Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Chromium applications

Bath towels (terry), number produced from one bale of cotton, 8 133t Bathtub failure rate, 26 988 Batik printing, 9 219 Batteries, 3 407-434. See also Alkaline cells Carbon-zinc cells Lead-acid batteries Lithium cells Primary batteries Secondary batteries chromium application, 6 565 cobalt applications, 7 247... [Pg.89]

Photosensitive reactions, chromium application, 6 560-561 Photosensitization, 9 385 of singlet oxygen, 26 804 Photosensitizers, 14 300 23 374-375 diazonaphthoquinone, 15 161-163 Photostability of Al-halamines, 13 100-101 of organic semiconductors, 22 210 Photostimulated drug delivery systems, 9 61, 81... [Pg.704]

Chromium. Applications of chromium plating can be separated into two areas hard chromium, also called functional, industrial, or engineering chromium, and decorative chromium. The plating bath compositions may be the same for both. In most cases, the differentiating factor is plate thickness. Decorative chromium is usually less than about 1 Jim hard chromium can be from about 1 Jm to 500 Jm or more. [Pg.155]

Redox flow batteries, under development since the early 1970s, are stUl of interest primarily for utility load leveling applications (77). Such a battery is shown schematically in Figure 5. Unlike other batteries, the active materials are not contained within the battery itself but are stored in separate tanks. The reactants each flow into a half-ceU separated one from the other by a selective membrane. An oxidation and reduction electrochemical reaction occurs in each half-ceU to generate current. Examples of this technology include the iron—chromium, Fe—Cr, battery (79) and the vanadium redox cell (80). [Pg.587]

Chromium is able to use all of its >d and As electrons to form chemical bonds. It can also display formal oxidation states ranging from Cr(—II) to Cr(VI). The most common and thus most important oxidation states are Cr(II), Cr(III), and Cr(VI). Although most commercial applications have centered around Cr(VI) compounds, environmental concerns and regulations ia the early 1990s suggest that Cr(III) may become increasingly important, especially where the use of Cr(VI) demands reduction and incorporation as Cr(III) ia the product. [Pg.133]

For medium- to high-impact applications a wide range of low-alloy steels are produced containing some chromium, molybdenum, phosphorus, and silicon. Economy of manufacture is a benefit for selec tion of these steels. [Pg.1830]

Metal oxides, sulfides, and hydrides form a transition between acid/base and metal catalysts. They catalyze hydrogenation/dehydro-genation as well as many of the reactions catalyzed by acids, such as cracking and isomerization. Their oxidation activity is related to the possibility of two valence states which allow oxygen to be released and reabsorbed alternately. Common examples are oxides of cobalt, iron, zinc, and chromium and hydrides of precious metals that can release hydrogen readily. Sulfide catalysts are more resistant than metals to the formation of coke deposits and to poisoning by sulfur compounds their main application is in hydrodesulfurization. [Pg.2094]

Actually, in many cases strength and mechanical properties become of secondaiy importance in process applications, compared with resistance to the corrosive surroundings. All common heat-resistant alloys form oxides when exposed to hot oxidizing environments. Whether the alloy is resistant depends upon whether the oxide is stable and forms a protective film. Thus, mild steel is seldom used above 480°C (900°F) because of excessive scaling rates. Higher temperatures require chromium (see Fig. 28-25). Thus, type 502 steel, with 4 to 6 percent Cr, is acceptable to 620°C (I,I50°F). A 9 to 12 percent Cr steel will handle 730°C (I,350°F) 14 to 18 percent Cr extends the limit to 800°C (I,500°F) and 27 percent Cr to I,I00°C (2,000°F). [Pg.2464]

Furnace tubes, piping, and exchanger tubing with metal temperatures above 800°F now tend to be an austenitic stainless steel, e.g., Type 304, 321, and 347, although the chromium-molybdenum steels are still used extensively. The stainless steels are favored beeause not only are their creep and stress-rupture properties superior at temperatures over 900°F, but more importantly because of their vastly superior resistance to high-temperature sulfide corrosion and oxidation. Where corrosion is not a significant factor, e.g., steam generation, the low alloys, and in some applications, carbon steel may be used. [Pg.261]

One other case Involving metal compounds should be noted. Some metal compounds may contain more than one listed metal. For example, lead chromate Is both a lead compound and a chromium compound. In such cases, if applicable... [Pg.30]

Corrective Action Application At a RCRA site in the southwest, a waste stream containing hexavalent chromium was reduced to the trivalent form. The trivalent chromium was then removed using ion exchange. The influent hexavalent chromium... [Pg.147]

Precipitation is often applied to the removal of most metals from wastewater including zinc, cadmium, chromium, copper, fluoride, lead, manganese, and mercury. Also, certain anionic species can be removed by precipitation, such as phosphate, sulfate, and fluoride. Note that in some cases, organic compounds may form organometallic complexes with metals, which could inhibit precipitation. Cyanide and other ions in the wastewater may also complex with metals, making treatment by precipitation less efficient. A cutaway view of a rapid sand filter that is most often used in a municipal treatment plant is illustrated in Figure 4. The design features of this filter have been relied upon for more than 60 years in municipal applications. [Pg.246]

Low-carbon, low-alloy steels are in widespread use for fabrication-welded and forged-pressure vessels. The carbon content of these steels is usually below 0.2%, and the alloying elements that do not exceed 12% are nickel, chromium, molybdenum, vanadium, boron and copper. The principal applications of these steels are given in Table 3.8. [Pg.64]


See other pages where Chromium applications is mentioned: [Pg.100]    [Pg.150]    [Pg.227]    [Pg.228]    [Pg.290]    [Pg.516]    [Pg.545]    [Pg.566]    [Pg.708]    [Pg.790]    [Pg.935]    [Pg.1024]    [Pg.156]    [Pg.100]    [Pg.150]    [Pg.227]    [Pg.228]    [Pg.290]    [Pg.516]    [Pg.545]    [Pg.566]    [Pg.708]    [Pg.790]    [Pg.935]    [Pg.1024]    [Pg.156]    [Pg.224]    [Pg.403]    [Pg.337]    [Pg.348]    [Pg.348]    [Pg.113]    [Pg.120]    [Pg.188]    [Pg.670]    [Pg.787]    [Pg.1830]    [Pg.256]    [Pg.14]    [Pg.474]    [Pg.242]    [Pg.203]    [Pg.44]    [Pg.220]    [Pg.405]    [Pg.969]    [Pg.338]    [Pg.158]    [Pg.317]    [Pg.481]    [Pg.72]   
See also in sourсe #XX -- [ Pg.373 ]

See also in sourсe #XX -- [ Pg.266 ]

See also in sourсe #XX -- [ Pg.168 ]




SEARCH



Application of Chromium Carbene Complexes

Applications for Chromium Compounds

Chromium commercial application

Chromium complexes applications

Chromium oxide applications

Chromium plating applications

Nickel-chromium alloys applications

Nickel-chromium plating, applications

Properties and Applications of Chromium(III) Oxide

Synthesis applications with chromium complexes

© 2024 chempedia.info