Deactivation deposition

Agrawal (1980) computed the deposit concentration in the microspheres as a function of position in the pellet and time. Initially, the deposit concentrates in the microspheres near the outer region of the pellet. With the outer region deactivated, deposit formation progresses inward because of access to the inner microspheres through the unobstructed macropores. The profiles in the microspheres are more or less uniform because of the low Thiele modulus. In the case of the unimodal catalyst without macropores, the buildup of deposit in the outer region of the pellet would seal the outer pores and prevent access to internal sites. 

Consequently, we fully agree with Tatterson et al [33] who conclude that the ability of the FCC catalyst to rapidly deactivate deposited metals will be an important factor in resid cracking. 

In LCVD, activation (formation of the reactive species) and deactivation (deposition of materials) occur in the same gas phase because the power input is directly applied to monomer gases and the material formation occurs mainly in the same gas phase. 

Industrial C3 stream has been carried out for over 30 days without a rapid drop in activity [11], and It would seem that the effect and possiblly the nature of the foulant produced from vinyl acetylene is different from the other acetylenes. The conjugated nature of the vinyl acetylene molecule would make it particularly susceptible to Diels Alder type condensations leading to condensed aromatics and coke [36). Whether the deactivating deposits are significantly different requires further analysis, and such tests are currently in progress. 

This was a Hquid-phase process which used what was described as siUceous zeoUtic catalysts. Hydrogen was not required in the process. Reactor pressure was 4.5 MPa and WHSV of 0.68 kg oil/h kg catalyst. The initial reactor temperature was 127°C and was raised as the catalyst deactivated to maintain toluene conversion. The catalyst was regenerated after the temperature reached about 315°C. Regeneration consisted of conventional controlled burning of the coke deposit. The catalyst life was reported to be at least 1.5 yr. 

Hydrogenation of the oxides of carbon to methane according to the above reactions is sometimes referred to as the Sabatier reactions. Because of the high exothermicity of the methanization reactions, adequate and precise cooling is necessary in order to avoid catalyst deactivation, sintering, and carbon deposition by thermal cracking. 

Supported aqueous phase (SAP) catalysts (16) employ an aqueous film of TPPTS or similar ligand, deposited on a soHd support, eg, controlled pore glass. Whereas these supported catalysts overcome some of the principal limitations experienced using heterogeneous catalysts, including rhodium leaching and rapid catalyst deactivation, SAP catalysts have not found commercial appHcation as of this writing. 

It is possible to deactivate a metal ioa by adding a compouad such as disahcyhdeae alkyl diamiae, which readily forms a chelate with most metal atoms to reader them iaeffective. Metal deactivator has beea showa to reduce oxidatioa deposits dramatically ia the JFTOT test and ia single tube heat exchanger rigs. The role of metal deactivator ia improving fuel stabiUty is complex, siace quantities beyond those needed to chelate metal atoms act as passivators of metal surfaces and as antioxidants (13). 

The appHcations of supported metal sulfides are unique with respect to catalyst deactivation phenomena. The catalysts used for processing of petroleum residua accumulate massive amounts of deposits consisting of sulfides formed from the organometaHic constituents of the oil, principally nickel and vanadium (102). These, with coke, cover the catalyst surface and plug the pores. The catalysts are unusual in that they can function with masses of these deposits that are sometimes even more than the mass of the original fresh catalyst. Mass transport is important, as the deposits are typically formed... 

Catalysts in this service can deactivate by several different mechanisms, but deactivation is ordinarily and primarily the result of deposition of carbonaceous materials onto the catalyst surface during hydrocarbon charge-stock processing at elevated temperature. This deposit of highly dehydrogenated polymers or polynuclear-condensed ring aromatics is called coke. The deposition of coke on the catalyst results in substantial deterioration in catalyst performance. The catalyst activity, or its abiUty to convert reactants, is adversely affected by this coke deposition, and the catalyst is referred to as spent. The coke deposits on spent reforming catalyst may exceed 20 wt %. 

The heat released from the CO—H2 reaction must be removed from the system to prevent excessive temperatures, catalyst deactivation by sintering, and carbon deposition. Several reactor configurations have been developed to achieve this (47). 

The specific rate is expected to have an Arrhenius dependence on temperature. Deactivation by coke deposition in cracking processes apparently has this kind of correlation. 

Some studies of potential commercial significance have been made. For instance, deposition of catalyst some distance away from the pore mouth extends the catalyst s hfe when pore mouth deactivation occui s. Oxidation of CO in automobile exhausts is sensitive to the catalyst profile. For oxidation of propane the activity is eggshell > uniform > egg white. Nonuniform distributions have been found superior for hydrodemetaUation of petroleum and hydrodesulfuriza-tion with molybdenum and cobalt sulfides. Whether any commercial processes with programmed pore distribution of catalysts are actually in use is not mentioned in the recent extensive review of GavriUidis et al. (in Becker and Pereira, eds., Computer-Aided Design of Catalysts, Dekker, 1993, pp. 137-198), with the exception of monohthic automobile exhaust cleanup where the catalyst may be deposited some distance from the mouth of the pore and where perhaps a 25-percent longer life thereby may be attained. 

Deactivation of zeolite catalysts occurs due to coke formation and to poisoning by heavy metals. In general, there are two types of catalyst deactivation that occur in a FCC system, reversible and irreversible. Reversible deactivation occurs due to coke deposition. This is reversed by burning coke in the regenerator. Irreversible deactivation results as a combination of four separate but interrelated mechanisms zeolite dealu-mination, zeolite decomposition, matrix surface collapse, and contamination by metals such as vanadium and sodium. 

These metals, when deposited on the E-cat catalyst, increase coke and gas-making tendencies of the catalyst. They cause dehydrogenation reactions, which increase hydrogen production and decrease gasoline yields. Vanadium can also destroy the zeolite activity and thus lead to lower conversion. The deleterious effects of these metals also depend on the regenerator temperature the rate of deactivation of a metal-laden catalyst increases as the regenerator temperature increases. 

Four pilot plant experiments were conducted at 300 psig and up to 475°C maximum temperature in a 3.07-in. i.d. adiabatic hot gas recycle methanation reactor. Two catalysts were used parallel plates coated with Raney nickel and precipitated nickel pellets. Pressure drop across the parallel plates was about 1/15 that across the bed of pellets. Fresh feed gas containing 75% H2 and 24% CO was fed at up to 3000/hr space velocity. CO concentrations in the product gas ranged from less than 0.1% to 4%. Best performance was achieved with the Raney-nickel-coated plates which yielded 32 mscf CHh/lb Raney nickel during 2307 hrs of operation. Carbon and iron deposition and nickel carbide formation were suspected causes of catalyst deactivation. 

As was noted for experiments HGR-12, HGR-13, and HGR-14, the rate of catalyst deactivation increased as the fresh gas feed rate increased. It is possible that higher rates of carbon deposition and metal sintering occur at the higher feed rates with resultant higher deactivation rates. 

Nickel catalysts were used in most of the methanation catalytic studies they have a rather wide range of operating temperatures, approximately 260°-538°C. Operation of the catalytic reactors at 482°-538°C will ultimately result in carbon deposition and rapid deactivation of the catalysts (10). Reactions below 260°C will usually result in formation of nickel carbonyl and also in rapid deactivation of the catalysts. The best operating range for most fixed-bed nickel catalysts is 288°-482 °C. Several schemes have been proposed to limit the maximum temperature in adiabatic catalytic reactors to 482°C, and IGT has developed a cold-gas recycle process that utilizes a series of fixed-bed adiabatic catalytic reactors to maintain this temperature control. 

---