Corrosion. Also stress cracking

Corrosion also occurs as a result of the conjoint action of physical processes and chemical or electrochemical reactions (1 3). The specific manifestation of corrosion is deterrnined by the physical processes involved. Environmentally induced cracking (EIC) is the failure of a metal in a corrosive environment and under a mechanical stress. The observed cracking and subsequent failure would not occur from either the mechanical stress or the corrosive environment alone. Specific chemical agents cause particular metals to undergo EIC, and mechanical failure occurs below the normal strength (5aeld stress) of the metal. Examples are the failure of brasses in ammonia environments and stainless steels in chloride or caustic environments. 

Embrittlement embrittlement and for improperly heat treated steel, both of which give intergranular cracks. (Intercrystalline penetration by molten metals is also considered SCC). Other steels in caustic nitrates and some chloride solutions. Brass in aqueous ammonia and sulfur dioxide. physical environments. bases of small corrosion pits, and cracks form with vicious circle of additional corrosion and further crack propagation until failure occurs. Stresses may be dynamic, static, or residual. stress relieve susceptible materials. Consider the new superaustenitic stainless steels. 

Only certain specific environments appear to produce stress corrosion of copper alloys, notably ammonia or ammonium compounds or related compounds such as amines. Mercury or solutions of mercury salts (which cause deposition of mercury) or other molten metals will also cause cracking, but the mechanism is undoubtedly differentCracks produced by mercury are always intercrystalline, but ammonia may produce cracks that are transcrystalline or intercrystalline, or a mixture of both, according to circumstances. As an illustration of this, Edmundsfound that mercury would not produce cracking in a stressed single crystal of brass, but ammonia did. 

As with alloys of other metals, nickel alloys may suffer stress-corrosion cracking in certain corrosive environments, although the number of alloy environment combinations in which nickel alloys have been reported to undergo cracking is relatively small. In addition, intergranular attack due to grain boundary precipitates may be intensified by tensile stress in the metal in certain environments and develop into cracking. Table 4.28 lists the major circumstances in which stress corrosion or stress-assisted corrosion of nickel and its alloys have been recorded in service and also shows the preventive and remedial measures that have been adopted, usually with success, in each case. 

Stress-corrosion cracking occurs in certain aluminium alloys which have been developed for medium and high strength by employing variations in composition, cold work and heat treatment The main alloys are based upon Al-Mg, Al-Mg and Al-Cu, but stress corrosion also occurs in Al-Ag, Al-Cu-Mg, Al-Mg-Si, Al-Zn and Al-Cu-Mg-Zn alloys. It has... 

Where waterside deposits are evident, they provide a heat insulating effect and also permit under-deposit contaminant concentration. Under conditions of high pressure, heat flux, or stress, this combination of factors may lead to the development of embrittlement corrosion or stress corrosion cracking (SCC). 

The problems common to SCWO technologies have also been studied. These include reactor vessel corrosion, stress cracking, and salt plugging. 

Nickel confers excellent resistance to alkaline attack and to stress-cracking corrosion and is also quite resistant to nonoxidizing acids. It is widely used to the extent of a few percent in stainless steels (300 series, see Section 16.8), and in several high nickel alloys, including the following proprietary metals ... 

The environment also plays a role in some environments brittle crack failure is strongly promoted. For example, detergents such as synthetic soaps can decrease the time to brittle failure of PE by a factor between 10 and 50 (see Figure 7.21). This phenomenon is known as stress corrosion or environmental stress cracking (ESC) (see further 8.5). 

Chloride stress cracking corrosion was also a problem when austenitic stainless steels were covered with thermal insulation. The NACE Paper also discusses the protective coatings for stainless steels and provides sandblasting and coating application guides for stainless and carbon steels. 

For detection of more localized corrosion, such as crevice corrosion or SCC, other ultrasonic inspection techniques may be useful. Baseline data generated at the time of installation will also be helpful in evaluating results. One benefit derived from this type of inspection technique is that it can often be conducted with little or no interference with production. Periodic planned visual inspection of equipment utilized under conditions likely to cause stress cracking is also an effective technique, especially when combined with non-destructive inspection techniques such as dye penetrant inspection. It may be necessary to remove coatings or insulation from the equipment surface to facilitate inspection. 

---