Colloidal from water

A diffusion mechanism is also used in dialysis as a means of separating colloids from crystalloids. The rate of diffusion of molecules in gels is practically the same as in water, indicating the continuous nature of the aqueous phase. The diffusion of gases into a stream of vapour is of considerable importance in diffusion pumps. 

A final are we should discuss is color removal. This is perhaps the most difficult impurity to remove from waters. In surface waters color is associated with dissolved or colloidal suspensions of decayed vegetation and other colloidal suspensions. The composition of this material is largely tannins and lignins, the components that hold together the cellulose cells in vegetation. In addition to their undesirable appearance in drinking water, these organics can cause serious problems in downstream water purification processes. For examples ... 

Flocculation or clarification processes are solids-liquid separation techniques used to remove suspended solids and colloidal particles such as clays and organic debris from water, leaving it clear and bright. Certain chemicals used (such as alums) also exhibit partial dealkaliz-ing properties, which can be important given that the principal alkaline impurity removed is calcium bicarbonate—the major contributory cause of boiler and heat exchanger scales (present in scales as carbonate), although closely followed by phosphate. 

As distinct from the gelling properties of certain natural gums, usually exhibited by structural rigidity, viscosity is a thickening of the aqueous portion of a system by means of particle water absorption, and swelling of the colloid. From a practical angle, it manifests itself by the phenomena of thickening and reduced flow characteristics. 

Chemical precipitation is commonly used to remove heavy metal cations through pH adjustment. However, it is not appropriate to adjust the pH far from neutral for household drinking water applications. Alum (which has only a mild pH effect) is commonly used for the removal of colloids and ions from water.22-23... 

Scheme 9.10 Hydrogenation of anisole by reusable surfactant-stabilized lr(0) colloids in water. TEM micrograph and size distribution of Ir(0). (Adapted from [102].)...

Mechanical agitation of the cream - a process called whipping - creates a metastable foam (i.e. it contains much air). Further whipping causes this foam to collapse some water separates out, and the major product is yellow butter. Incidentally, butter is a different form of colloid from milk, since its dispersed medium is water droplets and its dispersal phase is oil (milk is an oil-in-water colloid). Forming butter from milk is a simple example of emulsion inversion. 

In a study of the bioaccumulation of metals as colloid complexes and free ions by the marine brown shrimp, Penaeus aztecus [29] the colloids were isolated and concentrated from water obtained from Dickinson Bayou, an inlet of Galveston Bay, Texas, using various filtration and ultrafiltration systems equipped with a spiral-wound 1 kDa cutoff cartridge. The total colloidal organic carbon in the concentrate was found to be 78 lmgdm 3. The shrimps were exposed to metals (Mn, Fe, Co, Zn, Cd, Ag, Sn, Ba and Hg) as radiolabelled colloid complexes, and free-ionic radiotracers using ultrafiltered seawater without radiotracers as controls. The experiments were designed so that the animals were exposed to environmentally realistic metal and colloid concentrations. 

Other inorganic reactions shown to be photo-induced at colloidal semiconducting metal oxide surfaces include the synthesis of ammonia from water and nitrogen (19) and the oxidation of halide ions 1 ,... 

Abe, 1., Hayashi, K and Hirashima, T. Prediction of adsorption isotherrrrs of organic compotmds from water on activated carbon,/ Colloid Interface Sci.,% ( ).2Q -2Q(>, 1983. 

Wang, L.K. Role of polyelectrolytes in the filtration of colloidal particles from water and wastewater. Separ. Purif. Meth. 1977, 6 (7), 153-187. 

To eliminate the threat of shock, replenishment of the circulation is essential. With moderate loss of blood, administration of a plasma volume expander may be sufficient Blood plasma consists basically of water, electrolytes, and plasma proteins. However, a plasma substitute need not contain plasma proteins. These can be suitably replaced with macromolecules ( colloids ) that like plasma proteins, (1) do not readily leave the circulation and are poorly filtrable in the renal glomerulus and (2) bind water along with its solutes due to their colloid osmotic properties. In this manner, they will maintain circulatory filling pressure for many hours. On the other hand, volume substitution is only transiently needed and therefore complete elimination of these colloids from the body is clearly desirable. 

The link between colloids and surfaces follows naturally from the fact that particulate matter has a high surface area to mass ratio. The surface area of a 1cm diameter sphere (4jtr ) is 3.14 cm, whereas the surface area of the same amount of material but in the form of 0.1 pm diameter spheres (i.e. the size of the particles in latex paint) is 314 000 cm. The enormous difference in surface area is one of the reasons why the properties of the surface become very important for colloidal solutions. One everyday example is that organic dye molecules or pollutants can be effectively removed from water by adsorption onto particulate activated charcoal because of its high surface area. This process is widely used for water purification and in the oral treatment of poison victims. 

Luisi, P. L., Scartazzini, R., Haering, G., and Schurtenberger, P. (1990). Organogels from water-in-oil microemulsions. Colloid Polymer ScL, 268, 356-74. 

As described in the first part of this section, MVt can reduce protons to give H2 with a platinum catalyst. The presence of Pt colloid in the photoreaction mixture of Ru(bpy) + polymer complex (derived from water soluble homopolymer of Vbpy), MV2+ and EDTA gave H2 gas at almost the same rate as the mixture containing Ru(bpy)j + instead of polymer complex401 (see Scheme 1). The turnover number of the Ru polymer complex exceeded 25 in 1 h s irradiation. The water insoluble polymer complex (5) showed almost the same activity when used as suspensions in a mixture of MeOH/H20 =1/1. 

Finally, vesicles have been used to store reducing equivalents by incorporating C MV1", formed from C14MV2+ on irradiation in the presence of EDTA and [Ru(bipy)3]2+, as multimers (monomers are obtained in the presence of CTAC micelles). These multimers are more stable to air than the monomers but generate hydrogen from water on the addition of carbowax protected colloidal platinum.343... 

At high neutralization levels with alkali metal ions, many ionomers spontaneously form colloidal suspensions in water when stirred vigorously at 100—150°C under pressure. Depending on solids content and acid level, the dispersions range in viscosity from water-like to paste-like. These provide convenient methods for applying thin coatings of ionomers to paper and other substrates. 

The effectiveness of zerovalent iron in removing arsenic from water also greatly depends on the properties of the iron. As(III) removal is especially effective with high surface area 1-120 nm spheres of zerovalent iron (Kanel et al., 2005). Provided that interfering anions (such as, carbonate, silicate, and phosphate) are insignificant, colloidal spheres of zerovalent iron could be injected into arsenic-contaminated soils, sediments, and aquifers for possible in situ remediation (Kanel et al., 2005, 1291). 

---