Construction materials plants

Fluorinated polymers stand out sharply against other construction materials for their excellent corrosion resistance and high-temperature stability. In this respect they are not only superior to other plastics but also to platinum, gold, glass, enamel and special alloys. The fluorinated plastics used in process plants are polytetrafluorethylene (PTFE), fluorinated ethylene/ propylene (FEP), polytrifiuoromonochlorethylene (PTFCE) and polyvinyl fluoride (PVF). They are much more expensive than other polymers and so are only economical in special situations [59]. 

Many companies now insist that if use of the wrong grade of steel can affect the integrity of the plant, all steel must be checked for composition before use. This applies to flanges, bolts, welding rods, etc., as well as the raw pipe. Steel can be analyzed easily with a spectrographic analyzer. Other failures caused by the use of the wrong construction material are described in Section 16.1. 

The materials selection procedure for new or replacement plant is crucial to the safe and economic operation of that plant. There is no one correct way to select the appropriate construction material, since for small plant handling toxic or inflammable products the integrity of the plant is high in priority, whereas large plant producing bulk material in a competitive market is more likely to be made of cheaper constructional materials, and the occasional leak or failure may have fewer safety implications. 

Corrosive species in the atmospheres include water, salts and gases. Clean atmospheres contain little other than oxygen, nitrogen, water vapor and a small quantity of carbon dioxide. These species are virtually non-corrosive to any of the common constructional materials for plant at normal temperatures. Steel is susceptible to corrosion in even fairly clean air where water can exist as liquid. For plant operating at temperatures up to approximately 100°C coatings are employed to protect steel if required. In clean air corrosion rates are low, and corrosion is primarily a cosmetic problem, although it may be necessary to prevent mst staining of nearby materials. 

All aspects of the material s chemical, mechanical and physical properties which are included in the specification should be capable of measurement and certification. For critical duties all material supplied should be fully tested and certified by competent approved, independent test laboratories. All items of plant should be purchased with material certification. Additional certification is required in cases where the fabricator, in manufacturing an item of plant, used techniques such as welding or heat treatment which may affect the corrosion behavior of the construction materials. 

Ultrasonic techniques. Wall thickness can be measured to monitor the progress of general corrosion, cracks can be detected and hydrogen blisters identified. Certain construction materials such as cast iron cannot be examined by ultrasound. Skilled operators and specialist equipment is required. Plant can be examined in situ except when it is above 80°C. 

If changes have been made to the process (e.g. if incoming water quality cannot be maintained or other uncertainties arise concerning the corrosion behavior of the construction materials) it is possible to incorporate coupons or probes of the material into the plant and monitor their corrosion behavior. This approach may be used to assist in the materials selection process for a replacement plant. Small coupons (typically, 25 x 50 mm) of any material may be suspended in the process stream and removed at intervals for weight loss determination and visual inspection for localized corrosion. Electrical resistance probes comprise short strands for the appropriate material electrically isolated from the item of plant. An electrical connection from each end of the probe is fed out of the plant to a control box. The box senses the electrical resistance of the probe. The probe s resistance rises as its cross-sectional area is lost through corrosion. 

This technique is based upon the detection of corrosion products, in the form of dissolved metal ions, in the process stream. A thin layer of radioactive material is created on the process side of an item of plant. As corrosion occurs, radioactive isotopes of the elements in the construction material of the plant pass into the process stream and are detected. The rate of metal loss is quantified and local rates of corrosion are inferred. This monitoring technique is not yet in widespread use but it has been proven in several industries. 

Fats and soaps Their excellent resistance to the higher fatty acids makes the austenitic steels valuable constructional materials for plant dealing with hydrogenation or other treatment of oleic, stearic, and similar acids. 

Carbon is a relatively inert element chemically and is used in its graphitic and pre-graphitic forms as a construction material under a variety of corrosive conditions. Modern uses include heat exchangers in chemical plants, consumable electrodes in a variety of metallurgical processes and the components of rocket motors and the moderators of gas- and litiuid-cooled nuclear reactors. The demand for carbon products at the present time is I0 t/year. 

Develop necessary process and design information (Section 3.1). The first step in the analysis is to obtain necessary information in sufficient detail to support the type of evaluation being performed. This can include information about the materials being handled, the process conditions, and other site-specific information such as the type of building construction, occupancy, plant layout, and equipment location. 

Table 9E-9 lists unit operations in the polystyrene plant. The highest temperature is 400°F, in the extruder. From this and Figure 9-5, a temperature factor of 0.04 is obtained. There are no high pressures except in the extruder, and its value is unknown. The pressure factor will be assumed to be zero. Stainless steel is used, so the material factor is 0.2. From Equation 2 a complexity factor of 3.48 can be calculated. A direct process investment cost of 350,000 per functional unit is obtained from Figure 9-7. This means that the cost of constructing the plant when the Engineering News Record Construction Index (ENRCI) is 300 would be 3,150,000. This will be updated to 1960 when the ENRCI was 350, and then the CEPI will be used to obtain the cost in 1974. The resultant cost in 1974 is... 

I think that I started to develop all of these allergies when I moved to Minsk. In the neighborhood where we lived there were plants producing construction materials. Whenever we opened the window there was black dust. There is also a lot of dust because the soil is sandy. When the municipal authorities had the money they sent out special trucks every night to wash the roads. But now they don t have the money, so there is a lot of sand on the roads. 

Generally, cladding is needed to protect materials from corrosion in hostile environments, e.g., concrete in chemical plants. Two of the most widely used construction materials today are concrete and mild steel. There are, however, two things known for certain, namely concrete will crack, and steel will rust. 

Well-to-wheel analysis is a specific form of life-cycle analysis (LCA). In contrast to WTW analysis, LCA typically also takes factors other than global GHG emissions of a product or an energy carrier into consideration (such as air pollutants), including provision of all construction materials for the necessary processing plants and, furthermore, plant decommissioning. The full detail of a general LCA analysis is not needed at the level of policy discussion to reach a broad consensus on alternative fuels or drive systems. As a subset of WTW analysis, well-to-tank (WTT) analysis is often used to separate environmental or economic effects of fuel supplies and drive systems. 

Information about construction materials used in the system may be contained within the plant records and can be useful in evaluating the fate and transport of a particular chemical contaminant through a system. For example, a particular contaminant may adsorb to the pipe material used in a utility s distribution system, and this type of information would be critical in evaluating remediation options following a chemical contamination incident. 

The chemical uses for ethylene prior to World War II were limited, for the most part, to ethylene glycol and ethyl alcohol. After the war, the demand for styrene and polyethylene took off, stimulating ethylene production and olefin plant construction. Todays list of chemical applications for ethylene reads like the WTiat s What of petrochemicals polyethylene, ethylbenzene (a precursor to styrene), ethylene dichloride, vinyl chloride, ethylene oxide, ethylene glycol, ethyl alcohol, vinyl acetate, alpha olefins, and linear alcohols are some of the more commercial derivatives of ethylene. The consumer products derived from these chemicals are found everywhere, from soap to construction materials to plastic products to synthetic motor oils. 

The most important applications of zirconium involve its alloys, Zircaloy. The aUoy offers excellent mechanical and heat-transfer properties and great resistance to corrosion and chemical attack. This, in conjunction with the fact that zirconium has a low neutron absorption cross section, makes this ahoy a suitable choice as a construction material for thermal nuclear reactors and nuclear power plants. Other uses are as an ingredient of explosive mixtures, as getter in vacuum tubes, and in making flash bulb, flash powder (historical), and lamp filaments, in rayon spinnerets, and in surgical appliances. 

In the second Five-Year Development Plan of Saudi Arabia (1975-1980) it was estimated that construction expenditure will reach about SR 300 billion (8). This boom in construction expenditure was due to the urgent need for housing, highways,airports, hospitals, schools, industrial plants, and many other needs to meet the desire of the country to build itself into a developed nation. As a result of the huge projects, shortages in the main locally produced construction materials have occured. 

---