Coatings, removal

Cleaning of particle surfaces through collapse of cavity bubbles (e.g., removal of slime coatings, removal of oxidation films, and removal of collector contaminated layers on gauge particle surfaces)... 

End condition Paint coating removed, leaving i-inch mix of paint and... 

Abrefah, J., Marschman, S. C. Jensen, E. D. 1998. Examination of the Surface Coatings Removed from K-East Fuel Elements. Pacific Northwest National Laboratory Report, PNNL-11806. 

If possible, seal the cylinder and return to supplier. Otherwise, wear nitrile rubber gloves, face shield, goggles, breathing equipment, and laboratory coat. Remove leaking cylinder to a safe area outdoors or an efficient fume hood. Fit the cylinder with an appropriate control valve and a length of hose. Discharge the gas slowly into 15% aqueous sodium hydroxide. Cautiously make the sodium hydroxide solution strongly acidic with concentrated hydrochloric acid, and then add sodium sulfite until reaction ceases. After... 

Lambert T Dev V Rechavia E, Forrester J, Litvak p Eigler N. Localized arterial wall drug delivery from a polymer-coated removable metallic stent kinetics, distribution, and bioactivity offorskolin. Circulation 1994 90 1003-101 I. 

Dev Y Eigler N, Sheth S, et al. Kinetics of drug delivery to the arterial wall via polyurethane-coated removable nitinol stent comparative study of two drugs. Cathet Cardiovasc Diagn 1995 34 272-278. 

Certainly, since the publication of those reports in 1976 there has been a vast expansion in the range of uses of bonded molybdenum disulphide coatings, and the problem of coating removal has apparently not been found to be serious, since it seems not to have been highlighted in recent years. 

Figure 28.23 Scanned picture of Prohesion tested samples with different scribe types and depths E-coat removed after test.

Park, H. S., Lee, S. Y., Paek, U. C. and Chung, Y. J. (2005). Noncontact optical fiber coating removal technique with hot air stream. Journal of Lightwave Technology Ti 551-557. 

DCM, 73%, as a constituent of Fine-L-Kote coating remover, manufactured by Tech Spray Inc. 1-800-372-8523. 

Uncertainty of mass loss measurement. The standard method of the neutral salt spray test does not indicate the mass of RS. Mass loss was found as a difference between the RS prepared for the corrosion test and the RS after the corrosion test and corrosion product stripping as well as protective coating removal from the RS (Table 1). Such a mass loss determination is based on three components (1) mass loss determination by weighing (accuracy 0.5 mg and standard deviation 0.3 mg) before the neutral salt spray test and after it, (2) determination of difference and (3) cor-... 

Multiple dip-coating removes defects present in the first layer as shown in Fig. 8.5 for a three-layer y-alumina membrane system. 

Full. Complete coating removal and reapplication techniques required when present... 

Besides the issue of efficiency, the most important consideration in the adoption of any cleaning technique concerns the nature and extent of side effects that may be induced in the substrate. In considering this issue, the subsequent discussion focuses on the side effects of coating removal via ablation, since this case has been examined in great detail and best illustrates the many fundamental questions that are involved in laser cleaning applications. 

PrepRite Coating Remover. [ISP] N-Mediyl-2-pytrolidone, butyrdactone, andothaingreds. 

Uresolve. Pynaloy] Solvents for silicones, ur anes, photo resists, conformal coating removal. 

ORIGIN/INDUSTRY SOURCES/USES dyestuffs manufacture of phenols, aniline, cumene, DDT, chloronitrobenzenes, o-and p- dichlorobenzene insecticides adhesives paints polishes waxes pharmaceuticals textiles dry cleaning surface coatings tar and grease remover surface coating removers natural rubbers heat transfer medium... 

---