Datums

It is important to note that the scribed lines are only a guide, and any accurate dimension must be finally checked by measuring. 

The function of a datum is to establish a reference position from which all dimensions are taken and hence all measurements are made. The datum may be a point, an edge or a centre line, depending on the shape of the workpiece. For any plane surface, two datums are required to position a point and these are usually at right angles to each other. 

The datums are established by the draughtsman when the drawing is being dimensioned and, since marking out is merely transferring drawing dimensions to the workpiece, the same datums are used. 

---

An additional advantage derived from plotting the residuals is that it can aid in detecting a bad data point. If one of the points noticeably deviates from the trend line, it is probably due to a mistake in sampling, analysis, or reporting. The best action would be to repeat the measurement. However, this is often impractical. The alternative is to reject the datum if its occurrence is so improbable that it would not reasonably be expected to occur in the given set of experiments. 

Below the temperature of the lowest experimental datum, standard-state fugacities were obtained by simple extrapolation. Uncertainties assigned to these fugacities are largest when the fugacities are smallest, for two reasons (1) the extrapolation... 

Estimated cost casing drilling operation well equipment TOTAL Estimated rig time 000 200 2000 400 2600 28 days Type of well Deviated, oil, development Drilling rig Jolly Roger-1 Datum Level DFE 88ft above MSL Sea Bed 250ft Total Depth 3700ft Conductor No No.8 ... 

In a normal pressure regime the pressure in a hydrocarbon accumulation is determined by the pressure gradient of the overlying water (dP / dD), which ranges from 0.435 psi/ ft (10 kPa/m) for fresh water to around 0.5 psi/ft (11.5 kPa/m) for salt saturated brine. At any depth (D), the water pressure (PJ can be determined from the following equation, assuming that the pressure at the surface datum is 14.7 psia (1 bara) ... 

In a normally pressured reservoir, the pressure is transmitted through a continuous column of water from the surface down to the reservoir. At the datum level at surface the pressure is one atmosphere. The datum level for an offshore location is the mean sea level (msl), and for a onshore location, the ground water level. 

In abnormally pressured reservoirs, the continuous pressure-depth relationship is interrupted by a sealing layer, below which the pressure changes. If the pressure below the seal is higher than the normal (or hydrostatic) pressure the reservoir is termed overpressured. Extrapolation of the fluid gradient in the overpressured reservoir back to the surface datum would show a pressure greater than one atmosphere. The actual value by which the extrapolated pressure exceeds one atmosphere defines the level of overpressure in the reservoir. Similarly, an underpressured reservoir shows an pressure less than one atmosphere when extrapolated back to the surface datum. 

In preparation for a field wide quick look correlation, all well logs need to be corrected for borehole inclination. This is done routinely with software which uses the measured depth below the derrick floor ( alonghole depth below derrick floor AHBDFor measured depth , MD) and the acquired directional surveys to calculate the true vertical depth subsea (TVSS). This is the vertical distance of a point below a common reference level, for instance chart datum (CD) or mean sea level (MSL). Figure 5.41 shows the relationship between the different depth measurements. 

Next, we align all logs at the datum plane which now becomes a straight horizontal line. Note that by doing so we ignore all structural movements to which the sequence has been exposed. 

We can now correlate all events below or above the datum plane by comparing the log response. In many instances correlations are ambiguous. Where two or more correlation... 

Structural maps display the top (and sometimes the base) of the reservoir surface below the datum level. The depth values are always true vertical sub sea. One could say that the contours of structure maps provide a picture of the subsurface topography. They display the shape and extent of a hydrocarbon accumulation and indicate the dip and strike of the structure. The dip is defined as the angle of a plane with the horizontal, and Is perpendicular to the strike, which runs along the plane. 

We now compare the results calculated for the fundamental frequency of the symmetric stretching mode with the only available experimental datum [78] of 326 cm . The theoretical result is seen to exceed experiment by only 8.3%. It should be recalled that the Li3 and Li3 tiimers have for lowest J the values 0 and respectively. Thus, the istopic species Li3 cannot contribute to the nuclear spin weight in Eq. (64), since the calculations for half-integer J should employ different nuclear spin weights. Note that atomic masses have been used... 

In some applications it may be necessary to prescribe a pressure datum at a node at the domain boundary. Although pressure has been eliminated from the working equations in the penalty scheme it can be reintroduced through the penalty terms appearing in the boundary line integrals. 

For a specified mean and standard deviation the number of degrees of freedom for a one-dimensional distribution (see sections on the least squares method and least squares minimization) of n data is (n — 1). This is because, given p and a, for n > 1 (say a half-dozen or more points), the first datum can have any value, the second datum can have any value, and so on, up to n — 1. When we come to find the... 

The possibility that the rate of reaction of benzene is affected by the phenomenon of reaction at the encounter rate is a matter of importance, because benzene is the datum relative to which comparisons of reactivity are made. Up to 68 % sulphuric acid the slope of a plot of log [kffi moU s i) against — + log is unity for data relating to 25 °C, and... 

The behaviour of benzene is the datum from which any discussion of aromatic compoimds must start the reactivity of an aromatic compound is its rate of reaction relative to that of benzene when both are taking part in reactions occurring under the same conditions and proceeding by the same mechanism. 

Actual consumption the difference between actual and apparent consumption is primarily due to inventory changes. U.S. datum is apparent consumption. 

G. C. Datum and S. A. BiUets, Conference Record of the Twenty-Second IEEE Photovoltaic Specialist Conference, 1991, 2, 1422—1428 (1991). 

The purpose of translation is to change the position of the data with respect to the coordinate axes. Usually, the data are translated such that the origin coincides with the mean of the data set. Thus, to mean-center the data, let be the datum associated with the kth measurement on the /th sample. The mean-centered value is computed as = x.f — X/ where xl is the mean for variable k. This procedure is performed on all of the data to produce a new data matrix the variables of which are now referred to as features. 

Cp Heat capacity at constant J/(mol-K) Btu/(lb mopRJ Elevation above a datum m ft... 

The measurement of level can be defined as the determination of the location of the interface between two fluids, separable by gravity, with respecl to a fixed datum plane. The most common level measurement is that of the interface between a liquid and a gas. Other level mea-... 

The distribution of residence times of reactants or tracers in a flow vessel, the RTD, is a key datum for determining reactor performance, either the expected conversion or the range in which the conversion must fall. In this section it is shown how tracer tests may be used to estabhsh how nearly a particular vessel approaches some standard ideal behavior, or what its efficiency is. The most useful comparisons are with complete mixing and with plug flow. A glossary of special terms is given in Table 23-3, and major relations of tracer response functions are shown in Table 23-4. 

Energy in (above datum) -f- energy generated = energy out (above datum)... 

U = Heat transfer coefficient for transfer between the pipeline and surrounding ground, Btu/hr-ft -°F X = Distance from origin, ft Z = Distance above datum, ft = Joule-Thompson coefficient 6 = Incremental amount of a variable... 

In this more general analysis it is essential to be able to define the position and thickness of each ply within a laminate. The convention is that the geometrical mid-plane is taken as the datum. The top and bottom of each ply are then defined relative to this. Those above the mid-plane will have negative co-ordinates and those below will be positive. The bottom surface of the /th ply has address hf and the top surface of this ply has address hj-. Hence the thickness of the /th ply is given by... 

V = wind speed at the datum level (usually the height of the building), m/s... 

---