Butyl rubber adhesives

Butyl rubber is an elastomeric polymer used widely in adhesives and sealants, both as primary binders and as tackifiers and modifiers. Butyl rubber is a copolymer of isobutylene with a small amount of 

---

Prime with butyl rubber adhesive in an aliphatic solvent. 

The wide variety of grades available provides for an extremely diverse array of properties that can be developed for butyl rubber adhesives and sealants. However, the following general properties apply to varying degrees. 

Uses Emollient, skin conditioner in cosmetics lubricant, processing aid for butyl rubber, adhesives, inks, cosmetics, greases, paints opacifier, pearlescent, emulsifier, vise, builder for surfactant systems defoamer in food-contact paper/paperboard Reguiatory FDA 21CFR 176.210... 

Butyl rubber is an elastomeric polymer used widely in adhesives and sealants, both as primary binders and as tackifiers and modifiers. Butyl rubber is a copolymer of isobutylene with a small amount of isoprene. These materials have relatively low strength and tend to exhibit creep under load. They are useful in packaging apphcations where their low permeability to gases, vapors, and moisture can be exploited. Butyl rubber is also used as an adhesive sealant. It is generally applied from a solvent-based solution. Table 5.1 summarizes some of the important properties of butyl rubber adhesives. 

Butyl Toluene 1. Solvent wipe 2. Prime with butyl-rubber adhesive in an aliphatic solvent For genoral-purpose bonding For maximum strength... 

Surface Primers (Dick, 1987) - A surface primer is a coating applied to an adherend to improve an adhesive bond or subsequent coating. It is typically used where die adhesive and adherend have widely differing polarities, a butyl rubber adhesive on a steel surface for example. Primers are of two general types ... 

Butyl mbber, a copolymer of isobutjiene with 0.5—2.5% isoprene to make vulcanization possible, is the most important commercial polymer made by cationic polymerization (see Elastomers, synthetic-butyl rubber). The polymerization is initiated by water in conjunction with AlCl and carried out at low temperature (—90 to —100° C) to prevent chain transfer that limits the molecular weight (1). Another important commercial appHcation of cationic polymerization is the manufacture of polybutenes, low molecular weight copolymers of isobutylene and a smaller amount of other butenes (1) used in adhesives, sealants, lubricants, viscosity improvers, etc. 

Chlorobutyl rubber is prepared by chlorination of butyl rubber (chlorine content is about 1 wt%). This is a substitution reaction produced at the allylic position, so little carbon-carbon double unsaturation is lost. Therefore, chlorobutyl rubber has enhanced reactivity of the carbon-carbon double bonds and supplies additional reactive sites for cross-linking. Furthermore, enhanced adhesion is obtained to polar substrates and it can be blended with other, more unsaturated elastomers. 

Butyl phenolic resin is a typical tackifier for solvent-borne polychloroprene adhesives. For these adhesives, rosin esters and coumarone-indene resins can also be used. For nitrile rubber adhesives, hydrogenated rosins and coumarone-indene resins can be used. For particular applications of both polychloroprene and nitrile rubber adhesives, chlorinated rubber can be added. Styrene-butadiene rubber adhesives use rosins, coumarone-indene, pinene-based resins and other aromatic resins. 

Plasticizers can be classified according to their chemical nature. The most important classes of plasticizers used in rubber adhesives are phthalates, polymeric plasticizers, and esters. The group phthalate plasticizers constitutes the biggest and most widely used plasticizers. The linear alkyl phthalates impart improved low-temperature performance and have reduced volatility. Most of the polymeric plasticizers are saturated polyesters obtained by reaction of a diol with a dicarboxylic acid. The most common diols are propanediol, 1,3- and 1,4-butanediol, and 1,6-hexanediol. Adipic, phthalic and sebacic acids are common carboxylic acids used in the manufacture of polymeric plasticizers. Some poly-hydroxybutyrates are used in rubber adhesive formulations. Both the molecular weight and the chemical nature determine the performance of the polymeric plasticizers. Increasing the molecular weight reduces the volatility of the plasticizer but reduces the plasticizing efficiency and low-temperature properties. Typical esters used as plasticizers are n-butyl acetate and cellulose acetobutyrate. 

Most rubbers used in adhesives are not resistant to oxidation. Because the degree of unsaturation present in the polymer backbone of natural rubber, styrene-butadiene rubber, nitrile rubber and polychloroprene rubber, they can easily react with oxygen. Butyl rubber, however, possesses small degree of unsaturation and is quite resistant to oxidation. The effects of oxidation in rubber base adhesives after some years of service life can be assessed using FTIR spectroscopy. The ratio of the intensities of the absorption bands at 1740 cm" (carbonyl group) and at 2900 cm" (carbon-hydrogen bonds) significantly increases when the elastomer has been oxidized [50]. 

All grades of regular butyl rubber are tacky, rubbery and contain less unsaturation than natural rubber or styrene-butadiene rubber. On the other hand, low molecular weight grades of polyisobutylene are permanently tacky and are clear white semi-liquids, so they can be used as permanent tackifiers for cements, PSAs, hot-melt adhesives and sealants. Low molecular weight polyisobutylenes also provide softness and flexibility, and act as an adhesion promoter for difficult to adhere surfaces (e.g. polyolefins). 

Cohesive strength of these adhesives can be modified by blending butyl rubber and polyisobutylene. Higher strength is obtained by using high molecular weight PIB or butyl rubber. On the other hand, blends of butyl rubber or PIB with chlorinated butyl rubber show improved cure properties. 

Butyl ruhher vulcanizates have tensile strengths up to 2,000 psi, and are characterized hy low permeahility to air and a high resistance to many chemicals and to oxidation. These properties make it a suitable rubber for the production of tire inner tubes and inner liners of tubeless tires. The major use of butyl rubber is for inner tubes. Other uses include wire and cable insulation, steam hoses, mechanical goods, and adhesives. Chlorinated butyl is a low molecular weight polymer used as an adhesive and a sealant. 

Laminated tapes In more general use now than pressure sensitive tapes are tapes consisting of polyvinyl chloride or polyethylene films in conjunction with butyl rubber. These tapes are applied with an adhesive butyl rubber primer. Thicknesses of up to 0-75 mm are in use and loose protective outer wraps of p.v.c. or polyethylene sheet are commonly applied. Tape quality control is exercised with reference to ASTM standard test methods and may include water vapour transmission rate and elongation. 

Generally, systems developed in the USA favour a combination of polyethylene with either butyl-rubber or hot-applied mastic adhesives, the latter consisting of a blend of rubber, asphalt and high molecular weight resins. In European and Far East coating plants, epoxy type primers and hard ethylene copolymer adhesives have been successfully employed. 

Methylpropene can be made to continue the process to yield high polymers—cationic polymerisation—but most simple alkenes will go no further than di- or tri-meric structures. The main alkene monomers used on the large scale are 2-methyIpropene (— butyl rubber ), and vinyl ethers, ROCH=CH2 (— adhesives). Cationic polymerisation is often initiated by Lewis acid catalysts, e.g. BF3, plus a source of initial protons, the co-catalyst, e.g. traces of HzO etc. polymerisation occurs readily at low temperatures and is usually very rapid. Many more alkenes are polymerised by a radical induced pathway, however (p. 320). 

The advanced applications for nitrocellulose plastisol propellants require that they be integrally bonded to the motor case. Successful case bonding for the multiyear storage life of a rocket calls for special adhesives and liners which are completely compatible with these highly plasticized propellants. Best results have been obtained with a combination of an impervious rubber liner and a crosslinked adhesive system with a limited affinity for the plasticizers used in the propellants. Examples of effective liners are silica-filled butyl rubber and chlorinated synthetic rubber. Epoxy polyamides, isocyanate-crosslinked cellulose esters, and combinations of crosslinked phenol-formaldehyde and polyvinyl formal varnishes have proved to be effective adhesives between propellant and impervious liners. Pressure curing of the propellants helps... 

Isobutylene is more reactive than n-butene and has several industrial uses. It undergoes dimerization and trimerization reactions when heated in the presence of sulfuric acid. Isobutylene dimer and trimers are use for alkylation. Polymerization of isobutene produces polyisobutenes. Polyisobutenes tend to be soft and tacky, and do not set completely when used. This makes polyisobutenes ideal for caulking, sealing, adhesive, and lubricant applications. Butyl rubber is a co-polymer of isobutylene and isoprene containing 98% isobutene and 2% isoprene. 

---