Determination cerium

The production of cerium derivatives begins with ore beneficiation and production of a mineral concentrate. Attack on that concentrate to create a suitable mixed lanthanide precursor for later separation processes follows. Then, depending on the relative market demand for different products, there is either direct production of a cerium-rich material, or separation of the mixed lanthanide precursor into individual pure lanthanide compounds including compounds of pure cerium, or both. The starting mineral determines how the suitable mixed lanthanide precursor is formed. In contrast the separation... 

Ln(II) in LnFj Ln(II) were determined after samples dissolution in H PO in the presence of a titrated solution of NFI VO, which excess was titrated with the Fe(II) salt. It was found that dissolution of the materials based on CeF CeFj in H PO does not change the oxidation state of cerium, thus phosphate complexes of Ce(III, IV) can be used for quantitative spectrophotometric determination of cerium valence forms. The contents of Ln(II, III) in Ln S LnS may be counted from results of the determination of total sulfur (determined gravimetric ally in BaSO form) and sum of the reducers - S and Ln(II) (determined by iodometric method). 

Cerium is one of the most widely used activators, which improve the working characteristics of many scintillators. Determination of the valence state of cerium in single crystals of alkaline and rare-earth borates allows to establish the nature of activator centers for purposeful influence on the scintillation efficiency of the matrix. 

To determine of Ce(IV) in acid soluble single crystals, a simple and sensitive method is proposed. The method is based on the reaction of tropeoline 00 oxidation by cerium(IV) in sulfuric acid solution with subsequent measurement of the light absorption decrease of the solution. The influence of the reagent concentration on the analysis precision is studied. The procedure for Ce(IV) determination in ammonium dihydrophosphate doped by cerium is elaborated. The minimal determined concentration of cerium equal to 0.04 p.g/ml is lower than that of analogous methods by a factor of several dozens. The relative standard deviation does not exceed 0.1. 

The total cerium content in the single crystal samples on the basis of rare-earth elements is determined by photometry after Ce(III) oxidation by ammonium persulfate. The Ce(III) content is calculated from the difference. Comparison of the determination results of the total cerium content obtained by photometric and atomic emission methods for Li GdlBO ljiCe demonstrated the elaborated procedure precision and systematic error absence. 

This method involves very simple and inexpensive equipment that could be set up m any laboratory [9, 10] The equipment consists of a 250-mL beaker (used as an external half-cell), two platinum foil electrodes, a glass tube with asbestos fiber sealed m the bottom (used as an internal half-cell), a microburet, a stirrer, and a portable potentiometer The asbestos fiber may be substituted with a membrane This method has been used to determine the fluoride ion concentration in many binary and complex fluondes and has been applied to unbuffered solutions from Willard-Winter distillation, to lon-exchange eluant, and to pyrohydrolysis distil lates obtained from oxygen-flask or tube combustions The solution concentrations range from 0 1 to 5 X 10 M This method is based on complexing by fluonde ions of one of the oxidation states of the redox couple, and the potential difference measured is that between the two half-cells Initially, each cell contains the same ratio of cerium(IV) and cerium(tll) ions... 

Accurate atomic weight values do not automatically follow from precise measurements of relative atomic masses, however, since the relative abundance of the various isotopes must also be determined. That this can be a limiting factor is readily seen from Table 1.3 the value for praseodymium (which has only 1 stable naturally occurring isotope) has two more significant figures than the value for the neighbouring element cerium which has 4 such isotopes. In the twelve years since the first edition of this book was published the atomic weight values of no fewer than 55 elements have been improved, sometimes spectacularly, e.g. Ni from 58.69( 1) to 58.6934(2). 

The aforementioned inconsistencies between the paralinear model and actual observations point to the possibility that there is a different mechanism altogether. The common feature of these metals, and their distinction from cerium, is their facility for dissolving oxygen. The relationship between this process and an oxidation rate which changes from parabolic to a linear value was first established by Wallwork and Jenkins from work on the oxidation of titanium. These authors were able to determine the oxygen distribution in the metal phase by microhardness traverses across metallographic sections comparison of the results with the oxidation kinetics showed that the rate became linear when the metal surface reached oxygen... 

In Sections 10.11-10.16 it is shown how the change in pH during acid-base titrations may be calculated, and how the titration curves thus obtained can be used (a) to ascertain the most suitable indicator to be used in a given titration, and (b) to determine the titration error. Similar procedures may be carried out for oxidation-reduction titrations. Consider first a simple case which involves only change in ionic charge, and is theoretically independent of the hydrogen-ion concentration. A suitable example, for purposes of illustration, is the titration of 100 mL of 0.1M iron(II) with 0.1M cerium(IV) in the presence of dilute sulphuric acid ... 

Cerium(IV) sulphate may be employed in the determination of reducing agents in the presence of a high concentration of hydrochloric acid (contrast potassium permanganate, Section 10.92). 

Method B Standardisation with sodium oxalate. Standardisation may also be carried out with sodium oxalate in this case, an indirect procedure must be used as the redox indicators are themselves oxidised at the elevated temperatures which are necessary. The procedure, therefore, is to add an excess of the cerium(IV) solution, and then, after cooling, the excess is determined by... 

Practically all the determinations described under potassium permanganate and potassium dichromate may be carried out with cerium(IV) sulphate. Use is made of the various indicators already detailed and also, in some cases where great accuracy is not required, of the pale yellow colour produced by the cerium(IV) sulphate itself. Only a few determinations will, therefore, be considered in some detail. 

Discussion. Satisfactory results are obtained by adding the nitrite solution to excess of standard 0.1 M cerium(IV) sulphate, and determining the excess of cerium(IV) sulphate with a standard iron(II) solution (compare Section 10.96). 

Determine the volume of the standard cerium(IV) sulphate solution which has reacted with the nitrite solution, and therefrom calculate the purity of the sodium nitrite employed. 

An excess of a standard solution of iron(II) must therefore be added and the excess back-titrated with standard cerium(IV) sulphate solution. Erratic results are obtained, depending upon the exact experimental conditions, because of induced reactions leading to oxidation by air of iron(II) ion or to decomposition of the persulphate these induced reactions are inhibited by bromide ion in concentrations not exceeding 1M and, under these conditions, the determination may be carried out in the presence of organic matter. 

Determination of cerium as cerium(IV) iodate and subsequent ignition to cerium(IV) oxide Discussion. Cerium may be determined as cerium(IV) iodate, Ce(I03)4, which is ignited to and weighed as the oxide, Ce02. Thorium (also titanium and zirconium) must, however, be first removed (see Section 11.44) the method is then applicable in the presence of relatively large quantities of lanthanides. Titrimetric methods (see Section 10.104 to Section 10.109) are generally preferred. 

Determination of thorium as sebacate and subsequent ignition to the oxide, ThOa Discussion. This procedure permits of the separation by a single precipitation of thorium from relatively large amounts of the lanthanides (Ce, La, Pr, Nd, Sm, Gd) and also from cerium(IV). 

No satisfactory direct gravimetric procedure is available but nitrite can be oxidised to nitrate by permanganate or cerium(IV) and then determined in that form. The determination of total nitrate + nitrite is an important analysis, e.g. for soil samples. Nitrite may be destroyed using urea, sulphamic acid or hydrazine sulphate the reaction with the former is ... 

Discussion. Small amounts of chromium (up to 0.5 per cent) may be determined colorimetrically in alkaline solution as chromate uranium and cerium interfere, but vanadium has little influence. The transmittance of the solution is measured at 365-370 nm or with the aid of a filter having maximum transmission in the... 

Aravamudan and Venkappayya75 oxidized dimethyl sulphoxide in acetate buffer of pH 4 to 4.5 and with a reaction time of only 1 min. They then added potassium iodide and acid and titrated with thiosulphate the iodine liberated by unused reagent. They reported that cerium(IV) and Cr(VI) were much less effective oxidizing reagents for the sulphoxide. A very similar procedure was used by Rangaswama and Mahadevappa76 to determine dimethyl sulphoxide and numerous other compounds with chloramine B. 

The crystal structures of Hf 2 (OH) 2 (S0O 3 (H2O) i, (14) and Ce2(0H)2(S0i,)3 (H20)it (14) also have been determined and found to be isomorphous to the zirconium compound. The cell constants for this series of four isomorphous compounds reflect the effect of the ionic radii on the dimensions of the unit cell. The values for these cell constants are in Table II. Thus, the cell constants for the zirconium and hafnium compounds are nearly identical and smaller than the cell constants for the cerium and plutonium compounds which are also nearly identical. This trend is exactly that followed by the ionic radii of these elements. 

M(0H)2SOi, H2O where M=Zr (8), Hf (12) also have been determined and reveal the presence of almost planar zigzag chains of metal atoms joined by double hydroxide bridges. The single exception to this trend toward formation of double hydroxy-bridged metal dimers or chains is the compound which is best described as CeOSOif,H20 (17). However, even in this structure the cerium ions form chains which are linked by bridging oxide ions. 

E.22 (a) How many CaH2 formula units are present in 5.294 g of CaH2 (b) Determine the mass of 6.25 X 1024 formula units of NaBF4, sodium tetrafluoroborate. (c) Calculate the amount (in moles) of 9.54 X 1021 formula units of Cel3, cerium(III) iodide, a bright yellow, water-soluble solid. 

Sflf-Test L.4A A sample of clay of mass 20.750 g for use in making ceramics was analyzed to determine its iron content. The clay was washed with hydrochloric acid, and the iron converted into iron(II) ions. The resulting solution was titrated with cerium(IV) sulfate solution ... 

Returning to the explanation of induced reactions, we can say the following. Friend s proposal , according to which the error in the H2O2 determination is caused by reaction (83) catalyzed by manganese(II) or cerium(III) formed in the primary reaction between hydrogen peroxide and permanganate or cerium(IV) cannot be accepted. The reaction between the ions mentioned and peroxydisulphate at room temperature is very slow, and, furthermore, the increase in acidity —in contrast to its effect on the induced reaction —promotes the oxidation. There is... 

Powder XR diffraction spectra confirm that all materials are single phase solid solutions with a cubic fluorite structure. Even when 10 mol% of the cations is substituted with dopant the original structure is retained. We used Kim s formula (28) and the corresponding ion radii (29) to estimate the concentration of dopant in the cerium oxide lattice. The calculated lattice parameters show that less dopant is present in the bulk than expected. As no other phases are present in the spectrum, we expect dopant-enriched crystal surfaces, and possibly some interstitial dopant cations. However, this kind of surface enrichment cannot be determined by XR diffraction owing to the lower ordering at the surface. 

---