Characterisation methods temperature

In this paper we present a new characterisation method for porous carbonaceous materials. It is based on a theoretical treatment of adsorption isotherms measured in wide temperature (303 to 383 K) and pressure ranges (0 to 10000 kPa) and for different adsorbates (N2, CH4, Ar, C3H8 and n-C4Hio). The theoretical treatment relies on the Integral Adsorption Equation concept. We developed a local adsorption isotherm model based on the extension of the Redlich-Kwong equation of state to surface phenomena and we improved it to take into account the multilayer formation. The pore size distribution fimction is assumed to be a bi-modal gaussian. By a minimisation procedure, it is possible to determine the bi-modal pore size distribution function witch can be used for purely characterisation purposes or to predict adsorption isotherms. 

Finally, all three electronic characterisation methods indicate deviations from the expected Hoestery-Letson behaviour at temperatures between 360 K and 400 K where the structural phase transition was identified by X-ray diffraction. The deviation of the //(r)-characteristic from the expected trapping-and-release behaviour starts at a lower temperature for the in-plane FET transport than for the SCLC or TOF transport along the surface normal. Moreover, the temperature interval where the in-plane transport is affected by structural changes amounts to at least 60 K and appears to be much broader than that for the out-of-plane transport. 

Measurement of the initial permeability as a function of temperature can therefore be used as a material characterisation method. The value of Tq depends only on the composition the verticality of the permeability drop at the Curie point indicates the degree of homogeneity in the sample composition (Cedillo et at., 1980 Valenzuela, 1980). 

The refractive index of a liquid is recorded as where t is the temperature at which the measurement is made, and D refers to the wave length of the D line of sodium. As already pointed out, it is usual to determine both the refractive index and the density of the liquid at 20° in any case they should be determined at the same temperatme. These two constants are useful in assisting the characterisation of a pure hquid they are particularly valuable for ahphatic hydrocarbons and similar compounds where the methods of characterisation by the formation of solid derivatives are not entirely satisfactory. 

The procedures of measuring changes in some physical or mechanical property as a sample is heated, or alternatively as it is held at constant temperature, constitute the family of thermoanalytical methods of characterisation. A partial list of these procedures is differential thermal analysis, differential scanning calorimetry, dilatometry, thermogravimetry. A detailed overview of these and several related techniques is by Gallagher (1992). 

This second group of tests is designed to measure the mechanical response of a substance to applied vibrational loads or strains. Both temperature and frequency can be varied, and thus contribute to the information that these tests can provide. There are a number of such tests, of which the major ones are probably the torsion pendulum and dynamic mechanical thermal analysis (DMTA). The underlying principles of these dynamic tests have been covered earlier. Such tests are used as relatively rapid methods of characterisation and evaluation of viscoelastic polymers, including the measurement of T, the study of the curing characteristics of thermosets, and the study of polymer blends and their compatibility. They can be used in essentially non-destructive modes and, unlike the majority of measurements made in non-dynamic tests, they yield data on continuous properties of polymeric materials, rather than discontinuous ones, as are any of the types of strength which are measured routinely. 

Alternative approaches consist in heat extraction by means of thermal analysis, thermal volatilisation and (laser) desorption techniques, or pyrolysis. In most cases mass spectrometric detection modes are used. Early MS work has focused on thermal desorption of the additives from the bulk polymer, followed by electron impact ionisation (El) [98,100], Cl [100,107] and field ionisation (FI) [100]. These methods are limited in that the polymer additives must be both stable and volatile at the higher temperatures, which is not always the case since many additives are thermally labile. More recently, soft ionisation methods have been applied to the analysis of additives from bulk polymeric material. These ionisation methods include FAB [100] and LD [97,108], which may provide qualitative information with minimal sample pretreatment. A comparison with FAB [97] has shown that LD Fourier transform ion cyclotron resonance (LD-FTTCR) is superior for polymer additive identification by giving less molecular ion fragmentation. While PyGC-MS is a much-used tool for the analysis of rubber compounds (both for the characterisation of the polymer and additives), as shown in Section 2.2, its usefulness for the in situ in-polymer additive analysis is equally acknowledged. 

Principles and Characteristics Less well-characterised extraction methods include solvent leaching at high temperature with forced-solvent flow. In the... 

Berger [340] has examined the use of pSFC in polymer/additive analysis. As many polymer additives are moderately polar and nonvolatile SFC is an appropriate separation technique at temperatures well below those at which additives decompose [300,341,342], SFC is also a method of choice for additives which hydrolyse easily. Consequently, Raynor et al. [343] and others [284,344] consider that SFC (especially in combination with SFE) is the method of choice for analysing polymer additives as a relatively fast and efficient sample preparation method. Characterisation of product mixtures of nonpolar to moderately polar components encompassing a wide range of molecular masses can be accomplished by cSFC-FID. Unknown polymer additives may be identified quite adequately by means of cSFC-FID by comparison with retention times of standards [343], However, identification by this method tends to be time-consuming and requires that all the candidate compounds are on hand. SFC-FID of some low-to-medium polarity additives on reversed-phase packed columns... 

The properties of a polymer network depend not only on the molar masses, functionalities, chain structures, and proportions of reactants used to prepare the network but also on the conditions (concentration and temperature) of preparation. In the Gaussian sense, the perfect network can never be obtained in practice, but, through random or condensation polymerisations(T) of polyfunctional monomers and prepolymers, networks with imperfections which are to some extent quantifiable can be prepared, and the importance of such imperfections on network properties can be ascertained. In this context, the use of well-characterised random polymerisations for network preparation may be contrasted with the more traditional method of cross-linking polymer chains. With the latter, uncertainties can exist with regard to the... 

UV/visible spectroscopy of organometallic transients has been extremely important for kinetic measurements on previously identified species, but the spectra are less valuable for structural identification since most spectra show broad and featureless bands. One way round this problem has been to utilise matrix IR spectroscopy for characterisation and to use the data obtained from the matrix UV/visible spectrum to monitor the room-temperature kinetics. A more satisfactory method is to record the IR spectra of transients directly and there has been much activity in both gas phase and solution organometallic chemistry this field has been recently reviewed ( 35). In our laboratory,... 

We conclude that for organometallic derivatives, radiolysis can be used as an excellent method for inducing specific electron-loss or electron-addition. Furthermore, this can be done at very low temperatures such that, often, the primary gain and loss species are formed and can be characterised by e.s.r. spectroscopy. Thus this technique is a useful complement to more conventional studies of redox reactions. 

NMR) [24], and Fourier transform-infrared (FT-IR) spectroscopy [25] are commonly applied methods. Analysis using mass spectrometric (MS) techniques has been achieved with gas chromatography-mass spectrometry (GC-MS), with chemical ionisation (Cl) often more informative than conventional electron impact (El) ionisation [26]. For the qualitative and quantitative characterisation of silicone polyether copolymers in particular, SEC, NMR, and FT-IR have also been demonstrated as useful and informative methods [22] and the application of high-temperature GC and inductively coupled plasma-atomic emission spectroscopy (ICP-AES) is also described [5]. 

Vanadium phosphorus oxides (VPO) are commercially used as catalysts for the s5mthesis of maleic anhydride from the partial oxidation of n-butane. The phase constitution and the morphology of the catalyst are found to be dependent on the preparation routes and the applied solvent [78]. Recently, a method to prepare VPO catalysts in aqueous solution at elevated temperature was reported [79]. In addition to the linear relationship between specific activity and surface area, a small group of catalysts exhibit enhanced activity, which could be due to the combination of a higher proportion of V phases in the bulk of vanadyl pyrophosphate (V0)2P207 catalyst [79, 80]. With high relevance to the catalytic properties, the microstructure characterisation of VPO therefore is of great importance. 

---