Cellulose blended with

FKuR also introduced Biograde 200C in 2005, an unfilled cellulose blend with high stiffness and transparency for cast film and injection moulding. The material can also be blow moulded into bottles and thermoformed into cups and trays. Injection moulded Biograde 200C exhibits properties comparable to polystyrene, but with the addition of barrier performance comparable to PLA. It consists of 100% renewable resources, but does not contain starch. 

Crystalline cellulose, hydroxypropyl cellulose, and Carbopol 934 have been studied in combination with lyophilized insulin as bioadhesive powder dosage forms for nasal delivery. Each formulation tested resulted in an decrease in plasma glucose level after nasal administration in dog and rabbit models. The most effective formulation, crystalline cellulose blended with insulin, decreased the plasma glucose level to 49% of the control value. In ternary systems the lyophilized Carbopol 934 and insulin blend with crystalline cellulose powder has been the most effective, leading to a hypoglycemia on the order of one-third of the effect obtained after intravenous injection of the same dose of insulin. The plasma glucose levels obtained in the volunteers after administration of the insulin-Carbopol-crystalline cellulose powder formulation were quite variable [38],... 

Cellulose blends with synthetic polymers also constitute an example of biodegradable polymer blends. Miscibility of cellulose with polyvinylpyrrolidone [Masson and Manley, 1991a], poly(4-vinyl pyridine) [Mason and Manley, 1991b], PAN [Nishio et al, 1987], PVAL [Nishio and Manley, 1988], and polyethyleneoxide (PEG) [Nishio et al., 1989] have been reported. Starch blends with commodity polymers have been commercialized as a low cost method to promote partial environmental degradability. While a defi-... 

No.26, 1998,p.6899-904 CELLULOSIC BLENDS WITH POLY(ACRYLONITRILE) CHARACTERIZATION OF HYDROGEN BONDS USING REGIOSELECTIVELY METHYLATED CELLULOSE DERIVATIVES Shin J-H Kondo T... 

Shin J.-H., Kondo X, Cellulosic blends with poly(acrylonitiile) Characterization of hydrogen bonds using regioselectively methylated cellulose derivatives. Polymer, 39, 1998, 6899-6904. 

Plates homemade (20 x 5 cm), microcrystalline cellulose blended with d-quartz or Na, K-d-tartrate Visualization Na2S solution Plates cellulose powder, Merck, FRG Visualization ninhydrin... 

Other blends such as polyhydroxyalkanoates (PHA) with cellulose acetate (208), PHA with polycaprolactone (209), poly(lactic acid) with poly(ethylene glycol) (210), chitosan and cellulose (211), poly(lactic acid) with inorganic fillers (212), and PHA and aUphatic polyesters with inorganics (213) are receiving attention. The different blending compositions seem to be limited only by the number of polymers available and the compatibiUty of the components. The latter blends, with all natural or biodegradable components, appear to afford the best approach for future research as property balance and biodegradabihty is attempted. Starch and additives have been evaluated ia detail from the perspective of stmcture and compatibiUty with starch (214). 

The FR characteristics of PCP and Anorin-38 were improved substantially by introducing bromine. When five bronine atoms were introduced by controlled bromi-nation, the resin (the product obtained was still fluid in nature and could be crosslinked by hexamine to get hard partially brominated PCP-PBPCP) showed excellent FR characteristics exhibiting self-extinguishing property and UL 94 V-0 grade when blended with polyethylene, NR, etc. There was excellent compatibility with polyolefins as well as with other polymers such as cellulose, polyurethane, etc. Table 13 shows the FR properties of NR-PBPCP. 

Improvement in the solvent and oil resistance of rubbers can be achieved via grafting of acrylonitrile onto rubber [140-142] and rubber blends [143]. The careful control of the degree of grafting allows vulcanized rubber with high-mechanical properties compared with ungrafted vulcanized rubber to be obtained. Also, acid resistance [144] and resistance to microbiological attack [145,146] was improved for cellulose grafted with acrylonitrile, and increases in base resistance were also noted for MMA and a mixture of MMA and ethyl acrylate [13],... 

The exceptional ability of PCL to form blends with many other polymers has stimulated a large amount of research. The subject has been reviewed a number of times (7,8). To date, the potential of such blends for drug delivery has been largely unexploited. The permeability of blends of PCL with cellulose propionate, cellulose... 

Essentially nonionic soil-release agents comprise polyesters, polyamides, polyurethanes, polyepoxides and polyacetals. These have been used mainly on polyester and polyester/ cellulosic fabrics, either crosslinked to effect insolubilisation (if necessary) or by surface adsorption at relatively low temperature. Polyester soil-release finishes have been most important, particularly for polyester fibres and their blends with cellulosic fibres. These finishes, however, have much lower relative molecular mass (1000 to 100 000) than polyester fibres and hence contain a greater proportion of hydrophilic hydroxy groups. They have been particularly useful for application in laundering processes. These essentially nonionic polymers may be given anionic character by copolymerising with, for example, the carboxylated polymers mentioned earlier these hybrid types are generally applied with durable press finishes. 

Figure 9 Adsorption (rag/g) dependence of nonionic cellulose ethers (2500 ppm) on salinity (N, NaCl) of aqueous solution. Substrate Berea sand (85 wt.%) blended with montraorillonite (15 wt.%). W-SP symbols ...

The versatility of this system is reflected in its suitability for blends of wool with other fibres [89]. The ideal conditions for the dyeing of wool/acrylic blends are at pH 4-5 and Albegal SET inhibits the risk of co-precipitation between Lanaset anionic dyes and basic dyes. Lanaset dyes are quite stable when dyeing polyester/wool at pH 4-5 and 115-120°C using Irgasol HTW (Ciba) as wool protectant. These dyes are also suitable for dyeing wool in its blends with silk, nylon or cellulosic fibres. 

Several other resins can be blended with alkyd resins to introduce desired improvement in properties, e. g. cellulose nitrate, chlorinated rubber, phenolics, amino resins or silicons oils. Vinyl monomers like styrene can be added to alkyd resins along with initiator to get a tougher resin with shorter drying times and lighter colour. 

Solubility Behaviour of Cellulose-Reinforced Starch-PVA Blends with Insertion of Fly-Ash... 

Recent studies in this laboratory on hydroxypropyl cellulose (HPC) blends with lignin (9,10) have indicated that the composite morphology and properties are extremely sensitive to the degree of miscibility between the two components. This paper summarizes the observations that have been made with particular regard to the development of high-strength composites. For experimental details, the reader is referred to the above referenced publications. 

There are several methods of manufacturing is on a commercial scale, for instance the calcination of oxalic add blended with potassium chloride, treatment of sodium chlorite with chlorine, or of sodium chlorate with sulphur dioxide in the presence of concentrated sulphuric add. Chlorine dioxide is utilized as a strong bleaching agent for cellulose, paper, flour, oils and such like, as well as a solvent for removing lignin from wood pulp. 

---