Copolymers high-impact polystyrene

Polyacrylonitrile fibers Block copolymers High-impact polystyrene (HIPS)... 

Graft copolymers A Rubber-styrene graft copolymers (high-impact polystyrene)... 

To complete the assembly of a cell, the interleaved electrode groups are bolted to a cov er and the cover is sealed to a container. Originally, nickel-plated steel was the predominant material for cell containers but, more recently plastic containers have been used for a considerable proportion of pocket nickel-cadmium cells. Polyethylene, high impact polystyrene, and a copolymer of propylene and ethylene have been the most widely used plastics. 

Proportion of Hard Segments. As expected, the modulus of styrenic block copolymers increases with the proportion of the hard polystyrene segments. The tensile behavior of otherwise similar block copolymers with a wide range of polystyrene contents shows a family of stress—strain curves (4,7,8). As the styrene content is increased, the products change from very weak, soft, mbbedike materials to strong elastomers, then to leathery materials, and finally to hard glassy thermoplastics. The latter have been commercialized as clear, high impact polystyrenes under the trade name K-Resin (39) (Phillips Petroleum Co.). Other types of thermoplastic elastomers show similar behavior that is, as the ratio of the hard to soft phase is increased, the product in turn becomes harder. 

Around Izod notch Low-density polyethylene Ethylene-propylene block copolymers Cellulose nitrate and propionate ABS and high-impact polystyrene Bis-phenol A polycarbonate... 

In addition to polystyrene and high-impact polystyrene there are other important styrene-based plastics. Most important of these is ABS, with a global capacity of about 5 X 10 t.p.a. and production of about 3 X 10 t.p.a. The styrenic PPO materials reviewed in Chapter 21 have capaeity and production figures about one-tenth those for ABS. Data for the more specialised styrene-acrylonitrile copolymers are difficult to obtain but consumption estimates for Western Europe in the early 1990s were a little over 60000 t.p.a. 

In the late 1940s, the demand for styrene homopolymers (PS) and styrene-acrylonitrile copolymers (SAN) was drastically reduced due to their inherent brittleness. Thus, the interest was shifted to multiphase high-impact polystyrene (HIPS) and rubber-modified SAN (ABS). In principle, both HIPS and ABS can be manufactured by either bulk or emulsion techniques. However, in actual practice, HIPS is made only by the bulk process, whereas ABS is produced by both methods [132,133]. 

In a block copolymer, a long segment made from one monomer is followed by a segment formed from the other monomer. One example is the block copolymer formed from styrene and butadiene. Pure polystyrene is a transparent, brittle material that is easily broken polybutadiene is a synthetic rubber that is very resilient, but soft and opaque. A block copolymer of the two monomers produces high-impact polystyrene, a material that is a durable, strong, yet transparent plastic. A different formulation of the two polymers produces styrene-butadiene rubber (SBR), which is used mainly for automobile tires and running shoes, but also in chewing gum. 

An important class of copolymers made by chain copolymerisation is graft copolymers, synthesized in order to toughen brittle materials through inclusion of a rubber phase. Examples are the cases of styrenic copolymers called "HIPS" for High-Impact Polystyrene and ABS for Acrylonitrile-Butadiene-Styrene. Both are synthesized in two steps. 

The formation of graft copolymers leads to the possibility of combining incompatible polymers in such a way that the components may be distributed homogeneously or they are at least firmly fixed to each other at the phase boundaries, for example, with high-impact polystyrene, where the two components, polystyrene, ( 90%) and rubber ( 10%), are combined through... 

Blends of impact polystyrene with SBS block copolymers give super-high-impact polystyrene. 

Polycarbonate is blended with a number of polymers including PET, PBT, acrylonitrile-butadiene-styrene terpolymer (ABS) rubber, and styrene-maleic anhydride (SMA) copolymer. The blends have lower costs compared to polycarbonate and, in addition, show some property improvement. PET and PBT impart better chemical resistance and processability, ABS imparts improved processability, and SMA imparts better retention of properties on aging at high temperature. Poly(phenylene oxide) blended with high-impact polystyrene (HIPS) (polybutadiene-gra/f-polystyrene) has improved toughness and processability. The impact strength of polyamides is improved by blending with an ethylene copolymer or ABS rubber. 

Although this method yields a mixture of homopolymer and graft copolymer, and probably also ungrafted backbone polymer, some of the systems have commercial utility. These are high-impact polystyrene (HIPS) [styrene polymerized in the presence of poly(l,3-buta-diene)], ABS and MBS [styrene-acrylonitrile and methyl methacrylate-styrene, respectively, copolymerized in the presence of either poly(l,3-butadiene) or SBR] (Sec. 6-8a). 

The third possibility to prepare graft copolymers is termed grafting onto . This means that a growing chain B attacks the polymer backbone A with formation of a long branch. This attack can be a chain-transfer reaction or a copolymerization with unsaturated groups, for example, in polydienes. These reactions play an important role in the preparation of high impact polystyrene (see... 

The term graft copolymer is used to describe copolymers with long sequences of another monomer (comonomer) as branches on the main polymer chain. Most commercial varieties of high-impact polystyrene (HIP) and copolymers of acrylonitrile, butadiene, and styrene (ABS) are graft copolymen in which the main polymer chain is polybutadiene and the branches are styrene, or styrene and acrylonitrile. Figure 1.12 shows various types of copolymers. 

Order-disorder transitions and spinodals were computed for linear multi block copolymers with differing sequence distributions by Fredrickson et al. (1992). This type of copolymer includes polyurethanes, styrene-butadiene rubber, high impact polystyrene (HIPS) and acrylonitrile-butadiene-styrene (ABS) block copolymers. Thus the theory is applicable to a broad range of industrial thermoplastic elastomers and polyurethanes. The parameter... 

ABA ABS ABS-PC ABS-PVC ACM ACS AES AMMA AN APET APP ASA BR BS CA CAB CAP CN CP CPE CPET CPP CPVC CR CTA DAM DAP DMT ECTFE EEA EMA EMAA EMAC EMPP EnBA EP EPM ESI EVA(C) EVOH FEP HDI HDPE HIPS HMDI IPI LDPE LLDPE MBS Acrylonitrile-butadiene-acrylate Acrylonitrile-butadiene-styrene copolymer Acrylonitrile-butadiene-styrene-polycarbonate alloy Acrylonitrile-butadiene-styrene-poly(vinyl chloride) alloy Acrylic acid ester rubber Acrylonitrile-chlorinated pe-styrene Acrylonitrile-ethylene-propylene-styrene Acrylonitrile-methyl methacrylate Acrylonitrile Amorphous polyethylene terephthalate Atactic polypropylene Acrylic-styrene-acrylonitrile Butadiene rubber Butadiene styrene rubber Cellulose acetate Cellulose acetate-butyrate Cellulose acetate-propionate Cellulose nitrate Cellulose propionate Chlorinated polyethylene Crystalline polyethylene terephthalate Cast polypropylene Chlorinated polyvinyl chloride Chloroprene rubber Cellulose triacetate Diallyl maleate Diallyl phthalate Terephthalic acid, dimethyl ester Ethylene-chlorotrifluoroethylene copolymer Ethylene-ethyl acrylate Ethylene-methyl acrylate Ethylene methacrylic acid Ethylene-methyl acrylate copolymer Elastomer modified polypropylene Ethylene normal butyl acrylate Epoxy resin, also ethylene-propylene Ethylene-propylene rubber Ethylene-styrene copolymers Polyethylene-vinyl acetate Polyethylene-vinyl alcohol copolymers Fluorinated ethylene-propylene copolymers Hexamethylene diisocyanate High-density polyethylene High-impact polystyrene Diisocyanato dicyclohexylmethane Isophorone diisocyanate Low-density polyethylene Linear low-density polyethylene Methacrylate-butadiene-styrene... 

Another widely used copolymer is high impact polystyrene (PS-HI), which is formed by grafting polystyrene to polybutadiene. Again, if styrene and butadiene are randomly copolymerized, the resulting material is an elastomer called styrene-butadiene-rubber (SBR). Another classic example of copolymerization is the terpolymer acrylonitrile-butadiene-styrene (ABS). Polymer blends belong to another family of polymeric materials which are made by mixing or blending two or more polymers to enhance the physical properties of each individual component. Common polymer blends include PP-PC, PVC-ABS, PE-PTFE and PC-ABS. 

---