Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Design engineering analysis

CAD software provides as an aid to represent the design, engineering analysis and also animation. One of the powerful CAD software that is used in designing the prototype in the project is IRONCAD which it models the parts and assemblies precisely. This interactive 3D graphic can also view various angles of model simply by specifying necessary dimension, orientation and position and enhance the designer s work. [Pg.736]

Careflil material selection is required to prevent brittle failure of tanks at low temperatures. In addition, for tanks where the service temperatures are reduced, it is essential that an engineering analysis be performed to ensure that the tanks are not subject to brittle failure at the house temperature. The tank and vessel codes usually specify allowable materials based on design temperature. Further information about selection of metals for low temperature is available (8). [Pg.318]

This approach attempts to permit the designer to evaluate and optimize alternatives quickly, using shortcut hand calculations. However, if it is to be adopted by practicing design engineers it must be complemented by software for at least the analysis, evaluation, and optimization stages. [Pg.82]

General Considerations Most pressure vessels for the chemical-process industry will continue to be designed and built to the rules of Sec. T11, Division 1. While the rules of Sec. T11, Division 2, will frequently provide thinner elements, the cost of the engineering analysis, stress analysis and higher-quality construction, material control, and inspection required by these rules frequently exceeds the savings from the use of thinner walls. [Pg.1026]

Equipment Selection Ideally, selection of equipment to produce a gas-in-hquid dispersion should be made on the basis of a complete economic analysis. The design engineer and especially the pilot-plant engineer seldom have sufficient information or time to do... [Pg.1422]

The book does not focus on occupational safety and health issues, although improved process safety can benefit these areas. Detailed engineering designs are outside the scope of this work. This book intends to identify issues and concerns in batch reaction systems and provide potential solutions to address these concerns. This should be of value to process design engineers, operators, maintenance personnel, as well as members of process hazards analysis teams. While this book offers potential solutions to specific issues/concerns, ultimately the user needs to make the case for the solutions that provide a balance between risk... [Pg.1]

Lipson, C. and Sheth, N. J. 1973 Statistical Design and Analysis of Engineering Experiments. NY McGraw-Hill. [Pg.388]

The standard requires the supplier to have the appropriate resources and equipment (when specified in the contract) to utilize computer-aided product design, engineering, and analysis that is compatible with the customer s and subcontractor systems. It is also required that the supplier be able to use numerical design and drawing data, by computer-aided methods for the manufacture of production tooling and prototypes. [Pg.202]

The term design-analysis is used to emphasize the essential, but not dominant, role of analysis in the overall structural design process. Analysis plays no role whatsoever in dress design (with the possible exception of the now-classical analysis of a strapless evening gown). However, engineering design of a structure must involve analysis in the form of mechanistic relationships. Those mechanistic relationships must be used to quantitatively determine how to create the structural capabilities and then to match them to the structural requirements. The dis-... [Pg.386]

Suppressive Shield Structural Design and Analysis Handbook, U.S. /Army Corps of Engineers, Huntsville, Div. No. HNDM-1110-1-2, 1977. [Pg.540]

Although it is not the intent of this chapter to delve into pipe stress and vibration analysis, a few alerting comments appear to he in order. From this, the design engineer should he ahle to seek the proper qualified technical help to analyze the stresses associated with the piping layout. [Pg.610]

Not all product components are subjected to a load in fact most are not subjected to loads requiring an engineering analysis via engineering equations, etc. Experience in the material behavior on similar products and/or similar performance requirements are all that is needed. In these products designers become involved in their processing features that will prevent or reduce internal stresses, with elements that will lead to consistent and economical production, with appearance and dimensional control, etc. [Pg.20]

Sophisticated design engineers unfamiliar with plastics behavior will be able to apply the information contained in this and other chapters to applicable sophisticated equations that involve such analysis as multiple and complex stress concentrations. The various machine-design texts and mechanical engineering handbooks listed in the Appendix A PLASTICS TOOLBOX and REF-... [Pg.140]

There are many books that address experimental design and present factorial experimental design in detail (for example Design and Analysis of Experiments by Montgomery (1997) or Design of Experiments by Anderson and McLean (1974)). As engineers, we are faced quite often with the need to design a set of preliminary experiments for a process that very little or essentially no information is available. [Pg.185]

Aungier, R. H. (1999) Centrifugal Compressors A Strategy for Aerodynamic Design and Analysis (American Society of Mechanical Engineers). [Pg.486]

The codes and standards are drawn up by committees of engineers experienced in vessel design and manufacturing techniques, and are a blend of theory, experiment and experience. They are periodically reviewed, and revisions issued to keep abreast of developments in design, stress analysis, fabrication and testing. The latest version of the appropriate national code or standard should always be consulted before undertaking the design of any pressure vessel. [Pg.796]

Y. S. Tang. Ph.D has more than 35 years of experience in the field of thermal and fluid flow. His research interests have covered aspects of thermal hydraulics that are related to conventional and nonconventional power generation systems, with an emphasis on nuclear reactor design and analysis that focuses on liquld-meta -cooled reactors. Dr. Tang is co-author of Radioactive Waste Management published by Taylor 8 Francis, and Thermal Analysis of Liquid Metal Fast Breeder Reactors, He received a B5. from National Central University In China and an MS. in mechanical engineering from the University of Wisconsin. He earned his Ph.D. [Pg.572]

The analysis of two-phase tubular contactors and pipelines is complicated because of the variety of configurations that the two-phase mixture may assume in these systems. The design engineer must have knowledge of the flow pattern that results from a given set of operating conditions if the in situ quantities such as pressure drop, holdup of each phase, phase Reynolds numbers, and interfacial area are to be determined. These in situ quantities must be known if the rate of heat transfer is to be predicted. [Pg.14]


See other pages where Design engineering analysis is mentioned: [Pg.231]    [Pg.192]    [Pg.320]    [Pg.231]    [Pg.192]    [Pg.320]    [Pg.287]    [Pg.71]    [Pg.84]    [Pg.85]    [Pg.523]    [Pg.803]    [Pg.439]    [Pg.29]    [Pg.153]    [Pg.388]    [Pg.396]    [Pg.280]    [Pg.474]    [Pg.25]    [Pg.1115]    [Pg.515]    [Pg.33]    [Pg.641]    [Pg.377]    [Pg.604]    [Pg.30]    [Pg.59]    [Pg.253]    [Pg.229]    [Pg.67]   


SEARCH



Design engineers

Designer analysis

Engineering analysis

Engineering design

© 2024 chempedia.info