Barium powders

Finely divided barium is susceptible to rapid, violent combination with atmospheric oxygen. Therefore, in powdered form it must be considered pyrophoric and very dangerous to handle in the presence of air or other oxidising gases. Barium powder must be stored under dry argon or helium to avoid the possibihty of violent explosions. Massive pieces of barium, however, oxidize relatively slowly and present no explosion hazard if kept dry. 

Alkali metal dispersions, 4.3 Alkaline earth metal dispersion, 4.3 Aluminium, powder Aluminium powder, coated, 4.1 Aluminium powder, pyrophoric Aluminium powder, uncoated, 4.3 Aluminium powder, uncoated, non-pyrophoric, 4.3 Antimony powder, 6.1 Barium dispersions Barium, powder Barium powder, pyrophoric, 4.2... 

The degree of subdivision of metal has been found to be of importance in the case of barium. With a-methyl styrene, barium powder gave mostly the dicarbanionic dimer but with a dispersion of metal the principal product was the monocarbanionic oligomer. Dicarbanionic oligostyryl barium forms a cyclic associate in THF and in tetrahydropyran. The adsorption maximum is sensitive to the ring size, ranging from 368 nm for the dimer to 359 nm when the... 

McCormick MJ, Moon KB, Jones SR, Hanusa TP (1990) Preparation of activated calcium, strontium, and barium powders by reduction of alkaline earth di-iodides. J Chem Soc, Chem Commun 778-779... 

Mix 200 g. of adipic acid intimately with 10 g. of finely-powdered, crystallised barium hydroxide. Place the mixture in a 1-litre distilling flask, fitted with a thermometer reaching to within 5 mm. of the bottom connect the flask with a condenser and receiver. Heat the mixture gradually in an air bath (1) to 285-295° during about 90 minutes and maintain it at this temperature mitil only a small amount of dry residue remains in the flask this requires a further 2 hours. The temperature must not be allowed to rise above 300°, since at this temperature the adipic acid distils quite rapidly the best working temperature is 290°. The cycZopentanone distils slowly accompanied by a little adipic acid. Separate the ketone from the water in the distillate, and dry it with anhydrous potassium carbonate this treatment simultaneously removes the traces of adipic acid present. Finally distil from a flask of suitable size and collect the cycZopentanone at 128-131°. The yield is 92 g. 

Dissolve 15-0 g. of A.R. barium nitrate and 130 g. of A.R. cupric nitrate trihydrate in 450 ml. of water at 80°. Prepare a solution of sodium chromate by dissolving 89 g. of recrystallised sodium dichromate dihydrate in 200 ml. of water and adding 112 5 ml. of cone, ammonia solution (sp. gr. 0-90). Add the warm solution (80°) of nitrates in a thin stream, with stirring, to the sodium chromate solution (at 25°). Collect the orange precipitate by suction Bltration, wash it with two 50 ml. portions of 5fiter, drain well, and dry at 75-80° for 12 hours powder finely. 

Prepare a solution of 41 g. of anhydrous palladium chloride (1) in 10 ml. of concentrated hydrochloric acid and 25 ml. of water (as in A). Add all at once 60 ml. of 6iV-sulphuric acid to a rapidly stirred, hot (80°) solution of 63 1 g. of A.R. crystallised barium hydroxide in 600 ml. of water contained in a 2-htre beaker. Add more 6iV-sulphuric acid to render the suspension just acid to htmus (5). Introduce the palladium chloride solution and 4 ml. of 37 per cent, formaldehyde solution into the hot mechanically stirred suspension of barium sulphate. Render the suspension slightly alkaline with 30 per cent, sodium hydroxide solution, continue the stirring for 5 minutes longer, and allow the catalyst to settle. Decant the clear supernatant hquid, replace it by water and resuspend the catalyst. Wash the catalyst by decantation 8-10 times and then collect it on a medium - porosity sintered glass funnel, wash it with five 25 ml. portions of water and suck as dry as possible. Dry the funnel and contents at 80°, powder the catalyst (48 g.), and store it in a tightly stoppered bottle. 

K. Osseo-Asare, F. J. Arriagada, and J. H. Adair, "Solubility Relationships in the Coprecipitation Synthesis of Barium Titanate Heterogeneous Equihbria in the Ba—Ti—C2O4—H2O System," in G. L. Messing, E. R. Fuller, Jr., and Hans Hausin, eds.. Ceramic Powder Science Vol. 2,1987, pp. 47-53. 

Barium fluoride [7782-32-8] Bap2, is a white crystal or powder. Under the microscope crystals may be clear and colorless. Reported melting points vary from 1290 (1) to 1355°C (2), including values of 1301 (3) and 1353°C (4). Differences may result from impurities, reaction with containers, or inaccurate temperature measurements. The heat of fusion is 28 kj/mol (6.8 kcal/mol) (5), the boiling point 2260°C (6), and the density 4.9 g/cm. The solubiUty in water is about 1.6 g/L at 25°C and 5.6 g/100 g (7) in anhydrous hydrogen fluoride. Several preparations for barium fluoride have been reported (8—10). 

The most significant commercial product is barium titanate, BaTiO, used to produce the ceramic capacitors found in almost all electronic products. As electronic circuitry has been rniniaturized, demand has increased for capacitors that can store a high amount of charge in a relatively small volume. This demand led to the development of highly efficient multilayer ceramic capacitors. In these devices, several layers of ceramic, from 25—50 ]lni in thickness, are separated by even thinner layers of electrode metal. Each layer must be dense, free of pin-holes and flaws, and ideally consist of several uniform grains of fired ceramic. Manufacturers are trying to reduce the layer thickness to 10—12 ]lni. Conventionally prepared ceramic powders cannot meet the rigorous demands of these appHcations, therefore an emphasis has been placed on production of advanced powders by hydrothermal synthesis and other methods. 

Table 2. Commercial Hydrothermal Barium Titanate Powders ...

The commercial product is a dull yeUow powder containing about 90% Ba02 and about 8.5% active oxygen the remainder is mainly barium carbonate and barium hydroxide. The principal use is in pyrotechnics, but there are also small uses in the curing of polysulftde mbbers and in the production of certain titanium—aluminum alloys. 

Available Forms. Phthalocyanines are available as powders, in paste, or Hquid forms. They can be dispersed in various media suitable for aqueous, nonaqueous, or multipurpose systems, eg, polyethylene, polyamide, or nitrocellulose. Inert materials like clay, barium sulfate, calcium carbonates, or aluminum hydrate are the most common soHd extenders. Predispersed concentrates of the pigments, like flushes, are interesting for manufacturers of paints and inks (156), who do not own grinding or dispersing equipment. Pigment—water pastes, ie, presscakes, containing 50—75% weight of water, are also available. 

Because the regions of the alimentary tract vary widely ia pH and chemical composition, many different commercial formulations of barium sulfate are available. The final preparations of varyiag viscosity, density, and formulation stabiUty levels are controlled by the different size, shape, uniformity and concentration of barium sulfate particles and the presence of additives. The most important additives are suspending and dispersiag agents used to maintain the suspension stabiUty. Commercial preparations of barium sulfate iaclude bulk and unit-dose powders and suspensions and principal manufacturers are E-Z-EM (Westbury, New York), Lafayette-Pharmacol, Inc. (Lafayette, Indiana), and Picker International, Inc. (Cleveland, Ohio). 

Barium titanate thin films can be deposited on various substances by treating with an aqueous solution containing barium salts and an alkanolamine-modifted titanate such as TYZOR TE (151). In a similar fashion, reaction of a tetraalkyl titanate with an alkah metal hydroxide, such as potassium hydroxide, gives oxyalkoxide derivatives (KTi O(OR) ), which can be further processed to give alkali metal titanate powders, films, and fibers (152—155). The fibers can be used as adsorbents for radioactive metals such as cesium, strontium, and uranium (156). 

The largest use for barium is as a getter to remove the last traces of gases from vacuum and television picture tubes. It is ideal for this use because of its combination of high chemical reactivity and low vapor pressure (28—32). In some cases it is used as powder obtained by vaporization ia an electric arc (33). It can also be used as an aluminum ahoy (see Vacuum technology). 

Barium carbonate prevents formation of scum and efflorescence in brick, tile, masonry cement, terra cotta, and sewer pipe by insolubilizing the soluble sulfates contained in many of the otherwise unsuitable clays. At the same time, it aids other deflocculants by precipitating calcium and magnesium as the carbonates. This reaction is relatively slow and normally requites several days to mature even when very fine powder is used. Consequentiy, often a barium carbonate emulsion in water is prepared with carbonic acid to further increase the solubiUty and speed the reaction. 

Barium carbonate of finely controlled particle size reacts in the soHd state when heated with iron oxide to form barium ferrites. Magnetically aligned barium ferrite [11138-11-7] powder can be pressed and sintered into a hard-core permanent magnet which is used in many types of small motors. Alternatively, ground up magnetic powder can be compounded into plastic strips which are used in a variety of appHances as part of the closure mechanism. 

Barium carbonate also reacts with titania to form barium titanate [12047-27-7] BaTiO, a ferroelectric material with a very high dielectric constant (see Ferroelectrics). Barium titanate is best manufactured as a single-phase composition by a soHd-state sintering technique. The asymmetrical perovskite stmcture of the titanate develops a potential difference when compressed in specific crystallographic directions, and vice versa. This material is most widely used for its strong piezoelectric characteristics in transducers for ultrasonic technical appHcations such as the emulsification of Hquids, mixing of powders and paints, and homogenization of milk, or in sonar devices (see Piezoelectrics Ultrasonics). 

Yttrium—barium—copper oxide, YBa2Cu202 is a newly developed high T material which has been found to be fully superconductive at temperatures above 90 K, a temperature that can be maintained during practical operation. The foremost challenge is to be able to fabricate these materials into a flexible form to prepare wines, fibers, and bulk shapes. Ultrapure powders of yttrium—barium—copper oxide that are sinterable into single-phase superconducting... 

---