Carbon dioxide critical

Fig. 16.1. Phase diagram for carbon dioxide critical temperature 31.3°C critical pressure 72.9 atm.

Enzymes can also be used in supercritical fluids (6,7), the most widely used being supercritical carbon dioxide (critical pressure 31.1°C, critical temperature 7382 kPa). The main difficulty with supercritical fluids, apart from the increased cost imposed by the high-pressure equipment, comes from the fact that properties such as solubility and reaction rates depend strongly on the pressure, making the optimization and operation of processes difficult. 

To prepare scanning electron microscopic specimens, the cells were fixed in 2.5% glu-taraldehyde for 30 min and in 1% osmium tetraoxide for 30 min. After dehydration with serial ethanol, the cells were treated with the carbon dioxide critical point drying technique followed by a gold-platinum coating in vacuum evaporation and examined by a scanning electron microscope (Japan Electric Co., Model TSM 840). 

The majority of practical micellar systems of Tionnal micelles use water as tire main solvent. Reverse micelles use water immiscible organic solvents, altlrough tire cores of reverse micelles are usually hydrated and may contain considerable quantities of water. Polar solvents such as glycerol, etlrylene glycol, fonnamide and hydrazine are now being used instead of water to support regular micelles [10]. Critical fluids such as critical carbon dioxide are... 

Fig. 3.24 Test of the tensile strength hysteresis of hysteresis (Everett and Burgess ). TjT, is plotted against — Tq/Po where is the critical temperature and p.. the critical pressure, of the bulk adsorptive Tq is the tensile strength calculated from the lower closure point of the hysteresis loop. C), benzene O. xenon , 2-2 dimethyl benzene . nitrogen , 2,2,4-trimethylpentane , carbon dioxide 4 n-hexane. The lowest line was calculated from the van der Waals equation, the middle line from the van der Waals equation as modified by Guggenheim, and the upper line from the Berthelot equation. (Courtesy Everett.)...

During the nineteenth century the growth of thermodynamics and the development of the kinetic theory marked the beginning of an era in which the physical sciences were given a quantitative foundation. In the laboratory, extensive researches were carried out to determine the effects of pressure and temperature on the rates of chemical reactions and to measure the physical properties of matter. Work on the critical properties of carbon dioxide and on the continuity of state by van der Waals provided the stimulus for accurate measurements on the compressibiUty of gases and Hquids at what, in 1885, was a surprisingly high pressure of 300 MPa (- 3,000 atmor 43,500 psi). This pressure was not exceeded until about 1912. 

Solvent Strength of Pure Fluids. The density of a pure fluid is extremely sensitive to pressure and temperature near the critical point, where the reduced pressure, P, equals the reduced temperature, =1. This is shown for pure carbon dioxide in Figure 2. Consider the simple case of the solubihty of a soHd in this fluid. At ambient conditions, the density of the fluid is 0.002 g/cm. Thus the solubiUty of a soHd in the gas is low and is given by the vapor pressure over the total pressure. The solubiUties of Hquids are similar. At the critical point, the density of CO2 is 0.47 g/cm. This value is nearly comparable to that of organic Hquids. The solubiHty of a soHd can be 3—10 orders of magnitude higher in this more Hquid-like CO2. 

A unique problem arises when reducing the fissile isotope The amount of that can be reduced is limited by its critical mass. In these cases, where the charge must be kept relatively small, calcium becomes the preferred reductant, and iodine is often used as a reaction booster. This method was introduced by Baker in 1946 (54). Researchers at Los Alamos National Laboratory have recently introduced a laser-initiated modification to this reduction process that offers several advantages (55). A carbon dioxide laser is used to initiate the reaction between UF and calcium metal. This new method does not requite induction heating in a closed bomb, nor does it utilize iodine as a booster. This promising technology has been demonstrated on a 200 g scale. 

Some values of physical properties of CO2 appear in Table 1. An excellent pressure—enthalpy diagram (a large Mohier diagram) over 260 to 773 K and 70—20,000 kPa (10—2,900 psi) is available (1). The thermodynamic properties of saturated carbon dioxide vapor and Hquid from 178 to the critical point,... 

Methods of Liquefaction and Solidification. Carbon dioxide may be Hquefted at any temperature between its triple poiat (216.6 K) and its critical poiat (304 K) by compressing it to the corresponding Hquefaction pressure, and removing the heat of condensation. There are two Hquefaction processes. In the first, the carbon dioxide is Hquefted near the critical temperature water is used for cooling. This process requires compression of the carbon dioxide gas to pressures of about 7600 kPa (75 atm). The gas from the final compression stage is cooled to about 305 K and then filtered to remove water and entrained lubricating oil. The filtered carbon dioxide gas is then Hquefted ia a water-cooled condenser. 

Dimethyl carbonate [616-38-6] and dimethyl oxalate [553-90-2] are both obtained from carbon monoxide, oxygen, and methanol at 363 K and 10 MPa (100 atm) or less. The choice of catalyst is critical cuprous chloride (66) gives the carbonate (eq. 20) a palladium chloride—copper chloride mixture (67,68) gives the oxalate, (eq. 21). Anhydrous conditions should be maintained by removing product water to minimize the formation of by-product carbon dioxide. 

Oxychlorination of Ethylene or Dichloroethane. Ethylene or dichloroethane can be chlorinated to a mixture of tetrachoroethylene and trichloroethylene in the presence of oxygen and catalysts. The reaction is carried out in a fluidized-bed reactor at 425°C and 138—207 kPa (20—30 psi). The most common catalysts ate mixtures of potassium and cupric chlorides. Conversion to chlotocatbons ranges from 85—90%, with 10—15% lost as carbon monoxide and carbon dioxide (24). Temperature control is critical. Below 425°C, tetrachloroethane becomes the dominant product, 57.3 wt % of cmde product at 330°C (30). Above 480°C, excessive burning and decomposition reactions occur. Product ratios can be controlled but less readily than in the chlorination process. Reaction vessels must be constmcted of corrosion-resistant alloys. 

Conventional nitrocellulose lacquer finishing leads to the emission of large quantities of solvents into the atmosphere. An ingeneous approach to reducing VOC emissions is the use of supercritical carbon dioxide as a component of the solvent mixture (172). The critical temperature and pressure of CO2 are 31.3°C and 7.4 MPa (72.9 atm), respectively. Below that temperature and above that pressure, CO2 is a supercritical fluid. It has been found that under these conditions, the solvency properties of CO2 ate similar to aromatic hydrocarbons (see Supercritical fluids). The coating is shipped in a concentrated form, then metered with supercritical CO2 into a proportioning airless spray gun system in such a ratio as to reduce the viscosity to the level needed for proper atomization. VOC emission reductions of 50% or more are projected. 

Catchpole-Kinp examined binaiy diffusion data of near-critical fluids in the reduced density range of 1 to 2.5 and found that their data correlated with average deviations of 10 percent and a maximum deviation of 60 percent. They observed two classes of behavior. For the first, no correction fac tor was required R = 1). That class was comprised of alcohols as solvents with aromatic or ahphatic solutes, or carbon dioxide as a solvent with ahphatics except ketones as solutes, or... 

The two fluids most often studied in supercritical fluid technology, carbon dioxide and water, are the two least expensive of all solvents. Carbon dioxide is nontoxic, nonflammable, and has a near-ambient critical temperature of 31.1°C. CO9 is an environmentally friendly substitute for organic solvents including chlorocarbons and chloroflu-orocarbons. Supercritical water (T = 374°C) is of interest as a substitute for organic solvents to minimize waste in extraction and reaction processes. Additionally, it is used for hydrothermal oxidation of hazardous organic wastes (also called supercritical water oxidation) and hydrothermal synthesis. 

---