecular weight, root mean square (RMS) radius of gyration, conformational coefficients, and intrinsic viscosity distributions have... 

To use universal calibration, intrinsic viscosity must be measured. An online, DV detector can measure specific viscosity, 7j,p, which is related to intrinsic viscosity by the expression... 

The most widely used molecular weight characterization method has been GPC, which separates compounds based on hydrodynamic volume. State-of-the-art GPC instruments are equipped with a concentration detector (e.g., differential refractometer, UV, and/or IR) in combination with viscosity or light scattering. A viscosity detector provides in-line solution viscosity data at each elution volume, which in combination with a concentration measurement can be converted to specific viscosity. Since the polymer concentration at each elution volume is quite dilute, the specific viscosity is considered a reasonable approximation for the dilute solution s intrinsic viscosity. The plot of log[r]]M versus elution volume (where [) ] is the intrinsic viscosity) provides a universal calibration curve from which absolute molecular weights of a variety of polymers can be obtained. Unfortunately, many reported analyses for phenolic oligomers and resins are simply based on polystyrene standards and only provide relative molecular weights instead of absolute numbers. 

Dimethylphenol lb 149 Dimelhylphenols lb 148,149 N,N-Dimethyl-p-toluidine lb 268 Dimethyl sulfoxide as intrinsic detector... 

Dimethoxytetrahydrofuran 265 Dimethyl sulfoxide, intrinsic detector 88 4-Dimethylamino benzaldehyde 265 4-Dimethylamino cinnamaldehyde 269... 

Figure 12 were superimposable on those for detector 2. Therefore, when the plot shown in Figure 14 is linear over the range of compositions involved in the sample, then (according to equations (1-4) ) the composition of the sample is the same at each retention volume. If the variation with retention volume is negligible the copolymer can then possibly be treated as is a homopolymer in GPC interpretation. In particular, intrinsic viscosity measurements could then lead to estimates of molecular weight via the universal calibration curve. 

In addition to the surface/interface selectivity, IR-Visible SFG spectroscopy provides a number of attractive features since it is a coherent process (i) Detection efficiency is very high because the angle of emission of SFG light is strictly determined by the momentum conservation of the two incident beams, together with the fact that SFG can be detected by a photomultiplier (PMT) or CCD, which are the most efficient light detectors, because the SFG beam is in the visible region, (ii) The polarization feature that NLO intrinsically provides enables us to obtain information about a conformational and lateral order of adsorbed molecules on a flat surface, which cannot be obtained by traditional vibrational spectroscopy [29-32]. (iii) A pump and SFG probe measurement can be used for an ultra-fast dynamics study with a time-resolution determined by the incident laser pulses [33-37]. (iv) As a photon-in/photon-out method, SFG is applicable to essentially any system as long as one side of the interface is optically transparent. 

---