Carbon-black, analysis

Table 2.7 lists techniques used to characterise carbon-blacks. Analysis of CB in rubber vulcanisates requires recovery of CB by digestion of the matrix followed by filtration, or by nonoxidative pyrolysis. Dispersion of CB within rubber products is usually assessed by the Cabot dispersion test, or by means of TEM. Kruse [46] has reviewed rubber microscopy, including the determination of the microstructure of CB in rubber compounds and vulcanisates and their qualitative and quantitative determination. Analysis of free CB features measurements of (i) particulate and aggregate size (SEM, TEM, XRD, AFM, STM) (ii) total surface area according to the BET method (ISO 4652), iodine adsorption (ISO 1304) or cetyltrimethylammonium bromide (CTAB) adsorption (ASTM D 3765) and (iii) external surface area, according to the dibutylphthalate (DBP) test (ASTM D 2414). TGA is an excellent technique for the quantification of CB in rubbers. However, it is very limited in being able to distinguish the different types of... 

The analysis is thus relatively exact for heterogeneous surfaces and is especially valuable for analyzing changes in an adsorbent following one or another treatment. An example is shown in Fig. XVII-24 [160]. This type of application has also been made to carbon blacks and silica-alumina catalysts [106a]. House and Jaycock [161] compared the Ross-Olivier [55] and Adamson-Ling... 

Fig. 4. Aggregate size distributions by electron microscope image analysis (D and centrifugal (Z9 sedimentations for N220 and N351 carbon blacks (8).

Shock isolation is also possible usiag the dampiag characteristics of FZ elastomer. Dynamic mechanical analysis iadicates multiple transitions and a broad dampiag peak. This dampiag can be enhanced usiag formulatioas containing both siUca and carbon black fillers. 

Gravimetric analysis, carbon black, quartz, silica... 

In all tests, there was no sign of carbon black formation. Pressure drop over the reactor remained constant during the whole operating period, and there was no accumulation of free carbon on the catalyst. Analysis of the discharged catalyst for free carbon revealed that the carbon content was lower than the amount of carbon added to the catalyst as a pelletizing aid. 

Thermal stability is a crucial factor when polysaccharides are used as reinforcing agents because they suffer from inferior thermal properties compared to inorganic fillers. However, thermogravimetric analysis (TGA) of biocomposites suggested that the degradation temperatures of biocomposites are in close proximity with those of carbon black composites (Table-1). 

Carbon Black Partition Coefficient from the Analysis of C"(t) Signals... 

Although many interface models have been given so far, they are too qualitative and we can hardly connect them to the mechanics and mechanism of carbon black reinforcement of rubbers. On the other hand, many kinds of theories have also been proposed to explain the phenomena, but most of them deal only with a part of the phenomena and they could not totally answer the above four questions. The author has proposed a new interface model and theory to understand the mechanics and mechanism of carbon black reinforcement of rubbers based on the finite element method (FEM) stress analysis of the filled system, in journals and a book. In the new model and theory, the importance of carbon gel (bound rubber) in carbon black reinforcement of rubbers is emphasized repeatedly. Actually, it is not too much to say that the existence of bound rubber and its changeable and deformable characters depending on the magnitude of extension are the essence of carbon black reinforcement of rubbers. 

The new interface model and the concept for the carbon black reinforcement proposed by the author fundamentally combine the structure of the carbon gel (bound mbber) with the mechanical behavior of the filled system, based on the stress analysis (FEM). As shown in Figure 18.6, the new model has a double-layer stmcture of bound rubber, consisting of the inner polymer layer of the glassy state (glassy hard or GH layer) and the outer polymer layer (sticky hard or SH layer). Molecular motion is strictly constrained in the GH layer and considerably constrained in the SH layer compared with unfilled rubber vulcanizate. Figure 18.7 is the more detailed representation to show molecular packing in both layers according to their molecular mobility estimated from the pulsed-NMR measurement. 

Results of a Fingerprint Analysis of a Masterbatch and Remill Mixing Process of a Styrene-Butadiene Rubber-Carbon Black (SBR-CB) Compound on a CK320E Intermeshing Mixer with PES3 Rotors (Harburg Freudenberger)... 

For accurate determination of the particle size, the particle size analyzer was used and particle sizes of carbons sjmthesized are compared with commercial carbon black (N700 and N800, KCB) in Table 2. It was confirmed from particle size analysis that particle size of carbon increased with increase of methane flow rate, as also appeared from SEM analysis. 

N. Moroni, G. Calloni, and A. MarcotulUo. Gas impermeable carbon black cements analysis of field performances. In Proceedings Volume, volume 2, pages 781-792. E P Forum et al Offshore Mediter Conf (OMC 97) (Ravenna, Italy, 3/19-3/21), 1997. 

A cleanup procedure is usually carried out to remove co-extracted matrix components that may interfere in the chromatographic analysis or be detrimental to the analytical instrument. The cleanup procedure is dependent on the nature of the analyte, the type of sample to be analyzed, and the selectivity and sensitivity of the analytical instrument used in the analysis. Preliminary purification of the sample extracts prior to chromatographic separation involves liquid-liquid partitioning and/or solid-phase extraction (SPE) using charcoal/Celite, Elorisil, carbon black, silica, or aminopropyl-silica based adsorbents or gel permeation chromatography (GPC). 

Table 2.4) or proprietary test methods. Forrest [38] has listed 94 international rubber analysis standards (ISO) and 20 ISO standards in preparation referring to latices, carbon-black-filled compositions, raw and compounded rubbers. 

Okumoto [89] has reported an analytical scheme (Scheme 2.8) for automotive rubber products (ENB-EPDM vulcanisates). For high-resolution PyGC analysis, organic additives are first removed from the rubber/(CB, inorganics) formulation. Carbon-black and inorganic material hardly interfere with pyrolysis. For the analysis of the additives the extracted soluble... 

As microwave sample preparation has evolved, standard microwave procedures have been developed and approved by numerous standard methods organisations (ASTM, AOAC International, EPA, etc.), see ref. [64]. Examples are standard test methods for carbon black/ash content (ASTM Method D 1506-97), lead analysis in direct paint samples (ASTM Method E 1645-94), etc. Table 8.15 shows some microwave ashing references (detection weight). A French AFNOR method utilises the atmospheric pressure single-mode microwave method as an alternative sample preparation procedure for Kjeldahl nitrogen determination [84], The performance of a microwave-assisted decomposition for rapid determination of glass fibre content in plastics for QC has been described [85]. 

Rwei, S. P., Manas-Zloczower, I., and Feke, D. L., Analysis of the dispersion of carbon black in polymeric melts and its effect on compound properties. Polym. Eng. ScL 32, 130-135 (1992). 

The sample pretreatment steps for surfactant analysis such as extraction and concentration can be carried out in a variety of ways. Most of the common and well tested procedures have been described by Schmitt [46]. Solid phase extraction (SPE) with C2, Cg or Cis and divinyl benzene resins as well as special phases, e.g. graphitised carbon black (GCB), can be adequate methods, especially for SPE of metabolites from... 

---