Corrugated plastic

Finally, what of polymeric materials Corrugated plastic sheet is commonly used for roofing small sheds, car ports and similar buildings but although polymers do not... 

Materials of construction must he corrosion resistant. Steel should he hot galvanized, although some resin coatings may suffice. GRP casings are used hy some manufacturers. The water-dispersal packing of a cooling tower is made of treated timber or corrugated plastic sheet. 

Cushioning materials in widespread use include air bubble sheet, cellulose padding, cork-based granules/sheet, corrugated plastic comers, corrugated sleeves, embossed paper, expanded polystyrene, other expanded plastics, foam in place, free flow polystyrene, sawdust and shavings, straw, wood wool. 

Corrugated plastic can have a double-faced or single-faced construction. The double-faced construction has two linerboards separated by a fluted center. The single-faced construction allows one to form tubes or to shape the material around most cylindrical or round products. Profile plastic is produced as a continuous extrusion with two outer linerboards separated by a vertical flute. Inhibited corrugated and profiled plastics are used for boxes, dividers and partitions between metal surfaces. 

Drain tile- A perforated, corrugated plastic pipe laid at the bottom of the foundation wall and used to drain excess water away from the foundation. It prevents ground water from seeping through the foundation wall. Sometimes called perimeter drain. 

Simple separators (spacers without filtering properties) are made of plastic or ebonite rods or of plastic cords (2 mm in diameter), perforated or corrugated plastic sheets, or fiberglass felts. These separators have large holes or pores (from 0.1 to 4 mm). 

Wisconsin plasnc Dram Tile buys/sells regnnd and someiimes obsolete or surplus virgin resins They operate a cleaning or processing syslem ihat handles post-consumer scrap and make recycled plastic corrugated plastic tubing. They nave been in operaiion lor 15 years. 

Figure 7.10 Exploded view of a Gro E cell (with positive Plante plates). 1 End spacer 2 Negative grid plate 3 Microporous separator 4 Positive Plante plate 5 Corrugated plastic separator 6 Positive plate group 7 Negative plate group 8 Bus bar and pole 9 Lid with slot for glued joint 10 Soft rubber seal 11 Washer 12 Vent plug with cap 13 Plate group 14 Complete Gro E cell in a transparent container.

FIG. 21-49 Application of a noncontact inkjet printing system used for coding plastic bottles and corrugated fiberboard cartons. (VIDEOJET shown, couitesy of VIDEOJET Systems International, Inc., 1500 Mittal Blvd., Wood Dale, IL 60191-1073.)... 

Common materials—such as textiles in the form of fibers or fabrics, foamed rubber, foamed plastics, thin sheets of plastic, paper, corrugated cardboard, combustible dusts, dry grass and twigs, and wood shavings—are all examples of materials with large sutface areas in relation to their volumes. In a well-estabhshed fire, materials with relatively small surface areas, such as chunks of coal or logs, burn readily. 

Fig. 28.14. A design for a small plastic wheel. The upper, corrugated, web profile is better than the lower, ribbed, one because the section is constant.

Plastics have made many major contributions to the contemporary scene. Health-care professionals depend on plastics for everything from intravenous bags to wheelchairs, disposable labware to silicone body parts, etc. The diversity of plastics allows them to serve in many ways, improving and prolonging lives, such as a braided, corrugated Dacron (Du Pont s polyester) aorta tube (24). 

Increasing the stiffness capability of any material (plastic, metal, etc.) can be accomplished by thickening the product. Result is use of more materials and more processing costs. As reviewed, other approaches include the use of ribs, corrugations, and sandwich constructions. 

Different core materials are used. They include foam, honeycomb core (plastic, paper, aluminum, etc.), ribs, balsa wood, filler spacers, corrugated sheet spacers, etc. Materials such as polyurethane foam, cellulosic foams, and polystyrene foams are widely used as core materials. Plastics, such as glass-reinforced polyester, are frequently used as the skins for panels. Different skin materials are used such as metallic skins alone or in conjunction with plastic skins. 

BIB refers to a sealed, sprouted (small too large, with or without dispensing valves) plastic film bag inside a molded rigid container, generally for packaging liquid products. Outer box may be made of disposable corrugated cardboard, disposable or reusable... 

Other surgical implants are essentially plastic repair products for worn out parts of the body. It is possible to conceive of major replacements of an entire organ such as a kidney or a heart by combining the plastic skills with tissue regeneration efforts that may extend life. This is used to time the heart action. Extensively used are plastic corrugated, fiber (silicone or TP polyester) braided aortas (24). 

Thin to large wall Designing around TP problems is the joint responsibility of the product and mold designers. For example, one way to handle the problem of thin to large area walls is by the inclusion of long ribs into the product in the direction of plastic flow. These ribs are not a functional requirement of the product but they act as auxiliary runners attached to the product to facilitate plastic flow in difficult to fill areas. In some instances the ribs may be used as a surface decoration like a corrugation or they may be on the concealed side of the product where they are stiffeners. 

---